I also noticed that you are loading the module LoadModule: "fbdev". Therefore you should (also) manually set your BusID in the Device section of your X config file. Do you have a section Option "UseFBDev" in your config? I am not sure what will happen in your specific case if you run x without FBDev, but you could also give that a try. If you don't have that option specified in your x config It will default as off. -M ________________________________________ From: ASIF IQBAL [mailto:ashuasif02@xxxxxxxxxxxxxx] Sent: Saturday, December 04, 2004 7:43 AM To: xfree86@xxxxxxxxxxx Cc: Michael Hamilton Subject: Re: [XFree86 on Solaris/X86] (EE) GLINT(1): Cannot read V_BIOS(3) Hello! Michael Ihave attatched the log file. Please have a look on it. and give me the solution for the error "(EE) GLINT(1): Cannot read V_BIOS (3)". as reflected in the log file. thanking you. On Sat, 04 Dec 2004 Michael Hamilton wrote : >Have you tried setting your VideoRam manually in the xconfig file under the device section? >Also try manually setting the ChipSet name. Can you attach your XFree86.0.log? > >-M > >________________________________________ > From: ASIF IQBAL [mailto:ashuasif02@xxxxxxxxxxxxxx] >Sent: Friday, December 03, 2004 5:53 AM >To: xfree86@xxxxxxxxxxx >Cc: Marc Aurele La France; xfree86@xxxxxxxxxxx >Subject: Re: Re: [XFree86 on Solaris/X86] (EE) GLINT(1): Cannot read V_BIOS(3) > > > > >Hi! Marc > >I have installed the aperture driver from ..xc/programs/Xserver/hw/xfree86/etc/apSolaris.shar file >and when i again try to configure using the command "XFree86 -configure", the log file "XFree86.0.log" >still reflects the same error. ie "(EE) GLINT(1): Cannot read V_BIOS (3)". >I also tried to find in the CVS of XFree86 and unable to find. Can you please tell me the exact >location where it is addressed, and if possible give me the detailed solution for this problem. > >thanking you, > > > >On Tue, 30 Nov 2004 Marc Aurele La France wrote : > >On Tue, 30 Nov 2004, asif iqbal wrote: > > > >>I am trying to bring up my Permedia card on PCI by XFree86-4.4.0 on Solaris-8/X86. At first I have configured XFree86 only with "SIS" card, and it worked fine. Then while I tried to configure both SIS and Permedia cards together by the command "XFree86 -configure", the file in /var/log/XFree86.0.log have the error message showing like "(EE) GLINT(1): Cannot read V_BIOS(3)" can anybody give me the solution for this. And for the configured file i got after the above step "XF86Config.new", and i tried to check the Xserver by the command "XFree86 -xf86config XF86Config.new" the system hanged. Please give me the solution for this. > > > >There is a possible fix for this in our CVS. If that doesn't work, it might be that the driver for /dev/xsvc doesn't allow certain mappings, in which case you would have to switch to the XFree86-provided aperture driver. > > > >Marc. > > > >+----------------------------------+-----------------------------------+ > >| Marc Aurele La France | work: 1-780-492-9310 | > >| Computing and Network Services | fax: ; 1-780-492-1729 | > >| 352 General Services Building | email: tsi@xxxxxxxxxxx | > >| University of Alberta +-----------------------------------+ > >| Edmonton, Alberta | | > >| T6G 2H1 | Standard disclaimers apply | > >| CANADA | | > >+----------------------------------+-----------------------------------+ > >XFree86 developer and VP. ATI driver and X server internals. > >_______________________________________________ > >XFree86 mailing list > >XFree86@xxxxxxxxxxx > >http://XFree86.Org/mailman/listinfo/xfree86 > > > > > >_______________________________________________ >XFree86 mailing list >XFree86@xxxxxxxxxxx >http://XFree86.Org/mailman/listinfo/xfree86 _______________________________________________ XFree86 mailing list XFree86@xxxxxxxxxxx http://XFree86.Org/mailman/listinfo/xfree86
