Hey,
I experienced not booting SD card when I forgot to unmount the SD before
doing the dd command.
(especially when another OS was on it)
check mounts into /run/media/<username>
Fox
On 05/14/2018 05:26 PM, Zamir SUN wrote:
Hi,
Today I am trying my HikeyBoard (620) with
Fedora-Minimal-28-1.1.aarch64.raw.xz. It simply cannot boot.
I confirmed the xz image has the same hash as is shown on the mirror. I
used the following command to write to my TF card.
xzcat Fedora-Minimal-28-1.1.aarch64.raw.xz | sudo dd status=progress
bs=4M of=/dev/mmcblk0
The system failed in dracut init queue timeout, with a warning "Warning:
/dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not exist "
However I confirmed the uuid is right for my partition.
Besides, I cannot type anything via minicon to it so I cannot really
debug more right now. I am posting the last block of message via UART.
So anyone have some hints for this? Thanks in advance!
(P.S. Fedora 27 works fine on my hikey board).
[ 222.639468] dracut-initqueue[468]: Warning: dracut-initqueue timeout
- starts
[ 222.639909] dracut-initqueue[468]: Warning: Could not boot.
Starting Setup Virtual Console...
[ OK [ 222.716760] audit: type=1130 audit(1520288415.819:14): pid=1
uid=0 au'
] Started Setup [ 222.738436] audit: type=1131
audit(1520288415.819:15): pid=1'
Virtual Console.
Starting Dracut Emergency Shell...
[ 222.825449] audit: type=1131 audit(1520288415.929:16): pid=1 uid=0
auid=4294'
Warning: /dev/disk/by-uuid/9a926ac9-5938-4539-bb79-72f87b36095f does not
exist
Generating "/run/initramfs/rdsosreport.txt"
[ 222.897318] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 222.956555] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 222.967237] print_req_error: 6 callbacks suppressed
[ 222.967243] print_req_error: I/O error, dev mmcblk0, sector 1
[ 222.985808] print_req_error: I/O error, dev mmcblk0, sector 0
[ 222.991640] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.001405] Buffer I/O error on dev mmcblk0, logical block 0, async
page read
[ 223.032457] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.089436] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 223.100132] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.114267] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.120128] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.129994] Buffer I/O error on dev mmcblk0, logical block 0, async
page read
[ 223.176307] print_req_error: I/O error, dev mmcblk0, sector 0
[ 223.182146] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.211348] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.268935] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 223.279748] print_req_error: I/O error, dev mmcblk0, sector 1
[ 223.285597] print_req_error: I/O error, dev mmcblk0, sector 2
[ 223.313471] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.373025] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 223.442453] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.499139] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 223.533285] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.592543] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 223.663611] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.723301] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
[ 223.757851] mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req
400000H)
[ 223.817927] mmc_host mmc0: Bus speed (slot 0) = 99200000Hz (slot req
1000000)
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
