From: Dave Chinner <dchinner@xxxxxxxxxx>
Test 227 (fsr test) creates fragmented fre space by doing lots of
small writes to sparse offsets ni a file. This seeks the disk heads
around a lot writing data. We don't need to write data - just
trigger allocation. Hence use preallocation instead of data writes
and run at allocation speed rather than data write speed.
Signed-off-by: Dave Chinner <dchinner@xxxxxxxxxx>
---
227 | 46 +++++++++++++++++++++++++++++++++-------------
1 file changed, 33 insertions(+), 13 deletions(-)
diff --git a/227 b/227
index cb7fa70..dfcb1a5 100755
--- a/227
+++ b/227
@@ -52,6 +52,8 @@ _supported_fs xfs
_supported_os Linux
_require_scratch
+rm -f $seq.full
+
[ "$XFS_FSR_PROG" = "" ] && _notrun "xfs_fsr not found"
# create freespace holes of 1-3 blocks in length
@@ -62,26 +64,41 @@ _require_scratch
# (say 5 extents) and lots of variations around that dependent on the
# number of attributes in the files being defragmented.
#
+# We have to make sure there are enough free inodes for the test to
+# pass without needing to allocate new clusters during the test.
+# With such fragemented free space, that will fail.
+#
fragment_freespace()
{
_file="$SCRATCH_MNT/not_free"
+ _dir="$SCRATCH_MNT/saved"
- for i in `seq 0 1 10000`; do
- echo foo > $_file.$i
+ # allocate inode space
+ mkdir -p $_dir
+ for i in `seq 0 1 1000`; do
+ touch $_file.$i
done
- sync
-
- for i in `seq 0 2 10000`; do
- rm -f $_file.$i
+ for i in `seq 0 63 1000`; do
+ mv $_file.$i $_dir
done
- for i in `seq 0 7 10000`; do
+ for i in `seq 0 1 1000`; do
rm -f $_file.$i
done
+
+ $XFS_IO_PROG -fs -c "resvsp 0 40000k" $_file > /dev/null 2>&1
+
+ for i in `seq 0 8 40000`; do
+ $XFS_IO_PROG -f -c "unresvsp ${i}k 4k" $_file \
+ > /dev/null 2>&1
+ done
+ for i in `seq 0 28 40000`; do
+ $XFS_IO_PROG -f -c "unresvsp ${i}k 4k" $_file \
+ > /dev/null 2>&1
+ done
sync
# and now use up all the remaining extents larger than 3 blocks
- dd if=/dev/zero of=$_file.large bs=4k count=1024 > /dev/null 2>&1
- sync
+ $XFS_IO_PROG -fs -c "resvsp 0 4m" $_file.large > /dev/null 2>&1
}
create_attrs()
@@ -93,11 +110,12 @@ create_attrs()
create_data()
{
+ size=`expr \( $1 + 1 \) \* 4096`
+ $XFS_IO_PROG -f -c "truncate $size" $2 > /dev/null 2>&1
for foo in `seq $1 -1 0`; do
let offset=$foo*4096
- $XFS_IO_PROG -f -c "pwrite $offset 4096" -c "fsync" $2 > /dev/null 2>&1
+ $XFS_IO_PROG -f -c "resvsp $offset 4096" $2 > /dev/null 2>&1
done
- xfs_bmap -vp $2
}
# create the designated file with a certain number of attributes and a certain
@@ -113,7 +131,7 @@ create_target_attr_first()
target=$3
rm -f $target
- echo > $target
+ touch $target
create_attrs $nattrs $target
create_data $file_blocks $target
}
@@ -131,7 +149,7 @@ create_target_attr_last()
target=$3
rm -f $target
- echo > $target
+ touch $target
create_data $file_blocks $target
create_attrs $nattrs $target
}
@@ -176,11 +194,13 @@ for n in `seq 4 1 12`; do
for j in `seq 5 1 20`; do
create_target_attr_first $i $j $targ.$i.$j >> $seq.full 2>&1
done
+ xfs_bmap -vp $targ.$i.* >> $seq.full 2>&1
FSRXFSTEST=true xfs_fsr -d -v -C $n $targ.$i.* >> $seq.full 2>&1
xfs_bmap -vp $targ.$i.* >> $seq.full 2>&1
for j in `seq 5 1 20`; do
create_target_attr_last $i $j $targ.$i.$j >> $seq.full 2>&1
done
+ xfs_bmap -vp $targ.$i.* >> $seq.full 2>&1
FSRXFSTEST=true xfs_fsr -d -v -C $n $targ.$i.* >> $seq.full 2>&1
xfs_bmap -vp $targ.$i.* >> $seq.full 2>&1
done
--
1.7.10
_______________________________________________
xfs mailing list
xfs@xxxxxxxxxxx
http://oss.sgi.com/mailman/listinfo/xfs
