On Wed, Feb 1, 2017 at 3:58 PM, Rafael Leiva-Ochoa <spawn@xxxxxxxxxxx> wrote: > The AMP rating is 2.0 amps for mine. Its been working fine since the first > release of Fedora 25. I have been noticing that the Pi does go a little hot > compared to my other Pi's that don't run Fedora. I don't know if that is > related. As outlined in the Fedora perquisites [1] as documented by the RPi Foundation [2] you need a 2.5 Amp PSU for the Pi3. There was quite a bit of change between the 4.8 and 4.9 kernel series so it might be we've enabled extra functionality that's drawing a little extra power when you do something (eg I add patches that use higher speed SD card support) and that might have been enough to trip us over the "it works" on a 2 AMP PSU. [1] https://fedoraproject.org/wiki/Raspberry_Pi#Prerequisites [2] https://www.raspberrypi.org/help/faqs/#power > Thanks, > > Rafael > > On Wed, Feb 1, 2017 at 4:58 AM, Winfried de Heiden <wdh@xxxxxx> wrote: >> >> Hi all, >> >> I don't know by head but it should be enough; it worked for weeks and it >> is sold as "the official PI power supply". >> >> I'll check tonight to be shure. >> >> Winfried >> >> -----Oorspronkelijke bericht----- >> >> Datum: Wed, 1 Feb 2017 11:27:45 +0000 >> Onderwerp: [fedora-arm] Re: Raspberry PI 3 locking up >> Cc: arm@xxxxxxxxxxxxxxxxxxxxxxx, Rafael Leiva-Ochoa <spawn@xxxxxxxxxxx> >> Aan: Winfried de Heiden <wdh@xxxxxx> >> Van: Peter Robinson <pbrobinson@xxxxxxxxx> >> >> On Wed, Feb 1, 2017 at 7:52 AM, Winfried de Heiden <wdh@xxxxxx> wrote: >> >> Hi all, >> >> Same for me, since a couple of days the Rapsbery Pi 3 suddenly stops. One >> or >> two time I was quick enough to catch a kernel panic on the screen. >> >> Looks like a kernel thing to me. I moved the SD-card to my " old" >> Raspberry >> Pi 2 (two), the same installation is running fine for a couple of days. >> >> >> What is the AMP rating of your power supplies? >> >> >> Screen shot of the kernel panic attached. I think I' ll create a bugzilla >> on >> this. >> >> Winfried >> >> >> >> Op wo, 1 feb 2017 om 1:26 , schreef Rafael Leiva-Ochoa >> <spawn@xxxxxxxxxxx>: >> >> Hi Everyone, >> >> I've been running a raspberry pi 3 with Fedora release 25 (Twenty >> Five) >> using kernal 4.9.6-200.fc25.armv7hl, and I have been noticing for the last >> 2 >> weeks that my Pi locks up. I tried hooking it up to an HDMI monitor, and >> USB >> keyboard to see if the system generates any message, but I only get a >> blank >> screen and no reaction from the keyboard. I have looked at the >> /var/log/message, and dmesg, and I don't see anything that could be >> causing >> the problem. I was thinking it could be overheating, but Fedara 25 does >> not >> support any of the rasbian commands to run heat sensor checks. >> >> Any ideas? >> >> Thanks, >> >> Rafael >> >> >> _______________________________________________ >> arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx >> To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx >> >> >> _______________________________________________ >> arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx >> To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > > _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
