On 07/17/2015 01:10 AM, Paul Whalen wrote:
----- Original Message -----
Hi Robert,
On 07/16/2015 10:24 PM, Robert Nelson wrote:
On Thu, Jul 16, 2015 at 8:40 AM, Zamir SUN <zsun@xxxxxxxxxxxxxxxxx> wrote:
Hi team,
I am planning to test Fedora 23 ARM on Beagle Bone black from the early
image. So I downloaded Fedora-Xfce-armhfp-23-20150715-sda.raw.xz from
http://koji.fedoraproject.org/koji/taskinfo?taskID=10371084 and flash it
into a TF card.
During the flashing, I find such error:
= Writing image complete!
= Writing MLO for beaglebone....
dd: failed to open ‘/tmp/root/usr/share/uboot/beaglebone/MLO’: No such
file
or directory
= Writing u-boot.img for beaglebone....
dd: failed to open ‘/tmp/root/usr/share/uboot/beaglebone/u-boot.img’: No
such file or directory
Looks like your task above, missed these crucial boot files..
Thanks for your reminder.
I checked and find that on F22 the file lies in beaglebone, but in F23
the directory is renamed to am335x_boneblack so the fedora-arm-installer
script no longer works.
I will manually finish the steps and continue my testing.
Hi Paul,
There is a new version of the script in rawhide, you can also created a symlink
and use the new name.
There are few others things that might be missing like serial console detection,
so will likely need to add that to the extlinux.conf.
So far in my testing the 4.2 kernel seems to have an issue with mSD, but does find
the eMMC on the beaglebone black. Let us know how it goes for you!
Yes I find it can not boot and just fall back to dracut. I even tried to
switch to another TF card to make sure it is not caused by the card, but
the result is the same. I was planning to have a confirm today and then
saw your reply. So do you have a bug id for this so that I can post my
log there?
And here is my log http://paste.fedoraproject.org/245362/
Zamir
Paul
= Installation Complete! Insert into the beaglebone and boot.
$
And then I just try to boot Beagle Bone Black from the image and find it
do
not work. The serial output is as following:
U-Boot SPL 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img
U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
** File not found uEnv.txt **
Checking if uenvcmd is set ...
uenvcmd was not defined in uEnv.txt ...
gpio: pin 56 (gpio 56) value is 0
gpio: pin 55 (gpio 55) value is 0
gpio: pin 54 (gpio 54) value is 0
mmc1(part 0) is current device
then it boot to my system on emmc. So am I wrong in some steps? Or the
image
just can not boot up on Beagle Bone Black by design?
That old factory bootloader in the eMMC doesn't know about how to deal
with newer extlinux image's.
Regards,
--
Zamir SUN
zsun@xxxxxxxxxxxxxxxxx
zsun in #fedora-zh #openshift on freenode.net
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
--
Zamir SUN
zsun@xxxxxxxxxxxxxxxxx
zsun in #fedora-zh #openshift on freenode.net
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
