Setting up multi monitors with two graphics cards.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello! I'm trying to get multi monitor support
working, I am having some problems. I'm running
Slackware 9.1 on a Sony Viao. I have two graphics
cards, a ATI radeon 7500, and a intergraded intel 64M
graphics card, and two 17 IBM Monitors.  My output of
'lspci -v' is below, forllowd by my 'XF86Config', then
the XFree86 log:


----------------------------------------------
lspci -vv
----------------------------------------------
00:00.0 Host bridge: Intel Corp.: Unknown device 2570
(rev 02)
        Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at f8000000 (32-bit,
prefetchable) [size=64M]
        Capabilities: [e4] #09 [0106]
        Capabilities: [a0] AGP version 3.0
                Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+
ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+
GART64- 64bit- FW- Rate=x1

00:01.0 PCI bridge: Intel Corp.: Unknown device 2571
(rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Bus: primary=00, secondary=01, subordinate=01,
sec-latency=64
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: fe900000-fe9fffff
        Prefetchable memory behind bridge:
e7f00000-f7efffff
        BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort-
>Reset- FastB2B-

00:1d.0 USB Controller: Intel Corp.: Unknown device
24d2 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Sony Corporation: Unknown device
8159
        Control: I/O+ Mem- BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at e400 [size=32]

00:1d.1 USB Controller: Intel Corp.: Unknown device
24d4 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Sony Corporation: Unknown device
8159
        Control: I/O+ Mem- BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 4: I/O ports at e800 [size=32]

00:1d.2 USB Controller: Intel Corp.: Unknown device
24d7 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Sony Corporation: Unknown device
8159
        Control: I/O+ Mem- BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at ec00 [size=32]

00:1d.7 USB Controller: Intel Corp.: Unknown device
24dd (rev 02) (prog-if 20 [EHCI])
        Subsystem: Sony Corporation: Unknown device
8159
        Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 23
        Region 0: Memory at febffc00 (32-bit,
non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2-
AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0
PME-
        Capabilities: [58] #0a [20a0]

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI
Bridge (rev c2) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=02,
sec-latency=64
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: fea00000-feafffff
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort-
>Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp.: Unknown device 24d0
(rev 02)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface: Intel Corp.: Unknown device
24db (rev 02) (prog-if 8a [Master SecP PriP])
        Subsystem: Sony Corporation: Unknown device
8159
        Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at <unassigned>
        Region 1: I/O ports at <unassigned>
        Region 2: I/O ports at <unassigned>
        Region 3: I/O ports at <unassigned>
        Region 4: I/O ports at fc00 [size=16]
        Region 5: Memory at 20000000 (32-bit,
non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corp.: Unknown device 24d3 (rev
02)
        Subsystem: Sony Corporation: Unknown device
8159
        Control: I/O+ Mem- BusMaster- SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 17
        Region 4: I/O ports at 0400 [size=32]

00:1f.5 Multimedia audio controller: Intel Corp.:
Unknown device 24d5 (rev 02)
        Subsystem: Sony Corporation: Unknown device
815b
        Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 0: I/O ports at d800 [size=256]
        Region 1: I/O ports at d400 [size=64]
        Region 2: Memory at febff800 (32-bit,
non-prefetchable) [size=512]
        Region 3: Memory at febff400 (32-bit,
non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2-
AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0
PME-

00:1f.6 Modem: Intel Corp.: Unknown device 24d6 (rev
02) (prog-if 00 [Generic])
        Subsystem: Sony Corporation: Unknown device
8128
        Control: I/O+ Mem- BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 0: I/O ports at e000 [size=256]
        Region 1: I/O ports at dc00 [size=128]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2-
AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0
PME-

01:00.0 VGA compatible controller: ATI Technologies
Inc Radeon RV200 QW [Radeon 7500] (prog-if 00 [VGA])
        Subsystem: ATI Technologies Inc Radeon 7500
        Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2000ns min), cache line size 04
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at e8000000 (32-bit,
prefetchable) [size=128M]
        Region 1: I/O ports at a800 [size=256]
        Region 2: Memory at fe9f0000 (32-bit,
non-prefetchable) [size=64K]
        Expansion ROM at fe9c0000 [disabled]
[size=128K]
        Capabilities: [58] AGP version 2.0
                Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+
ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
                Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+
GART64- 64bit- FW- Rate=x1
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0
PME-

02:08.0 Ethernet controller: Intel Corp.: Unknown
device 1050 (rev 02)
        Subsystem: Sony Corporation: Unknown device
815c
        Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2000ns min, 14000ns max)
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at feaff000 (32-bit,
non-prefetchable) [size=4K]
        Region 1: I/O ports at bc00 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+
AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2
PME-

02:0e.0 FireWire (IEEE 1394): NEC Corporation: Unknown
device 00f2 (rev 01) (prog-if 10 [OHCI])
        Subsystem: Sony Corporation: Unknown device
811e
        Control: I/O- Mem+ BusMaster+ SpecCycle-
MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (5000ns min, 11000ns max), cache
line size 04
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at feafe000 (32-bit,
non-prefetchable) [size=4K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+
AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0
PME-
---------------------------------------------
XF86Config
---------------------------------------------
Section "ServerLayout"
 Identifier     "layout1"
        Screen         "Screen 1" RightOf "Screen2"
        Screen        "Screen2" 
        InputDevice    "Mouse1" "CorePointer"
        InputDevice    "Keyboard1" "CoreKeyboard"
        Option    "Xinerama" "on"
EndSection
Section "Files" 
RgbPath      "/usr/X11R6/lib/X11/rgb"
        FontPath     "/usr/X11R6/lib/X11/fonts/local/"
        FontPath     "/usr/X11R6/lib/X11/fonts/misc/"
        FontPath    
"/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
        FontPath    
"/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
        FontPath     "/usr/X11R6/lib/X11/fonts/Type1/"
        FontPath     "/usr/X11R6/lib/X11/fonts/CID/"
        FontPath    
"/usr/X11R6/lib/X11/fonts/Speedo/"
        FontPath     "/usr/X11R6/lib/X11/fonts/75dpi/"
        FontPath    
"/usr/X11R6/lib/X11/fonts/100dpi/"
        FontPath    
"/usr/X11R6/lib/X11/fonts/cyrillic/"
EndSection
Section "Module"
 Load  "dbe"     # Double buffer extension
        SubSection "extmod"
                Option      "omit xfree86-dga"   #
don't initialise the DGA extension
        EndSubSection
        Load  "type1"
        Load  "freetype"
        Load  "speedo"
# This loads the GLX module
        Load  "glx"
        Load  "dr
EndSection
Section "InputDevice"
   Identifier  "Keyboard1"
        Driver      "Keyboard"
EndSection
 Identifier  "Mouse1"
        Driver      "mouse"
        Option      "Protocol" "IMPS/2"
# The mouse device.  The device is normally set to
/dev/mouse,
        Option      "Device" "/dev/psaux"
#   Option "Device"      "/dev/ttyS0"
        Option      "Buttons" "5"
        Option      "ZAxisMapping" "4 5"
# When using XQUEUE, comment out the above two lines,
and uncomment
EndSection
Section "Monitor" 
        Identifier   "My Monitor"
        HorizSync    31.5 - 50.0
        VertRefresh  40.0 - 90.0
EndSection
Section "Monitor"
        Identifier   "Monitor1"
        HorizSync    31.5 - 50.0
        VertRefresh  40.0 - 90.0
EndSection
Section "Device"
        Identifier  "VESA Framebuffer"
        Driver      "vesa"
EndSection
Section "Device"
        Identifier  "Card1"
        Driver      "vesa"
        ChipSet     "vesa"
        Card        "vesa"
        ChipId      0x0
        ChipRev     0x0
        BusID       "PCI:0:00:0"
        IRQ         0
EndSection
Section "Screen"
        Identifier "Screen 1" 
        Device     "VESA Framebuffer"
        Monitor    "My Monitor"
        DefaultDepth     16
        SubSection "Display"
                Virtual   1024 768
                        Modes    "1024x768" "800x600"
"640x480"
        EndSubSection
        SubSection "Display"
                Depth     16
                Modes    "1024x768" "800x600"
"640x480"
        EndSubSection
        SubSection "Display"
                Depth     24
                Modes    "1024x768" "800x600"
"640x480"
        EndSubSection
        SubSection "Display"
                Depth     32
                Modes    "1024x768" "800x600"
"640x480"
        EndSubSection
EndSection
Section "Screen"
        Identifier "Screen2"
        Device     "Card1"
        Monitor    "Monitor1"
        DefaultDepth 16
EndSection
_____________________________________________
XFree86.0.log  
---------------------------------------------
(This was large, I attached it)

***END***

If anyone can see what I'm doing wrong here I would
appreaciate it.

Thank you.

Stratis. 

Attachment: XFree86.0.log
Description: XFree86.0.log


[Index of Archives]     [X Forum]     [Xorg]     [XFree86 Newbie]     [IETF Announce]     [Security]     [Font Config]     [Bugtraq]     [Yosemite]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux Kernel]

  Powered by Linux