> All this talk about Wandboard Quad D1 is because I'm trying to upgrade an > existing device currently running on a Wandboard Dual C1. It's a system > that started as Fedora 25 and was upgraded to Fedora 31 (via dnf > system-upgrade). It's been running fine on the Dual. I upgraded the > U-boot and it still runs fine on the C1, however if I try to use this SD > card in the Quad-D1 I get this during boot: > > [ 6.841555] Freeing unused kernel memory: 2048K > [ 6.848283] ------------[ cut here ]------------ > [ 6.852985] WARNING: CPU: 2 PID: 1 at arch/arm/mm/dump.c:248 > note_page+0x1604 > [ 6.860609] arm/mm: Found insecure W+X mapping at address 0xf0879000 > [ 6.866994] Modules linked in: > [ 6.870093] CPU: 2 PID: 1 Comm: swapper/0 Not tainted > 5.4.17-200.fc31.armv7h1 > [ 6.877494] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) > [ 6.884062] [<c0311264>] (unwind_backtrace) from [<c030b744>] > (show_stack+0x) > [ 6.891825] [<c030b744>] (show_stack) from [<c0b2d580>] > (dump_stack+0xb4/0xd) > [ 6.899068] [<c0b2d580>] (dump_stack) from [<c034d5bc>] (__warn+0xdc/0xf8) > [ 6.905958] [<c034d5bc>] (__warn) from [<c034d96c>] > (warn_slowpath_fmt+0x70/) > [ 6.913455] [<c034d96c>] (warn_slowpath_fmt) from [<c03197a8>] > (note_page+0x) > [ 6.921383] [<c03197a8>] (note_page) from [<c0319a34>] > (walk_pgd+0xc8/0xe0) > [ 6.928357] [<c0319a34>] (walk_pgd) from [<c0319b10>] > (ptdump_check_wx+0x58/) > [ 6.935858] [<c0319b10>] (ptdump_check_wx) from [<c0b4182c>] > (kernel_init+0x) > [ 6.943706] [<c0b4182c>] (kernel_init) from [<c03010e8>] > (ret_from_fork+0x14) > [ 6.951281] Exception stack(0xee943fb0 to 0xee943ff8) > [ 6.956339] 3fa0: 00000000 00000000 > 00000 > [ 6.964524] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 > 00000 > [ 6.972708] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 > [ 6.979365] ---[ end trace eb98c3200f90d0b6 ]--- > [ 6.984352] Checked W+X mappings: FAILED, 1 W+X pages found > [ 6.989965] rodata_test: test data was not read only > > and the system doesn't come up completely. > > If I used a fresh Fedora-Minimal-31 on the Quad-D1 (or the Dual-C1) it > works fine. Currently the main difference, as far as I can see, is that > there is a different kernel. The working system is running > 5.3.7-301.fc31.armv7hl whereas the non-working is running > 5.4.17-200.fc31.armv7hl. > > I am currently working on upgrading the Fedora-Minimal to a more recent > kernel to try to reproduce the problem; if it doesn't reproduce I will > also try to upgrade the existing system. If it DOES reproduce then > clearly there's something with the F25->F31 filesystem, and I will have to > migrate everything to a fresh install :( > > I'll let you know in a couple hours how the testing goes -- unless you've > seen this before and have an easy fix? I've not seen it before but what I recommend is to go to a generic initrd so it pulls in all the drivers, move over to the new device and then allow it to go back to a host specific initrd. I suspect there's slightly different HW requirements. To do this install the dracut-config-generic package and reinstall or upgrade the kernel, it'll be slower to boot, make sure it boots on the current device, move to the new one. Once it's running on the new one remove the package and the next kernel will go back to a host specific initrd with the specific initrd for the new HW. Peter _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
