s3virge/mx running xfree86-4.3.0.1 won't switch back to console

[Joern Merkel <joernm@xxxxxxxxxxxxxxxxxxxxx>]

Hi,

I've got an Toshiba 460CDT with a s3virge/mx running xfree86-4.3.0.1.
The Problem is, when terminating X my display looks kinda messed. That's
what a CRT would do if you've got completely wrong timings, I guess.
When I use the "vesa"-driver instead of "s3virge" it switches back, but
my console is kinda messed up, it has too much lines.
And when I boot with a framebuffer-console (mode 0x413) X won't even
start (s3virge-driver). The display just stays black.
I thought of timing problems and fiddled a bit with my modelines, but it
 had no effect.

Thats what /proc/pci says:

<snip>
  Bus  1, device   3, function  0:
    VGA compatible controller: S3 Inc. ViRGE/MX (rev 6).
      IRQ 11.
      Master Capable.  No bursts.  Min Gnt=4.Max Lat=255.
      Non-prefetchable 32 bit memory at 0xf8000000 [0xfbffffff].
<snip>

and thats my XF86Config so far:

Section "ServerLayout"
	Identifier     "XFree86 Configured"
	Screen      0  "Screen0" 0 0
	InputDevice    "Mouse0" "CorePointer"
	InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
	RgbPath      "/usr/X11R6/lib/X11/rgb"
	ModulePath   "/usr/X11R6/lib/modules"
	FontPath     "/usr/X11R6/lib/X11/fonts/misc/"
	FontPath     "/usr/X11R6/lib/X11/fonts/Speedo/"
	FontPath     "/usr/X11R6/lib/X11/fonts/Type1/"
	FontPath     "/usr/X11R6/lib/X11/fonts/CID/"
	FontPath     "/usr/X11R6/lib/X11/fonts/75dpi/"
	FontPath     "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection

Section "Module"
	Load  "extmod"
	Load  "glx"
	Load  "dri"
	Load  "dbe"
	Load  "record"
	Load  "xtrap"
	Load  "speedo"
	Load  "type1"
EndSection

Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "keyboard"
EndSection

Section "InputDevice"
	Identifier  "Mouse0"
	Driver      "mouse"
	Option	    "Protocol" "PS/2"
	Option      "Emulate3Buttons"
	Option	    "Device" "/dev/mouse"
EndSection

Section "Monitor"
	Identifier   "Monitor0"
	VendorName   "TOS"
	ModelName    "5081"
	HorizSync	30 - 79
	VertRefresh	40 - 60
EndSection

Section "Device"
	Identifier  "Card0"
	Driver      "s3virge"
	VendorName  "S3 Inc."
	BoardName   "ViRGE/MX"
	BusID       "PCI:1:3:0"
EndSection

Section "Screen"
	Identifier "Screen0"
	Device     "Card0"
	Monitor    "Monitor0"
	DefaultDepth 16
	SubSection "Display"
		Depth     1
	EndSubSection
	SubSection "Display"
		Depth     4
	EndSubSection
	SubSection "Display"
		Depth     8
	EndSubSection
	SubSection "Display"
		Depth     15
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes	"800x600" "640x480" "400x300"
	EndSubSection
	SubSection "Display"
		Depth     24
	EndSubSection
EndSection


anybody got a clue ?

regards

JM


_______________________________________________
XFree86 mailing list
XFree86@xxxxxxxxxxx
http://XFree86.Org/mailman/listinfo/xfree86