Re: Cubietruck failure with Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)

[Robert Moskowitz <rgm@xxxxxxxxxxxxxxx>]

On 10/24/2015 03:31 AM, Zamir SUN wrote:
> I hit similar bugs when using a wrong uboot on BBB. So maybe you 
> should also check if your uboot is up to date.

Paul's script puts the uboot from the image onto the card as its last 
step.  So in theory...

> Zamir
>
> On 10/24/2015 06:38 AM, Paul Whalen wrote:
> > ----- Original Message -----
> > > Sunday/monday I will try another card. I have used this card many times
> > > in the past, using your script to lay down the image on the card.
> >
> > I hit it as well, with a card that been used in the past.. tried another
> > and it worked fine..
> >
> > Pasted below:
> >
> >
> > U-Boot SPL 2015.07 (Sep 12 2015 - 10:46:32)
> > DRAM: 2048 MiB
> > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> >
> >
> > U-Boot 2015.07 (Sep 12 2015 - 10:46:32 +0000) Allwinner Technology
> >
> > CPU:   Allwinner A20 (SUN7I)
> > I2C:   ready
> > DRAM:  2 GiB
> > MMC:   SUNXI SD/MMC: 0
> > *** Warning - bad CRC, using default environment
> >
> > HDMI connected: Setting up a 1920x1080 hdmi console
> > In:    serial
> > Out:   vga
> > Err:   vga
> > SCSI:  SUNXI SCSI INIT
> > SATA link 0 timeout.
> > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> > flags: ncq stag pm led clo only pmp pio slum part ccc apst
> > Net:   eth0: ethernet@01c50000
> > starting USB...
> > USB0:   USB EHCI 1.00
> > USB1:   USB OHCI 1.0
> > USB2:   USB EHCI 1.00
> > USB3:   USB OHCI 1.0
> > scanning bus 0 for devices... 1 USB Device(s) found
> > scanning bus 2 for devices... 1 USB Device(s) found
> > scanning bus 1 for devices... unable to get device descriptor (error=-1)
> > 1 USB Device(s) found
> > scanning bus 3 for devices... 1 USB Device(s) found
> > Hit any key to stop autoboot:  0
> > switch to partitions #0, OK
> > mmc0 is current device
> > Scanning mmc 0:1...
> > Found /extlinux/extlinux.conf
> > Retrieving file: /extlinux/extlinux.conf
> > 515 bytes read in 111 ms (3.9 KiB/s)
> > Ignoring unknown command: ui
> > Ignoring malformed menu command:  autoboot
> > Ignoring malformed menu command:  hidden
> > Ignoring unknown command: totaltimeout
> > Fedora-Xfce-armhfp-23-3 Boot Options.
> > 1:      Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
> > Enter choice: 1:        Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
> > Retrieving file: /initramfs-4.2.3-300.fc23.armv7hl.img
> > 43337044 bytes read in 2308 ms (17.9 MiB/s)
> > Retrieving file: /vmlinuz-4.2.3-300.fc23.armv7hl
> > 5811776 bytes read in 391 ms (14.2 MiB/s)
> > append: console=ttyS0,115200 ro 
> > root=UUID=29ec3011-cc4c-4c7b-9ab8-2697716fd3c7
> > Retrieving file: /dtb-4.2.3-300.fc23.armv7hl/sun7i-a20-cubietruck.dtb
> > 28110 bytes read in 2643 ms (9.8 KiB/s)
> > Kernel image @ 0x42000000 [ 0x000000 - 0x58ae40 ]
> > ## Flattened Device Tree blob at 43000000
> >     Booting using the fdt blob at 0x43000000
> >     Loading Ramdisk to 4c6ab000, end 4efff554 ... OK
> >     Loading Device Tree to 4c6a1000, end 4c6aadcd ... OK
> >
> > Starting kernel ...
> >
> > [    0.000000] Booting Linux on physical CPU 0x0
> > [    0.000000] Initializing cgroup subsys cpuset
> > [    0.000000] Initializing cgroup subsys cpu
> > [    0.000000] Initializing cgroup subsys cpuacct
> > [    0.000000] Linux version 4.2.3-300.fc23.armv7hl 
> > (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 5.1.1 
> > 20150618 (Red Hat 5.1.1-4) (GCC) ) #1 SMP Mon Oct 5 16:45:59 UTC 2015
> > [    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), 
> > cr=10c5387d
> > [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing 
> > instruction cache
> > [    0.000000] Machine model: Cubietech Cubietruck
> > [    0.000000] cma: Reserved 16 MiB at 0xbe800000
> > [    0.000000] Memory policy: Data cache writealloc
> > [    0.000000] psci: probing for conduit method from DT.
> > [    0.000000] psci: Using PSCI v0.1 Function IDs from DT
> > [    0.000000] PERCPU: Embedded 12 pages/cpu @ee5c0000 s19840 r8192 
> > d21120 u49152
> > [    0.000000] Built 1 zonelists in Zone order, mobility grouping 
> > on.  Total pages: 520553
> > [    0.000000] Kernel command line: console=ttyS0,115200 ro 
> > root=UUID=29ec3011-cc4c-4c7b-9ab8-2697716fd3c7
> > [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
> > [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 
> > 524288 bytes)
> > [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 
> > 262144 bytes)
> > [    0.000000] Memory: 1997348K/2089052K available (7232K kernel 
> > code, 1075K rwdata, 3288K rodata, 1036K init, 843K bss, 75320K 
> > reserved, 16384K cma-reserved, 1294428K highmem)
> > [    0.000000] Virtual kernel memory layout:
> > [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
> > [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
> > ..
> >
> >
> > > On 10/23/2015 01:54 PM, Paul Whalen wrote:
> > > > ----- Original Message -----
> > > > > It has been a while since I tried any Fedora-23 builds what with a
> > > > > number of things going on.  So seeing the go/nogo, I figured I better
> > > > > run a test and as you can see it failed (and I tried booting twice 
> > > > > with
> > > > > this image and got the same results):
> > > > The image is working Ok here(tested on the Banana Pi Pro), I've 
> > > > found the
> > > > Cubietruck to be a little picky with mSD's and Ive seen the same error
> > > > when using anything but Silicon Power branded cards. YMMV..
> > > >
> > > > Thanks for testing Robert!
> > > >
> > > > Paul
> > > >
> > > >
> > > > > U-Boot SPL 2015.07 (Sep 12 2015 - 10:46:32)
> > > > > DRAM: 2048 MiB
> > > > > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> > > > >
> > > > >
> > > > > U-Boot 2015.07 (Sep 12 2015 - 10:46:32 +0000) Allwinner Technology
> > > > >
> > > > > CPU:   Allwinner A20 (SUN7I)
> > > > > I2C:   ready
> > > > > DRAM:  2 GiB
> > > > > MMC:   SUNXI SD/MMC: 0
> > > > > *** Warning - bad CRC, using default environment
> > > > >
> > > > > Setting up a 1024x768 vga console
> > > > > In:    serial
> > > > > Out:   vga
> > > > > Err:   vga
> > > > > SCSI:  SUNXI SCSI INIT
> > > > > SATA link 0 timeout.
> > > > > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> > > > > flags: ncq stag pm led clo only pmp pio slum part ccc apst
> > > > > Net:   eth0: ethernet@01c50000
> > > > > starting USB...
> > > > > USB0:   USB EHCI 1.00
> > > > > USB1:   USB OHCI 1.0
> > > > > USB2:   USB EHCI 1.00
> > > > > USB3:   USB OHCI 1.0
> > > > > scanning bus 0 for devices... 1 USB Device(s) found
> > > > > scanning bus 2 for devices... 1 USB Device(s) found
> > > > > scanning bus 1 for devices... unable to get device descriptor 
> > > > > (error=-1)
> > > > > 1 USB Device(s) found
> > > > > scanning bus 3 for devices... 1 USB Device(s) found
> > > > > Hit any key to stop autoboot:  0
> > > > > switch to partitions #0, OK
> > > > > mmc0 is current device
> > > > > Scanning mmc 0:1...
> > > > > Found /extlinux/extlinux.conf
> > > > > Retrieving file: /extlinux/extlinux.conf
> > > > > 494 bytes read in 127 ms (2.9 KiB/s)
> > > > > Ignoring unknown command: ui
> > > > > Ignoring malformed menu command:  autoboot
> > > > > Ignoring malformed menu command:  hidden
> > > > > Ignoring unknown command: totaltimeout
> > > > > Fedora-Xfce-armhfp-23-3 Boot Options.
> > > > > 1:    Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
> > > > > Enter choice: 1:    Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
> > > > > Retrieving file: /initramfs-4.2.3-300.fc23.armv7hl.img
> > > > >     ** ext4fs_devread read error - block
> > > > > Skipping Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl) for failure
> > > > > retrieving
> > > > >     initrd
> > > > > SCRIPT FAILED: continuing...
> > > > > ** Can't read partition table on 0:0 **
> > > > > ** Invalid partition 1 **
> > > > > ** Can't read partition table on 0:0 **
> > > > > ** Invalid partition 1 **
> > > > > ** Can't read partition table on 0:0 **
> > > > > ** Invalid partition 1 **
> > > > > ** Can't read partition table on 0:0 **
> > > > > ** Invalid partition 1 **
> > > > > ** Can't read partition table on 0:0 **
> > > > > ** Invalid partition 1 **
> > > > > scanning bus for devices...
> > > > > Found 0 device(s).
> > > > >
> > > > > SCSI device 0:
> > > > >        Device 0: not available
> > > > >
> > > > > USB device 0: unknown device
> > > > > ethernet@01c50000 Waiting for PHY auto negotiation to complete.... 
> > > > > done
> > > > > Speed: 100, full duplex
> > > > > BOOTP broadcast 1
> > > > > BOOTP broadcast 2
> > > > > BOOTP broadcast 3
> > > > > BOOTP broadcast 4
> > > > > BOOTP broadcast 5
> > > > > BOOTP broadcast 6
> > > > > DHCP client bound to address 192.168.160.23 (5805 ms)
> > > > > *** Warning: no boot file name; using 'C0A8A017.img'
> > > > > Using ethernet@01c50000 device
> > > > > TFTP from server 0.0.0.0; our IP address is 192.168.160.23; sending
> > > > > through gate
> > > > > way 192.168.160.1
> > > > > Filename 'C0A8A017.img'.
> > > > > Load address: 0x42000000
> > > > > Loading: T T T T T T T T T T
> > > > > Retry count exceeded; starting again
> > > > > missing environment variable: pxeuuid
> > > > > Retrieving file: /extlinux/pxelinux.cfg/01-02-c1-08-81-e2-d7
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0A8A017
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0A8A01
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0A8A0
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0A8A
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0A8
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0A
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C0
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/C
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/default-arm-sunxi
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/default-arm
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Retrieving file: /extlinux/pxelinux.cfg/default
> > > > > Speed: 100, full duplex
> > > > > *** ERROR: `serverip' not set
> > > > > Config file not found
> > > > > Speed: 100, full duplex
> > > > > BOOTP broadcast 1
> > > > > DHCP client bound to address 192.168.160.23 (11 ms)
> > > > > Using ethernet@01c50000 device
> > > > > TFTP from server 0.0.0.0; our IP address is 192.168.160.23; sending
> > > > > through gate
> > > > > way 192.168.160.1
> > > > > Filename 'boot.scr.uimg'.
> > > > > Load address: 0x43100000
> > > > > Loading: T T T T T T T T T T
> > > > > Retry count exceeded; starting again
> > > > > sunxi#
> > > > >
> > > > > _______________________________________________
> > > > > arm mailing list
> > > > > arm@xxxxxxxxxxxxxxxxxxxxxxx
> > > > > https://admin.fedoraproject.org/mailman/listinfo/arm
> > _______________________________________________
> > arm mailing list
> > arm@xxxxxxxxxxxxxxxxxxxxxxx
> > https://admin.fedoraproject.org/mailman/listinfo/arm

_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm