It has been a while since I tried any Fedora-23 builds what with a
number of things going on. So seeing the go/nogo, I figured I better
run a test and as you can see it failed (and I tried booting twice with
this image and got the same results):
U-Boot SPL 2015.07 (Sep 12 2015 - 10:46:32)
DRAM: 2048 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
U-Boot 2015.07 (Sep 12 2015 - 10:46:32 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
I2C: ready
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
Setting up a 1024x768 vga console
In: serial
Out: vga
Err: vga
SCSI: SUNXI SCSI INIT
SATA link 0 timeout.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: eth0: ethernet@01c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 1 for devices... unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning bus 3 for devices... 1 USB Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
494 bytes read in 127 ms (2.9 KiB/s)
Ignoring unknown command: ui
Ignoring malformed menu command: autoboot
Ignoring malformed menu command: hidden
Ignoring unknown command: totaltimeout
Fedora-Xfce-armhfp-23-3 Boot Options.
1: Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
Enter choice: 1: Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
Retrieving file: /initramfs-4.2.3-300.fc23.armv7hl.img
** ext4fs_devread read error - block
Skipping Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl) for failure
retrieving
initrd
SCRIPT FAILED: continuing...
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
** Can't read partition table on 0:0 **
** Invalid partition 1 **
scanning bus for devices...
Found 0 device(s).
SCSI device 0:
Device 0: not available
USB device 0: unknown device
ethernet@01c50000 Waiting for PHY auto negotiation to complete.... done
Speed: 100, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
DHCP client bound to address 192.168.160.23 (5805 ms)
*** Warning: no boot file name; using 'C0A8A017.img'
Using ethernet@01c50000 device
TFTP from server 0.0.0.0; our IP address is 192.168.160.23; sending
through gate
way 192.168.160.1
Filename 'C0A8A017.img'.
Load address: 0x42000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
missing environment variable: pxeuuid
Retrieving file: /extlinux/pxelinux.cfg/01-02-c1-08-81-e2-d7
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0A8A017
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0A8A01
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0A8A0
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0A8A
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0A8
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0A
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C0
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/C
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/default-arm-sunxi
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/default-arm
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: /extlinux/pxelinux.cfg/default
Speed: 100, full duplex
*** ERROR: `serverip' not set
Config file not found
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.160.23 (11 ms)
Using ethernet@01c50000 device
TFTP from server 0.0.0.0; our IP address is 192.168.160.23; sending
through gate
way 192.168.160.1
Filename 'boot.scr.uimg'.
Load address: 0x43100000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
sunxi#
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
