On Tue, May 15, 2018 at 4:42 AM, RENARD Pierre-Francois <pfrenard@xxxxxxxxx> wrote: > Hey, > > I experienced not booting SD card when I forgot to unmount the SD before > doing the dd command. > (especially when another OS was on it) > check mounts into /run/media/<username> > Thanks for the suggestion. However this is not my case. I don't have any auto mount settings and I did not mount it before dd. I've tried to dd again several times now but still no lucky. > Fox > > > On 05/14/2018 05:26 PM, Zamir SUN wrote: >> >> Hi, >> >> Today I am trying my HikeyBoard (620) with >> Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot. >> >> I confirmed the xz image has the same hash as is shown on the mirror. I >> used the following command to write to my TF card. >> xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress >> bs=4M of=/dev/mmcblk0 >> >> The system failed in dracut init queue timeout, with a warning "Warning: >> /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist " >> >> However I confirmed the uuid is right for my partition. >> >> Besides, I cannot type anything via minicon to it so I cannot really >> debug more right now. I am posting the last block of message via UART. >> >> So anyone have some hints for this? Thanks in advance! >> >> (P.S. Fedora 27 works fine on my hikey board). >> >> >> [ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout >> - starts >> [ 222.639909] dracut-initqueue[468]: Warning: Could not boot. >> >> Starting Setup Virtual Console... >> >> [ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1 >> uid=0 au' >> ] Started Setup [ 222.738436] audit: type=1131 >> audit(1520288415.819:15): pid=1' >> Virtual Console. >> >> Starting Dracut Emergency Shell... >> >> [ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0 >> auid=4294' >> Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not >> exist >> >> >> Generating "/run/initramfs/rdsosreport.txt" >> >> [ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 222.967237] print_req_error: 6 callbacks suppressed >> >> [ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1 >> >> [ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0 >> >> [ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1 >> >> [ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async >> page read >> [ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1 >> >> [ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0 >> >> [ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1 >> >> [ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async >> page read >> [ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0 >> >> [ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1 >> >> [ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1 >> >> [ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2 >> >> [ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> [ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req >> 400000H) >> [ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req >> 1000000) >> > _______________________________________________ > arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx -- Ziqian SUN (Zamir) zsun@xxxxxxxxxxxxxxxxx GPG : 1D86 6D4A 49CE 4BBD 72CF FCF5 D856 6E11 F2A0 525E Want to know more about Fedora? Visit https://fedoraproject.org/wiki/ _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
