Hi.. I've just upgraded my kernel to 2.6.24 which includes ALSA 1.0.15.
There is some alsa-relative line in my current dmesg:
hda_intel: azx_get_response timeout, switching to polling mode: last
cmd=0x00cb8000
This is on-board nVidia HDA audio on MSI laptop.
00:10.1 Audio device [0403]: nVidia Corporation MCP51 High Definition Audio [10de:026c] (rev a2)
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:3fdf]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fdfb8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00: de 10 6c 02 06 00 b0 00 a2 00 03 04 00 00 80 00
10: 00 80 fb fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 df 3f
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 02 05
I don't know, is it good or bad. Sounds works (internal speaker as well
as 3.5mm audio jack). So I think, that I can just ignore it. Am I right?
PS. Full dmesg output for 2.6.24 kernel is attached.
Thanks
--
WBR, Dmitry
Linux version 2.6.24 (dion@laptop) (gcc version 4.2.3 20080114 (prerelease) (Debian 4.2.2-7)) #2 SMP PREEMPT Sun Jan 27 12:38:27 EET 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffd0000 (usable)
BIOS-e820: 000000007ffd0000 - 000000007ffde000 (ACPI data)
BIOS-e820: 000000007ffde000 - 0000000080000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 524240) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 524240
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 524240
On node 0 totalpages: 524240
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2303 pages used for memmap
HighMem zone: 292561 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F8A70, 0014 (r0 M S I )
ACPI: RSDT 7FFD0000, 0040 (r1 MSI_NB MEGABOOK 5000717 MSFT 97)
ACPI: FACP 7FFD0200, 0084 (r2 MSI_NB 1635X 5000717 MSFT 97)
ACPI: DSDT 7FFD05C0, 4A52 (r1 M S I 1635X 4162004 INTL 20051117)
ACPI: FACS 7FFDE000, 0040
ACPI: APIC 7FFD0390, 0070 (r1 MSI_NB OEMAPIC 5000717 MSFT 97)
ACPI: MCFG 7FFD0400, 003C (r1 MSI_NB OEMMCFG 5000717 MSFT 97)
ACPI: SLIC 7FFD0440, 0176 (r1 MSI_NB MEGABOOK 5000717 MSFT 97)
ACPI: OEMB 7FFDE040, 0071 (r1 MSI_NB AMI_OEM 5000717 MSFT 97)
ACPI: HPET 7FFD5020, 0038 (r1 MSI_NB OEMHPET0 5000717 MSFT 97)
ACPI: SSDT 7FFD5060, 01EC (r1 A M I POWERNOW 1 AMD 1)
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:8 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520145
Kernel command line: root=/dev/mapper/laptop-deb_root resume=swap:/dev/mapper/laptop-swap agp=off ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1607.378 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2071768k/2096960k available (2467k kernel code, 23812k reserved, 874k data, 360k init, 1179456k highmem)
virtual kernel memory layout:
fixmap : 0xffe15000 - 0xfffff000 (1960 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0449000 - 0xc04a3000 ( 360 kB)
.data : 0xc0368ea6 - 0xc0443a04 ( 874 kB)
.text : 0xc0100000 - 0xc0368ea6 (2467 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet clockevent registered
Calibrating delay using timer specific routine.. 3217.43 BogoMIPS (lpj=6434878)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Core 0
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3214.64 BogoMIPS (lpj=6429294)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Core 1
AMD C1E detected late. Force timer broadcast.
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
Total of 2 processors activated (6432.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 2 CPUs
net_namespace: 64 bytes
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
ACPI: EC: GPE = 0x26, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 17) *10
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 18) *10
ACPI: PCI Interrupt Link [LNEB] (IRQs 19) *5
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 21) *7
ACPI: PCI Interrupt Link [LUB2] (IRQs 21) *14
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 23) *11
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LPMU] (IRQs 20) *11
ACPI: PCI Interrupt Link [LSA0] (IRQs 22) *10
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
ACPI: RTC can wake from S4
Time: hpet clocksource has been installed.
Clockevents: could not switch to one-shot mode: lapic is not functional.
Could not switch to high resolution mode on CPU 0
Clockevents: could not switch to one-shot mode: lapic is not functional.
Could not switch to high resolution mode on CPU 1
system 00:07: iomem range 0xfefe0000-0xfefe01ff has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x80f has been reserved
system 00:08: ioport range 0x4000-0x407f has been reserved
system 00:08: ioport range 0x4080-0x40ff has been reserved
system 00:08: ioport range 0x4400-0x447f has been reserved
system 00:08: ioport range 0x4480-0x44ff has been reserved
system 00:08: ioport range 0x4800-0x487f has been reserved
system 00:08: ioport range 0x4880-0x48ff has been reserved
system 00:08: ioport range 0x2000-0x207f has been reserved
system 00:08: ioport range 0x2080-0x20ff has been reserved
system 00:08: iomem range 0x0-0x0 could not be reserved
system 00:08: iomem range 0xfee01000-0xfeefffff could not be reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0x7fffffff could not be reserved
system 00:0c: iomem range 0xfec00000-0xffffffff could not be reserved
PCI: Bridge: 0000:00:02.0
IO window: b000-bfff
MEM window: f8c00000-f8cfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
IO window: c000-cfff
MEM window: f8d00000-f94fffff
PREFETCH window: bbf00000-bdefffff
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: f9500000-fd5fffff
PREFETCH window: bdf00000-ddefffff
PCI: Bus 6, cardbus bridge: 0000:05:04.0
IO window: 0000d000-0000d0ff
IO window: 0000d400-0000d4ff
PREFETCH window: 88000000-8bffffff
MEM window: 8c000000-8fffffff
PCI: Bridge: 0000:00:10.0
IO window: d000-dfff
MEM window: fd600000-fdefffff
PREFETCH window: ddf00000-dfefffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 17
ACPI: PCI Interrupt 0000:05:04.0[A] -> Link [LNKC] -> GSI 17 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2388k freed
audit: initializing netlink socket (disabled)
audit(1201435520.620:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.9)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:04:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Loading iSCSI transport class v2.0-724.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
cpuidle: using governor ladder
cpuidle: using governor menu
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI No-Shortcut mode
Freeing unused kernel memory: 360k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LSA0] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xe800 ctl 0xe480 bmdma 0xe000 irq 17
ata2: SATA max UDMA/133 cmd 0xe400 ctl 0xe080 bmdma 0xe008 irq 17
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-6: TOSHIBA MK1032GSX, AS021J, max UDMA/100
ata1.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1032GS AS02 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: Thermal Zone [THRM] (49 C)
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@xxxxxxxxxx
TuxOnIce: Normal swapspace found.
TuxOnIce: Normal swapspace found.
ReiserFS: dm-1: found reiserfs format "3.6" with standard journal
ReiserFS: dm-1: using ordered data mode
ReiserFS: dm-1: journal params: device dm-1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-1: checking transaction log (dm-1)
ReiserFS: dm-1: Using r5 hash to sort names
input: PC Speaker as /devices/platform/pcspkr/input/input1
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:01:00.0 to 64
r8169 0000:01:00.0: no MSI. Back to INTx.
eth0: RTL8168b/8111b at 0xf89c0000, 00:19:db:39:27:f0, XID 38000000 IRQ 18
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x6000
Yenta: CardBus bridge found at 0000:05:04.0 [1462:3fdf]
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
pata_amd 0000:00:0d.0: version 0.3.10
PCI: Setting latency timer of device 0000:00:0d.0 to 64
scsi2 : pata_amd
scsi3 : pata_amd
ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata3: port disabled. ignoring.
input: Power Button (FF) as /devices/virtual/input/input2
Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#05) from #06 to #09
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
cs: IO port probe 0xd000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xfd600000 - 0xfdefffff
pcmcia: parent PCI bridge Memory window: 0xddf00000 - 0xdfefffff
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/virtual/input/input3
ACPI: Lid Switch [LID0]
input: Sleep Button (CM) as /devices/virtual/input/input4
input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio2/input/input5
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /devices/virtual/input/input6
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Power Button (CM) [PWRB]
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:02/LNXVIDEO:00/input/input7
ata4.00: ATAPI: Optiarc DVD RW AD-7530A, EX32, max UDMA/33
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Battery Slot [BAT1] (battery present)
ata4.00: configured for UDMA/33
scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7530A EX32 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUB2] -> GSI 21 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 19, io mem 0xfdfbfc00
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
udev: renamed network interface eth0 to lan0
ACPI: PCI Interrupt 0000:05:04.4[A] -> Link [LNKC] -> GSI 17 (level, low) -> IRQ 16
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[fdeff000-fdeff7ff] Max Packet=[2048] IR/IT contexts=[8/8]
sdhci: SDHCI controller found at 0000:05:04.2 [1217:7120] (rev 1)
ACPI: PCI Interrupt 0000:05:04.2[A] -> Link [LNKC] -> GSI 17 (level, low) -> IRQ 16
sdhci:slot0: Unknown controller version (16). You may experience problems.
mmc0: SDHCI at 0xfdefe400 irq 16 PIO
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
ACPI: PCI Interrupt 0000:05:09.0[A] -> Link [LNKA] -> GSI 16 (level, low) -> IRQ 20
phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80
phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff
phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c.
phy0: Selected rate control algorithm 'simple'
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 23 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:10.1 to 64
usb 1-1: new high speed USB device using ehci_hcd and address 2
mice: PS/2 mouse device common for all mice
usb 1-1: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUB0] -> GSI 21 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 19, io mem 0xfdfbe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
usb 1-8: new high speed USB device using ehci_hcd and address 4
usb 1-8: configuration #1 chosen from 1 choice
hub 1-8:1.0: USB hub found
hub 1-8:1.0: 4 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 3:0:0:0: Attached scsi generic sg1 type 5
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00dc1000c35b1a01]
usb 2-7: new full speed USB device using ohci_hcd and address 2
usb 2-7: configuration #1 chosen from 1 choice
usb 1-8.1: new low speed USB device using ehci_hcd and address 5
usb 1-8.1: configuration #1 chosen from 1 choice
usb 1-8.2: new low speed USB device using ehci_hcd and address 6
hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x00cb8000
usb 1-8.2: configuration #1 chosen from 1 choice
cdc_acm 2-7:1.0: ttyACM0: USB ACM device
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver hiddev
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.1/1-8.1:1.0/input/input8
input,hidraw0: USB HID v1.10 Keyboard [Chicony USB Keyboard] on usb-0000:00:0b.1-8.1
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.1/1-8.1:1.1/input/input9
input,hiddev96,hidraw1: USB HID v1.10 Device [Chicony USB Keyboard] on usb-0000:00:0b.1-8.1
input: Acrox USB & PS/2 Mouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.2/1-8.2:1.0/input/input10
input,hidraw2: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:00:0b.1-8.2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
loop: module loaded
ReiserFS: dm-3: found reiserfs format "3.6" with standard journal
ReiserFS: dm-3: using ordered data mode
ReiserFS: dm-3: journal params: device dm-3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-3: checking transaction log (dm-3)
ReiserFS: dm-3: Using r5 hash to sort names
ReiserFS: dm-4: found reiserfs format "3.6" with standard journal
ReiserFS: dm-4: using ordered data mode
ReiserFS: dm-4: journal params: device dm-4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-4: checking transaction log (dm-4)
ReiserFS: dm-4: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 3145720k swap on /dev/mapper/laptop-swap. Priority:-1 extents:1 across:3145720k
r8169: lan0: link up
r8169: lan0: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-52 processors (2 cpu cores) (version 2.20.00)
powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13
powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e
warning: process `nginx' used the deprecated sysctl system call with 1.33.
Clocksource tsc unstable (delta = -232030515 ns)
lan0: no IPv6 routers present
ACPI: EC: missing OBF confirmation, don't expect it any longer.
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
powernow-k8: ignoring illegal change in lo freq table-0 to 0x0
powernow-k8: transition frequency failed
hub 1-8:1.0: suspend error -16
cdc_acm 2-7:1.0: no suspend for driver cdc_acm?
cdc_acm 2-7:1.1: no suspend for driver cdc_acm?
hub 1-0:1.0: suspend error -16
Linux agpgart interface v0.102
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 18
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNEA] -> GSI 18 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:04:00.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 169.07 Thu Dec 13 18:42:56 PST 2007
cdc_acm 2-7:1.0: no resume for driver cdc_acm?
cdc_acm 2-7:1.1: no resume for driver cdc_acm?
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
tun0: Disabled Privacy Extensions
usb 1-8: USB disconnect, address 4
usb 1-8.1: USB disconnect, address 5
usb 1-8.2: USB disconnect, address 6
usb 1-8: new high speed USB device using ehci_hcd and address 7
usb 1-8: configuration #1 chosen from 1 choice
hub 1-8:1.0: USB hub found
hub 1-8:1.0: 4 ports detected
usb 1-8.1: new low speed USB device using ehci_hcd and address 8
usb 1-8.1: configuration #1 chosen from 1 choice
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.1/1-8.1:1.0/input/input11
input,hidraw0: USB HID v1.10 Keyboard [Chicony USB Keyboard] on usb-0000:00:0b.1-8.1
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.1/1-8.1:1.1/input/input12
input,hiddev96,hidraw1: USB HID v1.10 Device [Chicony USB Keyboard] on usb-0000:00:0b.1-8.1
usb 1-8.2: new low speed USB device using ehci_hcd and address 9
usb 1-8.2: configuration #1 chosen from 1 choice
input: Acrox USB & PS/2 Mouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.2/1-8.2:1.0/input/input13
input,hidraw2: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:00:0b.1-8.2
usb 1-2: new high speed USB device using ehci_hcd and address 10
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver libusual
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 10
usb-storage: waiting for device to settle before scanning
scsi 4:0:0:0: Direct-Access Maxtor 6 L300R0 1G20 PQ: 0 ANSI: 2 CCS
sd 4:0:0:0: [sdb] 586114704 512-byte hardware sectors (300091 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 38 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sd 4:0:0:0: [sdb] 586114704 512-byte hardware sectors (300091 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 38 00 00
sd 4:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1 sdb2
sd 4:0:0:0: [sdb] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
ReiserFS: dm-7: found reiserfs format "3.6" with standard journal
ReiserFS: dm-7: using ordered data mode
ReiserFS: dm-7: journal params: device dm-7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-7: checking transaction log (dm-7)
ReiserFS: dm-7: Using r5 hash to sort names
ReiserFS: dm-8: found reiserfs format "3.6" with standard journal
ReiserFS: dm-8: using ordered data mode
ReiserFS: dm-8: journal params: device dm-8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-8: checking transaction log (dm-8)
ReiserFS: dm-8: Using r5 hash to sort names
usb 1-8: USB disconnect, address 7
usb 1-8.1: USB disconnect, address 8
usb 1-8.2: USB disconnect, address 9
usb 1-8: new high speed USB device using ehci_hcd and address 11
usb 1-8: configuration #1 chosen from 1 choice
hub 1-8:1.0: USB hub found
hub 1-8:1.0: 4 ports detected
usb 1-8.1: new low speed USB device using ehci_hcd and address 12
usb 1-8.1: configuration #1 chosen from 1 choice
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.1/1-8.1:1.0/input/input14
input,hidraw0: USB HID v1.10 Keyboard [Chicony USB Keyboard] on usb-0000:00:0b.1-8.1
input: Chicony USB Keyboard as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.1/1-8.1:1.1/input/input15
input,hiddev96,hidraw1: USB HID v1.10 Device [Chicony USB Keyboard] on usb-0000:00:0b.1-8.1
usb 1-8.2: new low speed USB device using ehci_hcd and address 13
usb 1-8.2: configuration #1 chosen from 1 choice
input: Acrox USB & PS/2 Mouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-8/1-8.2/1-8.2:1.0/input/input16
input,hidraw2: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:00:0b.1-8.2
NET: Registered protocol family 17
i2c /dev entries driver
Attachment:
signature.asc
Description: Digital signature
------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________ Alsa-user mailing list Alsa-user@xxxxxxxxxxxxxxxxxxxxx https://lists.sourceforge.net/lists/listinfo/alsa-user
