Hello, I realize I'm ignoring the very first thing your log file says, which is to try a newer version before reporting problems. I am running XFree86 Version 4.2.0, which is bundled with Red Hat 7.3, an "old" but very stable release. This version of XFree86 has run without incident on this machine almost continuously for two years now, which is why the recent crash was so surprising. I am ignoring your directive because it is essential that the X installation on this machine be rock-solid; I cannot afford to try a newer release only to find, in another year, that the same (highly intermittent) bug is still in place and has caused another crash. If I can't be assured that the bug is fixed, I will have to look for an alternate X server. So I am hoping that from the attached log file, someone can identify the cause of the crash and tell me either "Yes, this bug has been discovered and is fixed as of version 4.foo of XFree86" or "No, this bug has not been discovered yet but can be fixed now with this information." I don't see any obvious error message in the log other than "Caught signal 11" so I was unable to google for further details about this problem. The crash happened on the evening of August 31, 2005. X had been running since June 29 (the machine was last booted on June 28), a relatively short time for this machine. (Typical uptime is well over 100 days.) I log in on a tty and start X with the "startx" command rather than running xdm or similar. I use fvwm as my window manager, and I was not doing anything tricky or unusual at the time of the crash - I was trying to select a drop-down menu on a web page. X disappeared very quickly without any warning that something bad was about to happen, and I was dropped back to the Linux tty with the "Fatal server error" message. I monitor available swap space fairly regularly and the last time I checked before the crash there was plenty. I can give you whatever other information you might need to determine the cause of this crash, but offhand I don't know what else might be relevant and I don't want to make this message so long that no one bothers reading it. :-) Thanks for any information or insight you can give me, --Dave
XFree86 Version 4.2.0 (Red Hat Linux release: 4.2.0-8) / X Window System (protocol Version 11, revision 0, vendor release 6600) Release Date: 23 January 2002 If the server is older than 6-12 months, or if your card is newer than the above date, look for a newer version before reporting problems. (See http://www.XFree86.Org/) Build Operating System: Linux 2.4.17-0.13smp i686 [ELF] Build Host: daffy.perf.redhat.com Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/XFree86.0.log", Time: Wed Jun 29 22:40:02 2005 (==) Using config file: "/etc/X11/XF86Config-4" (==) ServerLayout "Anaconda Configured" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (**) | |-->Device "S3 Trio3D" (**) |-->Input Device "Mouse0" (**) |-->Input Device "Keyboard0" (**) Option "XkbRules" "xfree86" (**) XKB: rules: "xfree86" (**) Option "XkbModel" "pc105" (**) XKB: model: "pc105" (**) Option "XkbLayout" "us" (**) XKB: layout: "us" (==) Keyboard: CustomKeycode disabled (**) FontPath set to "unix/:7100" (**) RgbPath set to "/usr/X11R6/lib/X11/rgb" (==) ModulePath set to "/usr/X11R6/lib/modules" (--) using VT number 7 (II) Open APM successful (II) Module ABI versions: XFree86 ANSI C Emulation: 0.1 XFree86 Video Driver: 0.5 XFree86 XInput driver : 0.3 XFree86 Server Extension : 0.1 XFree86 Font Renderer : 0.3 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Module bitmap: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.3 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11R6/lib/modules/libpcidata.a (II) Module pcidata: vendor="The XFree86 Project" compiled for 4.2.0, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.5 (II) PCI: Probing config type using method 1 (II) PCI: Config type is 1 (II) PCI: stages = 0x03, oldVal1 = 0x8000180c, mode1Res1 = 0x80000000 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 8086,7190 card 0000,0000 rev 02 class 06,00,00 hdr 00 (II) PCI: 00:01:0: chip 8086,7191 card 0000,0000 rev 02 class 06,04,00 hdr 01 (II) PCI: 00:02:0: chip 8086,7110 card 0000,0000 rev 02 class 06,01,00 hdr 80 (II) PCI: 00:02:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00 (II) PCI: 00:02:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00 (II) PCI: 00:02:3: chip 8086,7113 card 0000,0000 rev 02 class 06,80,00 hdr 00 (II) PCI: 00:03:0: chip 8086,1229 card 1014,00d7 rev 05 class 02,00,00 hdr 00 (II) PCI: 00:12:0: chip 1101,9400 card 9292,0202 rev 01 class 01,00,00 hdr 00 (II) PCI: 01:01:0: chip 5333,8904 card 1014,00db rev 01 class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) LoadModule: "scanpci" (II) Loading /usr/X11R6/lib/modules/libscanpci.a (II) Module scanpci: vendor="The XFree86 Project" compiled for 4.2.0, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.5 (II) UnloadModule: "scanpci" (II) Unloading /usr/X11R6/lib/modules/libscanpci.a (II) Host-to-PCI bridge: (II) PCI-to-ISA bridge: (II) PCI-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x88 (VGA_EN is set) (II) Bus 1 I/O range: (II) Bus 1 non-prefetchable memory range: [0] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B] (II) Bus 1 prefetchable memory range: (II) Bus -1: bridge is at (0:2:0), (0,-1,0), BCTRL: 0x08 (VGA_EN is set) (II) Bus -1 I/O range: (II) Bus -1 non-prefetchable memory range: (II) Bus -1 prefetchable memory range: (--) PCI:*(1:1:0) S3 Trio3D rev 1, Mem @ 0xf4000000/26, BIOS @ 0x000c0000/16 (II) Addressable bus resource ranges are [0] -1 0x00000000 - 0xffffffff (0x0) MX[B] [1] -1 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0x00000000 - 0x000000ff (0x100) IX[B] (II) Active PCI resource ranges: [0] -1 0xf3eff000 - 0xf3efffff (0x1000) MX[B] [1] -1 0xf3f00000 - 0xf3ffffff (0x100000) MX[B] [2] -1 0xf3dff000 - 0xf3dfffff (0x1000) MX[B] [3] -1 0xec000000 - 0xefffffff (0x4000000) MX[B] [4] -1 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [5] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B](B) [6] -1 0x00007800 - 0x000078ff (0x100) IX[B] [7] -1 0x00007c60 - 0x00007c7f (0x20) IX[B] [8] -1 0x0000ff00 - 0x0000ff1f (0x20) IX[B] [9] -1 0x0000fff0 - 0x0000ffff (0x10) IX[B] (II) Active PCI resource ranges after removing overlaps: [0] -1 0xf3eff000 - 0xf3efffff (0x1000) MX[B] [1] -1 0xf3f00000 - 0xf3ffffff (0x100000) MX[B] [2] -1 0xf3dff000 - 0xf3dfffff (0x1000) MX[B] [3] -1 0xec000000 - 0xefffffff (0x4000000) MX[B] [4] -1 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [5] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B](B) [6] -1 0x00007800 - 0x000078ff (0x100) IX[B] [7] -1 0x00007c60 - 0x00007c7f (0x20) IX[B] [8] -1 0x0000ff00 - 0x0000ff1f (0x20) IX[B] [9] -1 0x0000fff0 - 0x0000ffff (0x10) IX[B] (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0xf3eff000 - 0xf3efffff (0x1000) MX[B] [6] -1 0xf3f00000 - 0xf3ffffff (0x100000) MX[B] [7] -1 0xf3dff000 - 0xf3dfffff (0x1000) MX[B] [8] -1 0xec000000 - 0xefffffff (0x4000000) MX[B] [9] -1 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [10] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B](B) [11] -1 0x0000ffff - 0x0000ffff (0x1) IX[B] [12] -1 0x00000000 - 0x000000ff (0x100) IX[B] [13] -1 0x00007800 - 0x000078ff (0x100) IX[B] [14] -1 0x00007c60 - 0x00007c7f (0x20) IX[B] [15] -1 0x0000ff00 - 0x0000ff1f (0x20) IX[B] [16] -1 0x0000fff0 - 0x0000ffff (0x10) IX[B] (II) LoadModule: "GLcore" (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Module GLcore: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.1 (II) LoadModule: "dbe" (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a (II) Module dbe: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.1 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a (II) Module extmod: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.1 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension FontCache (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) LoadModule: "fbdevhw" (II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a (II) Module fbdevhw: vendor="The XFree86 Project" compiled for 4.2.0, module version = 0.0.2 ABI class: XFree86 Video Driver, version 0.5 (II) LoadModule: "dri" (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a (II) Module dri: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.1 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a (II) Module drm: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.1 (II) Loading extension XFree86-DRI (II) LoadModule: "glx" (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a (II) Module glx: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.1 (II) Loading sub module "GLcore" (II) LoadModule: "GLcore" (II) Reloading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Loading extension GLX (II) LoadModule: "record" (II) Loading /usr/X11R6/lib/modules/extensions/librecord.a (II) Module record: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.13.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.1 (II) Loading extension RECORD (II) LoadModule: "freetype" (II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a (II) Module freetype: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.1.10 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.3 (II) Loading font FreeType (II) LoadModule: "type1" (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a (II) Module type1: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.1 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.3 (II) Loading font Type1 (II) Loading font CID (II) LoadModule: "s3virge" (II) Loading /usr/X11R6/lib/modules/drivers/s3virge_drv.o (II) Module s3virge: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.8.3 Module class: XFree86 Video Driver ABI class: XFree86 Video Driver, version 0.5 (II) LoadModule: "mouse" (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o (II) Module mouse: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 Module class: XFree86 XInput Driver ABI class: XFree86 XInput driver, version 0.3 (II) S3VIRGE: driver (version 1.8.3) for S3 ViRGE chipsets: virge, 86C325, virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2, 86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365, trio 3d/2x, 86C362, 86C368 (II) Primary Device is: PCI 01:01:0 (--) Assigning device section with no busID to primary device (--) Chipset trio 3d found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0xf3eff000 - 0xf3efffff (0x1000) MX[B] [6] -1 0xf3f00000 - 0xf3ffffff (0x100000) MX[B] [7] -1 0xf3dff000 - 0xf3dfffff (0x1000) MX[B] [8] -1 0xec000000 - 0xefffffff (0x4000000) MX[B] [9] -1 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [10] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B](B) [11] -1 0x0000ffff - 0x0000ffff (0x1) IX[B] [12] -1 0x00000000 - 0x000000ff (0x100) IX[B] [13] -1 0x00007800 - 0x000078ff (0x100) IX[B] [14] -1 0x00007c60 - 0x00007c7f (0x20) IX[B] [15] -1 0x0000ff00 - 0x0000ff1f (0x20) IX[B] [16] -1 0x0000fff0 - 0x0000ffff (0x10) IX[B] (II) resource ranges after probing: [0] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0xf3eff000 - 0xf3efffff (0x1000) MX[B] [6] -1 0xf3f00000 - 0xf3ffffff (0x100000) MX[B] [7] -1 0xf3dff000 - 0xf3dfffff (0x1000) MX[B] [8] -1 0xec000000 - 0xefffffff (0x4000000) MX[B] [9] -1 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [10] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B](B) [11] 0 0x000a0000 - 0x000affff (0x10000) MS[B] [12] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [13] 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [14] -1 0x0000ffff - 0x0000ffff (0x1) IX[B] [15] -1 0x00000000 - 0x000000ff (0x100) IX[B] [16] -1 0x00007800 - 0x000078ff (0x100) IX[B] [17] -1 0x00007c60 - 0x00007c7f (0x20) IX[B] [18] -1 0x0000ff00 - 0x0000ff1f (0x20) IX[B] [19] -1 0x0000fff0 - 0x0000ffff (0x10) IX[B] [20] 0 0x000003b0 - 0x000003bb (0xc) IS[B] [21] 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/X11R6/lib/modules/libvgahw.a (II) Module vgahw: vendor="The XFree86 Project" compiled for 4.2.0, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.5 (**) S3VIRGE(0): Depth 16, (--) framebuffer bpp 16 (==) S3VIRGE(0): RGB weight 565 (==) S3VIRGE(0): Default visual is TrueColor (==) S3VIRGE(0): Using HW Cursor (==) S3VIRGE(0): Using fb. (==) S3VIRGE(0): mx_cr3a_fix. (==) S3VIRGE(0): XVideo allowed (depends on chipset). (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/X11R6/lib/modules/libvbe.a (II) Module vbe: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.5 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Loading /usr/X11R6/lib/modules/linux/libint10.a (II) Module int10: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.5 (II) S3VIRGE(0): initializing int10 (II) S3VIRGE(0): Primary V_BIOS segment is: 0xc000 (II) S3VIRGE(0): VESA BIOS detected (II) S3VIRGE(0): VESA VBE Version 2.0 (II) S3VIRGE(0): VESA VBE Total Mem: 4096 kB (II) S3VIRGE(0): VESA VBE OEM: S3 Incorporated Trio3D. (II) S3VIRGE(0): VESA VBE OEM Software Rev: 1.1 (II) S3VIRGE(0): VESA VBE OEM Vendor: S3 Incorporated. (II) S3VIRGE(0): VESA VBE OEM Product: Trio3D (II) S3VIRGE(0): VESA VBE OEM Product Rev: Rev B (--) S3VIRGE(0): Chipset: "trio 3d" (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11R6/lib/modules/libddc.a (II) Module ddc: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.5 (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Reloading /usr/X11R6/lib/modules/libddc.a (II) S3VIRGE(0): VESA VBE DDC supported (II) S3VIRGE(0): VESA VBE DDC Level 2 (II) S3VIRGE(0): VESA VBE DDC transfer in appr. 1 sec. (II) S3VIRGE(0): VESA VBE DDC read successfully (II) S3VIRGE(0): Manufacturer: DPC Model: 770 Serial#: 0 (II) S3VIRGE(0): Year: 1997 Week: 49 (II) S3VIRGE(0): EDID Version: 1.0 (II) S3VIRGE(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V (II) S3VIRGE(0): Sync: Separate Composite (II) S3VIRGE(0): Max H-Image Size [cm]: horiz.: 32 vert.: 24 (II) S3VIRGE(0): Gamma: 2.67 (II) S3VIRGE(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display (II) S3VIRGE(0): redX: 0.620 redY: 0.345 greenX: 0.290 greenY: 0.610 (II) S3VIRGE(0): blueX: 0.155 blueY: 0.065 whiteX: 0.281 whiteY: 0.311 (II) S3VIRGE(0): Supported VESA Video Modes: (II) S3VIRGE(0): 720x400@70Hz (II) S3VIRGE(0): 720x400@88Hz (II) S3VIRGE(0): 640x480@60Hz (II) S3VIRGE(0): 640x480@67Hz (II) S3VIRGE(0): 640x480@72Hz (II) S3VIRGE(0): 640x480@75Hz (II) S3VIRGE(0): 800x600@56Hz (II) S3VIRGE(0): 800x600@60Hz (II) S3VIRGE(0): 800x600@72Hz (II) S3VIRGE(0): 800x600@75Hz (II) S3VIRGE(0): 832x624@75Hz (II) S3VIRGE(0): 1024x768@87Hz (interlaced) (II) S3VIRGE(0): 1024x768@60Hz (II) S3VIRGE(0): 1024x768@70Hz (II) S3VIRGE(0): 1024x768@75Hz (II) S3VIRGE(0): 1152x870@75Hz (II) S3VIRGE(0): Manufacturer's mask: 0 (II) S3VIRGE(0): Supported Future Video Modes: (II) S3VIRGE(0): #0: hsize: 800 vsize 600 refresh: 85 vid: 22853 (II) S3VIRGE(0): #1: hsize: 1024 vsize 768 refresh: 85 vid: 22881 (II) S3VIRGE(0): #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337 (II) S3VIRGE(0): #3: hsize: 640 vsize 480 refresh: 85 vid: 22833 (II) S3VIRGE(0): #4: hsize: 1280 vsize 960 refresh: 60 vid: 16513 (II) S3VIRGE(0): Supported additional Video Mode: (II) S3VIRGE(0): clock: 108.0 MHz Image Size: 281 x 225 mm (II) S3VIRGE(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0 (II) S3VIRGE(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0 (II) S3VIRGE(0): Supported additional Video Mode: (II) S3VIRGE(0): clock: 35.5 MHz Image Size: 300 x 225 mm (II) S3VIRGE(0): h_active: 720 h_sync: 756 h_sync_end 828 h_blank_end 936 h_border: 0 (II) S3VIRGE(0): v_active: 400 v_sync: 401 v_sync_end 404 v_blanking: 446 v_border: 0 (II) S3VIRGE(0): Supported additional Video Mode: (II) S3VIRGE(0): clock: 31.5 MHz Image Size: 300 x 225 mm (II) S3VIRGE(0): h_active: 640 h_sync: 672 h_sync_end 736 h_blank_end 832 h_border: 0 (II) S3VIRGE(0): v_active: 400 v_sync: 401 v_sync_end 404 v_blanking: 445 v_border: 0 (II) S3VIRGE(0): Supported additional Video Mode: (II) S3VIRGE(0): clock: 31.5 MHz Image Size: 300 x 225 mm (II) S3VIRGE(0): h_active: 640 h_sync: 672 h_sync_end 736 h_blank_end 832 h_border: 0 (II) S3VIRGE(0): v_active: 350 v_sync: 382 v_sync_end 385 v_blanking: 445 v_border: 0 (==) S3VIRGE(0): Using gamma correction (1.0, 1.0, 1.0) (--) S3VIRGE(0): videoram: 4096k (--) S3VIRGE(0): Detected current MCLK value of 100.227 MHz (II) S3VIRGE(0): Monitor0: Using hsync range of 31.50-48.50 kHz (II) S3VIRGE(0): Monitor0: Using vrefresh range of 50.00-70.00 Hz (II) S3VIRGE(0): Clock range: 20.00 to 270.00 MHz (II) S3VIRGE(0): Not using mode "1400x1050" (hsync out of range) (II) S3VIRGE(0): Not using mode "1400x1050" (hsync out of range) (II) S3VIRGE(0): Not using mode "1400x1050" (hsync out of range) (II) S3VIRGE(0): Not using mode "1400x1050" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x350" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "640x400" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "720x400" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "640x480" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "640x480" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "640x480" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "800x600" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "800x600" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1024x768" (vrefresh out of range) (II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1152x864" (hsync out of range) (II) S3VIRGE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1280x960" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1280x960" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range) (II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range) (II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range) (II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range) (II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range) (II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "832x624" (hsync out of range) (II) S3VIRGE(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1152x864" (hsync out of range) (II) S3VIRGE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1600x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan) (II) S3VIRGE(0): Not using default mode "1920x1200" (insufficient memory for mode) (II) S3VIRGE(0): Not using default mode "960x600" (bad mode clock/interlace/doublescan) (--) S3VIRGE(0): Virtual size is 1024x768 (pitch 1024) (**) S3VIRGE(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz (II) S3VIRGE(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (**) S3VIRGE(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (II) S3VIRGE(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (**) S3VIRGE(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (II) S3VIRGE(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (--) S3VIRGE(0): Display dimensions: (320, 240) mm (--) S3VIRGE(0): DPI set to (81, 81) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/X11R6/lib/modules/libfb.a (II) Module fb: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 ANSI C Emulation, version 0.1 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/X11R6/lib/modules/libxaa.a (II) Module xaa: vendor="The XFree86 Project" compiled for 4.2.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.5 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/X11R6/lib/modules/libramdac.a (II) Module ramdac: vendor="The XFree86 Project" compiled for 4.2.0, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.5 (II) do I need RAC? No, I don't. (II) resource ranges after preInit: [0] 0 0xf4000000 - 0xf7ffffff (0x4000000) MS[B] [1] -1 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [2] -1 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [3] -1 0x000f0000 - 0x000fffff (0x10000) MX[B] [4] -1 0x000c0000 - 0x000cffff (0x10000) MX[B] [5] -1 0x00000000 - 0x0009ffff (0xa0000) MX[B] [6] -1 0xf3eff000 - 0xf3efffff (0x1000) MX[B] [7] -1 0xf3f00000 - 0xf3ffffff (0x100000) MX[B] [8] -1 0xf3dff000 - 0xf3dfffff (0x1000) MX[B] [9] -1 0xec000000 - 0xefffffff (0x4000000) MX[B] [10] -1 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [11] -1 0xf4000000 - 0xf7ffffff (0x4000000) MX[B](B) [12] 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD) [13] 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD) [14] 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD) [15] -1 0x0000ffff - 0x0000ffff (0x1) IX[B] [16] -1 0x00000000 - 0x000000ff (0x100) IX[B] [17] -1 0x00007800 - 0x000078ff (0x100) IX[B] [18] -1 0x00007c60 - 0x00007c7f (0x20) IX[B] [19] -1 0x0000ff00 - 0x0000ff1f (0x20) IX[B] [20] -1 0x0000fff0 - 0x0000ffff (0x10) IX[B] [21] 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU) [22] 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU) (==) S3VIRGE(0): Write-combining range (0xf4000000,0x400000) (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 Trio3D -- Display is on...turning off Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f905f80 Trio3D -- GE was on ST#1: 0x20007f80 ST#2: 0x20007f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x20015f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f807f80 (**) S3VIRGE(0): Using FB (II) S3VIRGE(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits 8x8 mono pattern filled rectangles CPU to Screen color expansion Image Writes Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) S3VIRGE(0): Backing store disabled (==) S3VIRGE(0): Silken mouse enabled (**) Option "dpms" (**) S3VIRGE(0): DPMS enabled (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension LBX (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (**) Option "Protocol" "PS/2" (**) Mouse0: Protocol: "PS/2" (**) Option "CorePointer" (**) Mouse0: Core Pointer (**) Option "Device" "/dev/psaux" (**) Option "Emulate3Buttons" "no" (**) Option "ZAxisMapping" "4 5" (**) Mouse0: ZAxisMapping: buttons 4 and 5 (**) Mouse0: Buttons: 5 (II) Keyboard "Keyboard0" handled by legacy driver (II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE) AUDIT: Sun Jul 3 16:21:16 2005: 6492 X: client 29 rejected from local host AUDIT: Sun Jul 3 16:21:23 2005: 6492 X: client 29 rejected from local host AUDIT: Sun Jul 3 16:21:49 2005: 6492 X: client 29 rejected from local host AUDIT: Sun Jul 3 16:22:28 2005: 6492 X: client 29 rejected from local host AUDIT: Sun Jul 3 16:22:45 2005: 6492 X: client 29 rejected from IP 127.0.0.1 port 33690 AUDIT: Sun Jul 3 16:22:57 2005: 6492 X: client 30 rejected from IP 127.0.0.1 port 33693 Trio3D -- Display is on...turning off Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f905f80 Trio3D -- GE was on ST#1: 0x20007f80 ST#2: 0x20007f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x35807f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x35915f80 S3VGEReset called from s3v_accel.c line 410 Trio3D -- GE was on ST#1: 0x35915f80 ST#2: 0x35915f80 restarting S3 graphics engine reset 1 ...35115f80 Trio3D -- GE was on ST#1: 0x35115f80 ST#2: 0x35115f80 restarting S3 graphics engine reset 2 ...34915f80 Trio3D -- GE was on ST#1: 0x34915f80 ST#2: 0x34915f80 restarting S3 graphics engine reset 3 ...34115f80 Trio3D -- GE was on ST#1: 0x34115f80 ST#2: 0x34115f80 restarting S3 graphics engine reset 4 ...33915f80 Trio3D -- GE was on ST#1: 0x33915f80 ST#2: 0x33915f80 restarting S3 graphics engine reset 5 ...33115f80 Trio3D -- GE was on ST#1: 0x33115f80 ST#2: 0x33115f80 restarting S3 graphics engine reset 6 ...32915f80 Trio3D -- GE was on ST#1: 0x32915f80 ST#2: 0x32915f80 restarting S3 graphics engine reset 7 ...32115f80 Trio3D -- GE was on ST#1: 0x32115f80 ST#2: 0x32115f80 restarting S3 graphics engine reset 8 ...31915f80 Trio3D -- GE was on ST#1: 0x31915f80 ST#2: 0x31915f80 restarting S3 graphics engine reset 9 ...31115f80 restarting S3 graphics engine reset 1 ...2d915f80 Trio3D -- GE was on ST#1: 0x2d915f80 ST#2: 0x2d915f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x2d007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x2c815f80 S3VGEReset called from s3v_accel.c line 410 Trio3D -- GE was on ST#1: 0x2d115f80 ST#2: 0x2d115f80 restarting S3 graphics engine reset 1 ...2c915f80 Trio3D -- GE was on ST#1: 0x2c915f80 ST#2: 0x2c915f80 restarting S3 graphics engine reset 2 ...2c115f80 Trio3D -- GE was on ST#1: 0x2c115f80 ST#2: 0x2c115f80 restarting S3 graphics engine reset 3 ...2b915f80 Trio3D -- GE was on ST#1: 0x2b915f80 ST#2: 0x2b915f80 restarting S3 graphics engine reset 4 ...2b115f80 Trio3D -- GE was on ST#1: 0x2b115f80 ST#2: 0x2b115f80 restarting S3 graphics engine reset 5 ...2a915f80 Trio3D -- GE was on ST#1: 0x2a915f80 ST#2: 0x2a915f80 restarting S3 graphics engine reset 6 ...2a115f80 Trio3D -- GE was on ST#1: 0x2a115f80 ST#2: 0x2a115f80 restarting S3 graphics engine reset 7 ...29915f80 Trio3D -- GE was on ST#1: 0x29915f80 ST#2: 0x29915f80 restarting S3 graphics engine reset 8 ...29115f80 Trio3D -- GE was on ST#1: 0x29115f80 ST#2: 0x29115f80 restarting S3 graphics engine reset 9 ...28915f80 restarting S3 graphics engine reset 2 ...25115f80 Trio3D -- GE was on ST#1: 0x25115f80 ST#2: 0x25115f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x24807f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x24915f80 S3VGEReset called from s3v_accel.c line 410 Trio3D -- GE was on ST#1: 0x24915f80 ST#2: 0x24915f80 restarting S3 graphics engine reset 1 ...24115f80 Trio3D -- GE was on ST#1: 0x24115f80 ST#2: 0x24115f80 restarting S3 graphics engine reset 2 ...23915f80 Trio3D -- GE was on ST#1: 0x23915f80 ST#2: 0x23915f80 restarting S3 graphics engine reset 3 ...23115f80 Trio3D -- GE was on ST#1: 0x23115f80 ST#2: 0x23115f80 restarting S3 graphics engine reset 4 ...22915f80 Trio3D -- GE was on ST#1: 0x22915f80 ST#2: 0x22915f80 restarting S3 graphics engine reset 5 ...22115f80 Trio3D -- GE was on ST#1: 0x22115f80 ST#2: 0x22115f80 restarting S3 graphics engine reset 6 ...21915f80 Trio3D -- GE was on ST#1: 0x21915f80 ST#2: 0x21915f80 restarting S3 graphics engine reset 7 ...21115f80 Trio3D -- GE was on ST#1: 0x21115f80 ST#2: 0x21115f80 restarting S3 graphics engine reset 8 ...20915f80 Trio3D -- GE was on ST#1: 0x20915f80 ST#2: 0x20915f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f815f80 (II) Open APM successful Trio3D -- Display is on...turning off Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f807f80 Trio3D -- GE was on ST#1: 0x20007f80 ST#2: 0x20007f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x20105f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x20015f80 (II) Got reinsert event: reinitializing PS/2 mouse (II) Got reinsert event: reinitializing PS/2 mouse Fatal server error: Caught signal 11. Server aborting When reporting a problem related to a server crash, please send the full server output, not just the last messages. This can be found in the log file "/var/log/XFree86.0.log". Please report problems to xfree86@xxxxxxxxxxxx Trio3D -- Display is on...turning off Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f807f80 Trio3D -- GE was on ST#1: 0x20007f80 ST#2: 0x20007f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20807f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x21915f80 Trio3D -- S3VNopAllCmdSets: SubsysStats#1 = 0x20007f80 Trio3D -- S3VNopAllCmdSets: state changed after 0 iterations Trio3D -- S3VNopAllCmdSets: SubsysStats#2 = 0x1f807f80
