Re: Getting FC21/arm to boot on beaglebone black/beagle XM/beagleboard/Mele A2000

[Frans Meulenbroeks <fransmeulenbroeks@xxxxxxxxx>]

Apparently this did not make it to the list. Guess this is because my list membership was not approved yet then.

2015-01-25 11:30 GMT+01:00 Frans Meulenbroeks <fransmeulenbroeks@xxxxxxxxx>:

Hi,

I was trying to see which of the ARM boards I had lying around would boot FC21.

I followed these instructions:

http://fedoraproject.org/wiki/Architectures/ARM/F21/Installation

With these I managed to boot FC21 successfully on

- orange pi (A20, similar to banana pi)

- pandaboard

- beaglebone white

However, although according to the instructions the same MLO and u-boot are to be used for beaglebone black, it does not boot there, although the very same card works with beaglebone white.

I have added a serial port to the BBB and captured the boot log. See at the end of this message.

Anyone an idea what is wrong?

While at it:

According to http://fedoraproject.org/wiki/Architectures/ARM/F21/Installation/Hardware_Status beagleboard XM also works but there is no u-boot data in the image for XM. Suggestions for this?

And I noticed the u-boot dir also contains a u-boot for the Mele A1000. I wanted to try that one the A2000 which is identical hw, but it did not work (and I do not have serial for the A2000)

Anyone a suggestion.

I also noticed beagleboard being in the uboot folder but it was not listed on the pages referred to above, Should this work?

Lastly I noticed in the image a boot.scr and a boot.cmd file (slightly different).
These seem to be some generic code to boot into a number of boards, but I could not find instructions how to use/invoke this. Is that going to be useful for me? How should I use it?

Thanks, Frans

PS: subscription to the list is pending approval, please also reply directly. Thanks.

---- boot log from beaglebone black ----

U-Boot SPL 2013.04-dirty (May 06 2013 - 16:12:47)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img


U-Boot 2013.04-dirty (May 06 2013 - 16:12:47)

I2C:   ready
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  No NAND device found!!!
0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
** File not found uEnv.txt **
gpio: pin 55 (gpio 55) value is 1
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **

_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm