I've had another go at installing F21 on my utilite, but am still not
having any luck.
This is the pro version, with the SSD.
I've inserted my SD card, and written the F21 image and the u-boot image
from
http://utilite-computer.com/download/utilite/u-boot/utilite-updater.tar.bz2
to it:
dd if=Fedora-Minimal-armhfp-21_Alpha-1-sda.raw of=/dev/mmcblk0
dd if=cm-fx6-firmware of=/dev/mmcblk0 bs=1K skip=1 seek=1 oflag=dsync
But I'm obviously missing some u-boot configuration, since on reboot it
starts booting from the sd but then just switches back to the SSD:
U-Boot SPL 2014.04-cm-fx6-1.1 (Jul 07 2014 - 11:11:21)
Booting from MMC
U-Boot 2014.04-cm-fx6-1.2 (Aug 24 2014 - 14:05:41)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: WDOG
I tried to force a manual boot from the SD:
CM-FX6 # ext2load mmc 2 0x10800000 uImage-3.16.1-301.fc21.armv7hl
5460752 bytes read in 338 ms (15.4 MiB/s)
CM-FX6 # ext2load mmc 2 0x11000000 uInitrd-3.16.1-301.fc21.armv7hl
29206069 bytes read in 1372 ms (20.3 MiB/s)
but that failed almost immediately:
CM-FX6 # bootm 0x10800000 0x11000000
## Booting kernel from Legacy Image at 10800000 ...
Image Name: 3.16.1-301.fc21.armv7hl
Created: 2014-09-16 3:19:49 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5460688 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 11000000 ...
Image Name: initramfs
Created: 2014-09-16 3:19:50 UTC
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 29206005 Bytes = 27.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... data abort
pc : [<8ff872e0>] lr : [<8ff5c724>]
sp : 8fd53da0 ip : 00000000 fp : 8ffa1638
r10: 00000000 r9 : 8fd53f28 r8 : 8fd598ac
r7 : 00000000 r6 : 00008000 r5 : 0000070f r4 : 00000000
r3 : 00000000 r2 : 005352d0 r1 : 10800040 r0 : 00008000
Flags: Nzcv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
I've also tried running the boot.scr that's on the F21 boot partition:
CM-FX6 # ext2load mmc 2 0x10800000 boot.scr
22564 bytes read in 93 ms (236.3 KiB/s)
CM-FX6 # imi 0x10800000
## Checking Image at 10800000 ...
Legacy image found
Image Name: a-b-c on Mon Sep 15 23:28:19 EDT
Created: 2014-09-16 3:28:19 UTC
Image Type: ARM Linux Script (uncompressed)
Data Size: 22500 Bytes = 22 KiB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 22492 Bytes = 22 KiB
Verifying Checksum ... OK
CM-FX6 # source 0x10800000
## Executing script at 10800000
Welcome to a-b-c 0.63.
Could not successfully auto-detect system type.
You may need to set u_k_addr, u_ramfs_addr, u_dtb_addr, and u_dtb
Will scan for kernels on mmc usb scsi sata ide, using ext2 fat
filesystems with bootm
Starting menu init....
Failed to auto-boot
No value for u_dtb. Use klist and dtblist to select.
a-b-c main menu
---------------
run clist: for a list of known board configurations.
run klist: for a list of kernels.
run dtblist: for a list of dtbs.
run single: for single user target on boot.
run rescue: for rescue target on boot.
run graphical: for graphical target on boot.
run debug: for verbose debug boot.
run normal: for default systemd boot target (default).
run showdefs: for current defaults.
boot or run bootcmd: boot with currently configured parameters.
Enter command from the above list.
CM-FX6 # run clist
Board Configuration List
------------------------
syntax error
## Error: "catX" not defined
c1:
syntax error
## Error: "catX" not defined
c2:
syntax error
## Error: "catX" not defined
c3:
syntax error
## Error: "catX" not defined
c4:
syntax error
## Error: "catX" not defined
c5:
syntax error
## Error: "catX" not defined
c6:
syntax error
## Error: "catX" not defined
c7:
syntax error
## Error: "catX" not defined
c8:
syntax error
## Error: "catX" not defined
c9:
syntax error
## Error: "catX" not defined
c10:
syntax error
## Error: "catX" not defined
c11:
syntax error
## Error: "catX" not defined
c12:
syntax error
## Error: "catX" not defined
c13:
syntax error
## Error: "catX" not defined
c14:
syntax error
## Error: "catX" not defined
c15:
syntax error
## Error: "catX" not defined
c16:
syntax error
## Error: "catX" not defined
c17:
syntax error
## Error: "catX" not defined
c18:
syntax error
## Error: "catX" not defined
c19:
Type "run cX" where X is the board configuration number to use.
CM-FX6 #
From the file source I remembered that c10 is utilitie, so I tried:
CM-FX6 # run c10
Configuring for utilite
Configuring for imx
The following configuration values are defined:
u_k_addr: 0x14000000
u_k_addr: 0x14000000
u_ramfs_addr: 0x32000000
u_dtb_addr: 0x12000000
u_iodevs: sata mmc usb
u_iodevs: sata mmc usb
u_fs: ext2
u_devpart: 0:1 0:2 1:1 1:2
u_boot: bootm
u_root: UUID=c078beec-18b2-44ae-aac5-e6fc275b45c5
u_dtb:
skip_dtb: 1 (null means a dtb will be loaded)
pass_dtb: (null means no bootarg passed)
u_extraargs: console=ttymxc3,115200,115200
CM-FX6 # run klist |
|
Kernel List |
----------- |
syntax error |
## Error: "catX" not defined |
syntax error |
## Error: "catX" not defined |
k1: for |
(Currently selected: k: ) |
|
Type "run kX" where X is the kernel number to use. |
CM-FX6 # run k1 |
syntax error
## Error: "catX" not defined
Using kernel k1 ().
CM-FX6 #
Looks like the syntax errors all come from this:
setenv catX "setenv catout \\\'$$catin\\\'"
I've tried a "boot" anyway at that point, but that failed with lots of
errors for sata 0, sata 1, mmc0, mmc1, usb0, usb1; no messages at all
about mmc2.
Any hints would be appreciated.
J.
_______________________________________________
arm mailing list
arm@xxxxxxxxxxxxxxxxxxxxxxx
https://admin.fedoraproject.org/mailman/listinfo/arm
