Hello, I have a little problem : I'm currently using XFree4.3.0 and running slackware 9.1 I have a Voodoo 3 2000 Video card. So I'm using the tdfx driver... When I run xinit (or startx), i get the following message : ----------------------------------------------- TDFX(0) Unknown reason for exception TDFX(0) Cannot continue ------------------------------------------------ Then I get only 60 FPS with glxgears, although I used to get 1000 or so before... And glxinfo says Direct Rendering: Yes Below you can find my XFree86 log : i noticed a problem with a VESA BIOS but I don't know if it is the problem. The kernel-module tdfx is shown with lsmod. Excuse me for my bad english, And thanks a lot for your tips Marc. PS: After the XFree86 log is my XF86Config file. --------------------------------------------------------------------------------- XFree86 Version 4.3.0 Release Date: 27 February 2003 X Protocol Version 11, Revision 0, Release 6.6 Build Operating System: Linux 2.4.22 i686 [ELF] Build Date: 16 September 2003 Before reporting problems, check http://www.XFree86.Org/ to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/XFree86.0.log", Time: Sat Dec 20 09:51:51 2003 (==) Using config file: "/etc/X11/XF86Config" (==) ServerLayout "Simple Layout" (**) |-->Screen "Screen 1" (0) (**) | |-->Monitor "Flatron 795FT (LG)" (**) | |-->Device "Voodoo3 (generic)" (**) |-->Input Device "Mouse1" (**) |-->Input Device "Keyboard1" (**) Option "AutoRepeat" "500 30" (**) Option "XkbRules" "xfree86" (**) XKB: rules: "xfree86" (**) Option "XkbModel" "pc102" (**) XKB: model: "pc102" (**) Option "XkbLayout" "fr" (**) XKB: layout: "fr" (==) Keyboard: CustomKeycode disabled (WW) `fonts.dir' not found (or not valid) in "/usr/X11R6/lib/X11/fonts/100dpi/". Entry deleted from font path. (Run 'mkfontdir' on "/usr/X11R6/lib/X11/fonts/100dpi/"). (WW) `fonts.dir' not found (or not valid) in "/usr/X11R6/lib/X11/fonts/Speedo/". Entry deleted from font path. (Run 'mkfontdir' on "/usr/X11R6/lib/X11/fonts/Speedo/"). (WW) `fonts.dir' not found (or not valid) in "/usr/X11R6/lib/X11/fonts/Type1/". Entry deleted from font path. (Run 'mkfontdir' on "/usr/X11R6/lib/X11/fonts/Type1/"). (**) FontPath set to "/usr/X11R6/lib/X11/fonts/local/,/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/75dpi/" (**) RgbPath set to "/usr/X11R6/lib/X11/rgb" (==) ModulePath set to "/usr/X11R6/lib/modules" (--) using VT number 7 (WW) Open APM failed (/dev/apm_bios) (No such device) (II) Module ABI versions: XFree86 ANSI C Emulation: 0.2 XFree86 Video Driver: 0.6 XFree86 XInput driver : 0.4 XFree86 Server Extension : 0.2 XFree86 Font Renderer : 0.4 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Module bitmap: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11R6/lib/modules/libpcidata.a (II) Module pcidata: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.6 (II) PCI: Probing config type using method 1 (II) PCI: Config type is 1 (II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 8086,7190 card 0000,0000 rev 03 class 06,00,00 hdr 00 (II) PCI: 00:01:0: chip 8086,7191 card 0000,0000 rev 03 class 06,04,00 hdr 01 (II) PCI: 00:07:0: chip 8086,7110 card 0000,0000 rev 02 class 06,01,00 hdr 80 (II) PCI: 00:07:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00 (II) PCI: 00:07:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00 (II) PCI: 00:07:3: chip 8086,7113 card 0000,0000 rev 02 class 06,80,00 hdr 00 (II) PCI: 00:10:0: chip 127a,2013 card 1436,2113 rev 01 class 07,80,00 hdr 00 (II) PCI: 00:12:0: chip 10ec,8139 card 1799,5000 rev 10 class 02,00,00 hdr 00 (II) PCI: 00:14:0: chip 1274,1371 card 1274,1371 rev 08 class 04,01,00 hdr 00 (II) PCI: 01:00:0: chip 121a,0005 card 121a,0034 rev 01 class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) PCI-to-PCI bridge: (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0088 (VGA_EN is set) (II) Bus 1 I/O range: [0] -1 0 0x0000a000 - 0x0000afff (0x1000) IX[B] (II) Bus 1 non-prefetchable memory range: [0] -1 0 0xebe00000 - 0xefefffff (0x4100000) MX[B] (II) Bus 1 prefetchable memory range: [0] -1 0 0xdfc00000 - 0xe3cfffff (0x4100000) MX[B] (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (--) PCI:*(1:0:0) 3Dfx Interactive, Inc. Voodoo 3 rev 1, Mem @ 0xec000000/25, 0xe0000000/25, I/O @ 0xac00/8, BIOS @ 0xefef0000/15 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) PCI Memory resource overlap reduced 0xe4000000 from 0xe7ffffff to 0xe3ffffff (II) Active PCI resource ranges: [0] -1 0 0xeffebf00 - 0xeffebfff (0x100) MX[B] [1] -1 0 0xefff0000 - 0xefffffff (0x10000) MX[B] [2] -1 0 0xe4000000 - 0xe3ffffff (0x0) MX[B]O [3] -1 0 0xefef0000 - 0xefef7fff (0x8000) MX[B](B) [4] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B](B) [5] -1 0 0xec000000 - 0xedffffff (0x2000000) MX[B](B) [6] -1 0 0x0000d000 - 0x0000d03f (0x40) IX[B] [7] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B] [8] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [9] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B] [10] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B] [11] -1 0 0x0000ac00 - 0x0000acff (0x100) IX[B](B) (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xeffebf00 - 0xeffebfff (0x100) MX[B] [1] -1 0 0xefff0000 - 0xefffffff (0x10000) MX[B] [2] -1 0 0xe4000000 - 0xe3ffffff (0x0) MX[B]O [3] -1 0 0xefef0000 - 0xefef7fff (0x8000) MX[B](B) [4] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B](B) [5] -1 0 0xec000000 - 0xedffffff (0x2000000) MX[B](B) [6] -1 0 0x0000d000 - 0x0000d03f (0x40) IX[B] [7] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B] [8] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [9] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B] [10] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B] [11] -1 0 0x0000ac00 - 0x0000acff (0x100) IX[B](B) (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xeffebf00 - 0xeffebfff (0x100) MX[B] [6] -1 0 0xefff0000 - 0xefffffff (0x10000) MX[B] [7] -1 0 0xe4000000 - 0xe3ffffff (0x0) MX[B]O [8] -1 0 0xefef0000 - 0xefef7fff (0x8000) MX[B](B) [9] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B](B) [10] -1 0 0xec000000 - 0xedffffff (0x2000000) MX[B](B) [11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [13] -1 0 0x0000d000 - 0x0000d03f (0x40) IX[B] [14] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B] [15] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [16] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B] [17] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B] [18] -1 0 0x0000ac00 - 0x0000acff (0x100) IX[B](B) (II) LoadModule: "dbe" (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a (II) Module dbe: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a (II) Module extmod: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension DPMS (II) Loading extension FontCache (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "type1" (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a (II) Module type1: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.2 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font Type1 (II) Loading font CID (II) LoadModule: "speedo" (II) Loading /usr/X11R6/lib/modules/fonts/libspeedo.a (II) Module speedo: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.1 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font Speedo (II) LoadModule: "glx" (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a (II) Module glx: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading sub module "GLcore" (II) LoadModule: "GLcore" (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Module GLcore: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension GLX (II) LoadModule: "dri" (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a (II) Module dri: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a (II) Module drm: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension XFree86-DRI (II) LoadModule: "tdfx" (II) Loading /usr/X11R6/lib/modules/drivers/tdfx_drv.o (II) Module tdfx: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 Module class: XFree86 Video Driver ABI class: XFree86 Video Driver, version 0.6 (II) LoadModule: "mouse" (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o (II) Module mouse: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 Module class: XFree86 XInput Driver ABI class: XFree86 XInput driver, version 0.4 (II) TDFX: Driver for 3dfx Banshee/Voodoo3 chipsets: 3dfx Banshee, 3dfx Voodoo3, 3dfx Voodoo5 (II) Primary Device is: PCI 01:00:0 (--) Assigning device section with no busID to primary device (--) Chipset 3dfx Voodoo3 found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xeffebf00 - 0xeffebfff (0x100) MX[B] [6] -1 0 0xefff0000 - 0xefffffff (0x10000) MX[B] [7] -1 0 0xe4000000 - 0xe3ffffff (0x0) MX[B]O [8] -1 0 0xefef0000 - 0xefef7fff (0x8000) MX[B](B) [9] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B](B) [10] -1 0 0xec000000 - 0xedffffff (0x2000000) MX[B](B) [11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [13] -1 0 0x0000d000 - 0x0000d03f (0x40) IX[B] [14] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B] [15] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [16] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B] [17] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B] [18] -1 0 0x0000ac00 - 0x0000acff (0x100) IX[B](B) (II) resource ranges after probing: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xeffebf00 - 0xeffebfff (0x100) MX[B] [6] -1 0 0xefff0000 - 0xefffffff (0x10000) MX[B] [7] -1 0 0xe4000000 - 0xe3ffffff (0x0) MX[B]O [8] -1 0 0xefef0000 - 0xefef7fff (0x8000) MX[B](B) [9] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B](B) [10] -1 0 0xec000000 - 0xedffffff (0x2000000) MX[B](B) [11] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [12] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [13] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [16] -1 0 0x0000d000 - 0x0000d03f (0x40) IX[B] [17] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B] [18] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [19] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B] [20] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B] [21] -1 0 0x0000ac00 - 0x0000acff (0x100) IX[B](B) [22] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [23] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/X11R6/lib/modules/libvgahw.a (II) Module vgahw: vendor="The XFree86 Project" compiled for 4.3.0, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.6 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Loading /usr/X11R6/lib/modules/linux/libint10.a (II) Module int10: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.6 (II) TDFX(0): Softbooting the board (through the int10 interface). (II) TDFX(0): Primary V_BIOS segment is: 0xc000 (II) TDFX(0): Softbooting the board succeeded. (II) TDFX(0): TDFXFindChips: found 1 chip(s) (**) TDFX(0): Depth 16, (--) framebuffer bpp 16 (==) TDFX(0): RGB weight 565 (==) TDFX(0): Default visual is TrueColor (--) TDFX(0): Chipset: "3dfx Voodoo3" (--) TDFX(0): Linear framebuffer at 0xE0000000 (--) TDFX(0): MMIO registers at addr 0xEC000000 (--) TDFX(0): PIO registers at addr 0xAC00 (II) TDFX(0): DRAMINIT1 read 0x202031, programming 0x202031 (not Banshee) (II) TDFX(0): TDFXInitChips: numchips = 1 (II) TDFX(0): TDFXInitChips: cfgbits = 0x00000000, initbits = 0x00000001 (II) TDFX(0): TDFXInitChips: mem0base = 0xec000000, mem1base = 0xe0000008 (II) TDFX(0): TDFXInitChips: mem0size = 0x02000000, mem1size = 0x01000000 (II) TDFX(0): TDFXInitChips: mem0bits = 0x00000005, mem1bits = 0x00000060 (II) TDFX(0): TDFXInitChips: cfgbits = 0x00000065 (II) TDFX(0): TDFXInitChips: MMIOAddr[0] = 0xec000000 (II) TDFX(0): TDFXInitChips: LinearAddr[0] = 0xe0000008 (**) TDFX(0): VideoRAM: 8192 kByte Mapping 16384 kByte (==) TDFX(0): Using gamma correction (1.0, 1.0, 1.0) (II) TDFX(0): Flatron 795FT (LG): Using hsync range of 30.00-96.00 kHz (II) TDFX(0): Flatron 795FT (LG): Using vrefresh range of 50.00-160.00 Hz (II) TDFX(0): Clock range: 12.00 to 300.00 MHz (II) TDFX(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TDFX(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TDFX(0): Not using default mode "1600x1200" (hsync out of range) (II) TDFX(0): Not using default mode "800x600" (hsync out of range) (II) TDFX(0): Not using default mode "1792x1344" (hsync out of range) (II) TDFX(0): Not using default mode "896x672" (hsync out of range) (II) TDFX(0): Not using default mode "1856x1392" (hsync out of range) (II) TDFX(0): Not using default mode "928x696" (hsync out of range) (II) TDFX(0): Not using default mode "1920x1440" (hsync out of range) (II) TDFX(0): Not using default mode "960x720" (hsync out of range) (II) TDFX(0): Not using default mode "1400x1050" (unknown reason) (II) TDFX(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TDFX(0): Not using default mode "960x720" (hsync out of range) (II) TDFX(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TDFX(0): Not using default mode "1024x768" (hsync out of range) (II) TDFX(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TDFX(0): Not using default mode "1024x768" (hsync out of range) (II) TDFX(0): Not using default mode "2048x1536" (width too large for virtual size) (II) TDFX(0): Not using default mode "1920x1440" (width too large for virtual size) (II) TDFX(0): Not using default mode "1856x1392" (width too large for virtual size) (II) TDFX(0): Not using default mode "1792x1344" (width too large for virtual size) (II) TDFX(0): Not using default mode "1600x1200" (width too large for virtual size) (II) TDFX(0): Not using default mode "1600x1200" (width too large for virtual size) (II) TDFX(0): Not using default mode "1600x1200" (width too large for virtual size) (II) TDFX(0): Not using default mode "1600x1200" (width too large for virtual size) (II) TDFX(0): Not using default mode "1400x1050" (width too large for virtual size) (II) TDFX(0): Not using default mode "1280x1024" (width too large for virtual size) (II) TDFX(0): Not using default mode "1280x1024" (width too large for virtual size) (II) TDFX(0): Not using default mode "1280x1024" (width too large for virtual size) (II) TDFX(0): Not using default mode "1280x960" (width too large for virtual size) (II) TDFX(0): Not using default mode "1280x960" (width too large for virtual size) (--) TDFX(0): Virtual size is 1152x864 (pitch 1152) (**) TDFX(0): *Default mode "1152x864": 108.0 MHz, 67.5 kHz, 75.0 Hz (II) TDFX(0): Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (**) TDFX(0): *Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz (II) TDFX(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync (**) TDFX(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz (II) TDFX(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync (**) TDFX(0): *Default mode "640x480": 74.2 MHz, 85.9 kHz, 85.1 Hz (D) (II) TDFX(0): Modeline "640x480" 74.25 640 672 752 864 480 480 482 505 doublescan +hsync +vsync (**) TDFX(0): Default mode "1152x768": 65.0 MHz, 44.2 kHz, 54.8 Hz (II) TDFX(0): Modeline "1152x768" 65.00 1152 1178 1314 1472 768 771 777 806 +hsync +vsync (**) TDFX(0): Default mode "1024x768": 78.8 MHz, 60.1 kHz, 75.1 Hz (II) TDFX(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (**) TDFX(0): Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz (II) TDFX(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (**) TDFX(0): Default mode "1024x768": 133.5 MHz, 95.3 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "1024x768" 133.47 1024 1100 1212 1400 768 768 770 794 doublescan -hsync +vsync (**) TDFX(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz (II) TDFX(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (**) TDFX(0): Default mode "960x720": 117.0 MHz, 90.0 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "960x720" 117.00 960 1024 1128 1300 720 720 722 750 doublescan -hsync +vsync (**) TDFX(0): Default mode "928x696": 109.2 MHz, 86.4 kHz, 60.1 Hz (D) (II) TDFX(0): Modeline "928x696" 109.15 928 976 1088 1264 696 696 698 719 doublescan -hsync +vsync (**) TDFX(0): Default mode "896x672": 102.4 MHz, 83.7 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "896x672" 102.40 896 960 1060 1224 672 672 674 697 doublescan -hsync +vsync (**) TDFX(0): Default mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz (II) TDFX(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (**) TDFX(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (II) TDFX(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (**) TDFX(0): Default mode "800x600": 101.2 MHz, 93.8 kHz, 75.0 Hz (D) (II) TDFX(0): Modeline "800x600" 101.25 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (**) TDFX(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (II) TDFX(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (**) TDFX(0): Default mode "800x600": 94.5 MHz, 87.5 kHz, 70.0 Hz (D) (II) TDFX(0): Modeline "800x600" 94.50 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (**) TDFX(0): Default mode "800x600": 87.8 MHz, 81.2 kHz, 65.0 Hz (D) (II) TDFX(0): Modeline "800x600" 87.75 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (**) TDFX(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (II) TDFX(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (**) TDFX(0): Default mode "800x600": 81.0 MHz, 75.0 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "800x600" 81.00 800 832 928 1080 600 600 602 625 doublescan +hsync +vsync (**) TDFX(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (II) TDFX(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (**) TDFX(0): Default mode "700x525": 77.9 MHz, 81.5 kHz, 74.8 Hz (D) (II) TDFX(0): Modeline "700x525" 77.90 700 732 892 956 525 526 532 545 doublescan +hsync +vsync (**) TDFX(0): Default mode "700x525": 61.0 MHz, 64.9 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "700x525" 61.00 700 744 820 940 525 526 532 541 doublescan +hsync +vsync (**) TDFX(0): Default mode "640x512": 78.8 MHz, 91.1 kHz, 85.0 Hz (D) (II) TDFX(0): Modeline "640x512" 78.75 640 672 752 864 512 512 514 536 doublescan +hsync +vsync (**) TDFX(0): Default mode "640x512": 67.5 MHz, 80.0 kHz, 75.0 Hz (D) (II) TDFX(0): Modeline "640x512" 67.50 640 648 720 844 512 512 514 533 doublescan +hsync +vsync (**) TDFX(0): Default mode "640x512": 54.0 MHz, 64.0 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "640x512" 54.00 640 664 720 844 512 512 514 533 doublescan +hsync +vsync (**) TDFX(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (II) TDFX(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (**) TDFX(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (II) TDFX(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (**) TDFX(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (II) TDFX(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (**) TDFX(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (II) TDFX(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (**) TDFX(0): Default mode "640x480": 54.0 MHz, 60.0 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "640x480" 54.00 640 688 744 900 480 480 482 500 doublescan +hsync +vsync (**) TDFX(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (II) TDFX(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (**) TDFX(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TDFX(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (**) TDFX(0): Default mode "576x432": 54.0 MHz, 67.5 kHz, 75.0 Hz (D) (II) TDFX(0): Modeline "576x432" 54.00 576 608 672 800 432 432 434 450 doublescan +hsync +vsync (**) TDFX(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TDFX(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (**) TDFX(0): Default mode "576x384": 32.5 MHz, 44.2 kHz, 54.8 Hz (D) (II) TDFX(0): Modeline "576x384" 32.50 576 589 657 736 384 385 388 403 doublescan +hsync +vsync (**) TDFX(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D) (II) TDFX(0): Modeline "512x384" 47.25 512 536 584 688 384 384 386 404 doublescan +hsync +vsync (**) TDFX(0): Default mode "512x384": 39.4 MHz, 60.1 kHz, 75.1 Hz (D) (II) TDFX(0): Modeline "512x384" 39.40 512 520 568 656 384 384 386 400 doublescan +hsync +vsync (**) TDFX(0): Default mode "512x384": 37.5 MHz, 56.5 kHz, 70.1 Hz (D) (II) TDFX(0): Modeline "512x384" 37.50 512 524 592 664 384 385 388 403 doublescan -hsync -vsync (**) TDFX(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D) (II) TDFX(0): Modeline "512x384" 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync (**) TDFX(0): Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D) (II) TDFX(0): Modeline "416x312" 28.64 416 432 464 576 312 312 314 333 doublescan -hsync -vsync (**) TDFX(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D) (II) TDFX(0): Modeline "400x300" 28.15 400 416 448 524 300 300 302 315 doublescan +hsync +vsync (**) TDFX(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D) (II) TDFX(0): Modeline "400x300" 24.75 400 408 448 528 300 300 302 312 doublescan +hsync +vsync (**) TDFX(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D) (II) TDFX(0): Modeline "400x300" 25.00 400 428 488 520 300 318 321 333 doublescan +hsync +vsync (**) TDFX(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D) (II) TDFX(0): Modeline "400x300" 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync (**) TDFX(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D) (II) TDFX(0): Modeline "400x300" 18.00 400 412 448 512 300 300 301 312 doublescan +hsync +vsync (**) TDFX(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D) (II) TDFX(0): Modeline "320x240" 18.00 320 348 376 416 240 240 242 254 doublescan -hsync -vsync (**) TDFX(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D) (II) TDFX(0): Modeline "320x240" 15.75 320 328 360 420 240 240 242 250 doublescan -hsync -vsync (**) TDFX(0): Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D) (II) TDFX(0): Modeline "320x240" 15.75 320 332 352 416 240 244 245 260 doublescan -hsync -vsync (**) TDFX(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D) (II) TDFX(0): Modeline "320x240" 12.60 320 328 376 400 240 245 246 262 doublescan -hsync -vsync (**) TDFX(0): Default mode "360x200": 17.8 MHz, 37.9 kHz, 85.0 Hz (D) (II) TDFX(0): Modeline "360x200" 17.75 360 378 414 468 200 200 202 223 doublescan -hsync +vsync (**) TDFX(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (II) TDFX(0): Modeline "320x200" 15.75 320 336 368 416 200 200 202 222 doublescan -hsync +vsync (**) TDFX(0): Default mode "320x175": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (II) TDFX(0): Modeline "320x175" 15.75 320 336 368 416 175 191 192 222 doublescan +hsync -vsync (==) TDFX(0): DPI set to (75, 75) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/X11R6/lib/modules/libfb.a (II) Module fb: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 ANSI C Emulation, version 0.2 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/X11R6/lib/modules/libxaa.a (II) Module xaa: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.1.0 ABI class: XFree86 Video Driver, version 0.6 (**) TDFX(0): ShowCache Disabled (**) TDFX(0): video key default 0x1e (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/X11R6/lib/modules/libramdac.a (II) Module ramdac: vendor="The XFree86 Project" compiled for 4.3.0, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.6 (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11R6/lib/modules/libddc.a (II) Module ddc: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.6 (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/X11R6/lib/modules/libvbe.a (II) Module vbe: vendor="The XFree86 Project" compiled for 4.3.0, module version = 1.1.0 ABI class: XFree86 Video Driver, version 0.6 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Reloading /usr/X11R6/lib/modules/linux/libint10.a (II) TDFX(0): initializing int10 (II) TDFX(0): Primary V_BIOS segment is: 0xc000 (EE) TDFX(0): unknown reason for exception (II) TDFX(0): EAX=0x00000000, EBX=0x00002000, ECX=0x00000000, EDX=0x00000000 (II) TDFX(0): ESP=0x00000fe0, EBP=0x00000000, ESI=0x00000016, EDI=0x000020f2 (II) TDFX(0): CS=0xc000, SS=0x0100, DS=0xc000, ES=0x0000, FS=0x0000, GS=0x0000 (II) TDFX(0): EIP=0x0000ffff, EFLAGS=0x00033246 (II) stack at 0x00001fe0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff (II) TDFX(0): code at 0x000cffff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff (EE) TDFX(0): cannot continue (II) TDFX(0): VESA BIOS not detected (II) do I need RAC? No, I don't. (II) resource ranges after preInit: [0] 0 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B] [1] 0 0 0xec000000 - 0xedffffff (0x2000000) MX[B] [2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [7] -1 0 0xeffebf00 - 0xeffebfff (0x100) MX[B] [8] -1 0 0xefff0000 - 0xefffffff (0x10000) MX[B] [9] -1 0 0xe4000000 - 0xe3ffffff (0x0) MX[B]O [10] -1 0 0xefef0000 - 0xefef7fff (0x8000) MX[B](B) [11] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B](B) [12] -1 0 0xec000000 - 0xedffffff (0x2000000) MX[B](B) [13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [16] 0 0 0x0000ac00 - 0x0000acff (0x100) IX[B] [17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [18] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [19] -1 0 0x0000d000 - 0x0000d03f (0x40) IX[B] [20] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B] [21] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [22] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B] [23] -1 0 0x0000ffa0 - 0x0000ffaf (0x10) IX[B] [24] -1 0 0x0000ac00 - 0x0000acff (0x100) IX[B](B) [25] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprD) [26] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprD) (==) TDFX(0): Write-combining range (0xe0000000,0x1000000) (II) TDFX(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0xa900 (II) TDFX(0): Changing back offset from 0x00433000 to 0x00432000 (II) TDFX(0): Textures Memory 1.38 MB (II) TDFX(0): Cursor Offset: [0x00000000,0x00001000) (II) TDFX(0): Fifo Offset: [0x00001000, 0x00041000) (II) TDFX(0): Front Buffer Offset: [0x00041000, 0x002CFC00) (II) TDFX(0): Texture Offset: [0x002CFC00, 0x00432000) (II) TDFX(0): BackOffset: [0x00432000, 0x00618000) (II) TDFX(0): DepthOffset: [0x00619000, 0x007FF000) (II) TDFX(0): Minimum 300, Maximum 929 lines of offscreen memory available drmOpenDevice: minor is 0 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is 6, (OK) drmOpenDevice: minor is 0 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is 6, (OK) drmOpenDevice: minor is 0 drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is 6, (OK) drmGetBusid returned '' (II) TDFX(0): [drm] created "tdfx" driver at busid "PCI:1:0:0" (II) TDFX(0): [drm] added 8192 byte SAREA at 0xcca7f000 (II) TDFX(0): [drm] mapped SAREA 0xcca7f000 to 0x40016000 (II) TDFX(0): [drm] framebuffer handle = 0xe0000000 (II) TDFX(0): [drm] added 1 reserved context for kernel (II) TDFX(0): [drm] Registers = 0xec000000 (II) TDFX(0): visual configs initialized (II) TDFX(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Dashed Lines Offscreen Pixmaps Driver provided NonTEGlyphRenderer replacement Setting up tile and stipple cache: 32 128x128 slots 7 256x256 slots (==) TDFX(0): Backing store disabled (==) TDFX(0): Silken mouse enabled (II) TDFX(0): X context handle = 0x00000001 (II) TDFX(0): [drm] installed DRM signal handler (II) TDFX(0): [DRI] installation complete (==) TDFX(0): Direct rendering enabled (==) RandR enabled (II) Setting vga for screen 0. (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension LBX (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (**) Option "Protocol" "IMPS/2" (**) Mouse1: Protocol: "IMPS/2" (**) Option "CorePointer" (**) Mouse1: Core Pointer (**) Option "Device" "/dev/mouse" (**) Mouse1: Emulate3Buttons, Emulate3Timeout: 50 (**) Option "ZAxisMapping" "4 5" (**) Mouse1: ZAxisMapping: buttons 4 and 5 (**) Mouse1: Buttons: 5 (II) Keyboard "Keyboard1" handled by legacy driver (II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE) (II) Mouse1: ps2EnableDataReporting: succeeded SetClientVersion: 0 7 (WW) Open APM failed (/dev/apm_bios) (No such device) (II) Mouse1: ps2EnableDataReporting: succeeded (WW) Open APM failed (/dev/apm_bios) (No such device) (II) Mouse1: ps2EnableDataReporting: succeeded ----------------------------------------------------------------------------------------------- XF86Config : ----------------- # File generated by xf86config. # # Copyright (c) 1999 by The XFree86 Project, Inc. # # Permission is hereby granted, free of charge, to any person obtaining a # copy of this software and associated documentation files (the "Software"), # to deal in the Software without restriction, including without limitation # the rights to use, copy, modify, merge, publish, distribute, sublicense, # and/or sell copies of the Software, and to permit persons to whom the # Software is furnished to do so, subject to the following conditions: # # The above copyright notice and this permission notice shall be included in # all copies or substantial portions of the Software. # # THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR # IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, # FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL # THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, # WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF # OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE # SOFTWARE. # # Except as contained in this notice, the name of the XFree86 Project shall # not be used in advertising or otherwise to promote the sale, use or other # dealings in this Software without prior written authorization from the # XFree86 Project. # # ********************************************************************** # Refer to the XF86Config(4/5) man page for details about the format of # this file. # ********************************************************************** # ********************************************************************** # Module section -- this section is used to specify # which dynamically loadable modules to load. # ********************************************************************** # Section "Module" # This loads the DBE extension module. Load "dbe" # Double buffer extension # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection # This loads the Type1 and FreeType font modules Load "type1" Load "speedo" # Load "freetype" # Load "xtt" # This loads the GLX module Load "glx" # This loads the DRI module Load "dri" EndSection # ********************************************************************** # Files section. This allows default font and rgb paths to be set # ********************************************************************** Section "Files" # The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default. RgbPath "/usr/X11R6/lib/X11/rgb" # Multiple FontPath entries are allowed (which are concatenated together), # as well as specifying multiple comma-separated entries in one FontPath # command (or a combination of both methods) # # If you don't have a floating point coprocessor and emacs, Mosaic or other # programs take long to start up, try moving the Type1 and Speedo directory # to the end of this list (or comment them out). # FontPath "/usr/X11R6/lib/X11/fonts/local/" FontPath "/usr/X11R6/lib/X11/fonts/misc/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/Speedo/" FontPath "/usr/X11R6/lib/X11/fonts/Type1/" # FontPath "/usr/X11R6/lib/X11/fonts/TrueType/" # FontPath "/usr/X11R6/lib/X11/fonts/freefont/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" # FontPath "/usr/X11R6/lib/X11/fonts/100dpi/" # The module search path. The default path is shown here. # ModulePath "/usr/X11R6/lib/modules" EndSection # ********************************************************************** # Server flags section. # ********************************************************************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # Option "NoTrapSignals" # Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence # (where n is 1 through 12). This allows clients to receive these key # events. # Option "DontVTSwitch" # Uncomment this to disable the <Crtl><Alt><BS> server abort sequence # This allows clients to receive this key event. # Option "DontZap" # Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching # sequences. This allows clients to receive these key events. # Option "Dont Zoom" # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # Option "DisableVidModeExtension" # Uncomment this to enable the use of a non-local xvidtune client. # Option "AllowNonLocalXvidtune" # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # Option "DisableModInDev" # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # Option "AllowNonLocalModInDev" EndSection # ********************************************************************** # Input devices # ********************************************************************** # ********************************************************************** # Core keyboard's InputDevice section # ********************************************************************** Section "InputDevice" Identifier "Keyboard1" Driver "Keyboard" # For most OSs the protocol can be omitted (it defaults to "Standard"). # When using XQUEUE (only for SVR3 and SVR4, but not Solaris), # uncomment the following line. # Option "Protocol" "Xqueue" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # Option "LeftAlt" "Meta" # Option "RightAlt" "ModeShift" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc102" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for XFree86 # Option "XkbRules" "xfree86" # Option "XkbModel" "pc101" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" # Option "XkbDisable" Option "XkbRules" "xfree86" Option "XkbModel" "pc102" Option "XkbLayout" "fr" EndSection # ********************************************************************** # Core Pointer's InputDevice section # ********************************************************************** Section "InputDevice" # Identifier and driver Identifier "Mouse1" Driver "mouse" Option "Protocol" "IMPS/2" Option "Device" "/dev/mouse" Option "ZAxisMapping" "4 5" # Mouse-speed setting for PS/2 mouse. # Option "Resolution" "256" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" EndSection # ********************************************************************** # Other input device sections # this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the XF86Config man page for a description of the options. # ********************************************************************** # # Section "InputDevice" # Identifier "Mouse2" # Driver "mouse" # Option "Protocol" "MouseMan" # Option "Device" "/dev/mouse2" # EndSection # # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ********************************************************************** # Monitor section # ********************************************************************** # Any number of monitor sections may be present Section "Monitor" Identifier "Flatron 795FT (LG)" # HorizSync is in kHz unless units are specified. # HorizSync may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. HorizSync 30-96 # HorizSync 30-64 # multisync # HorizSync 31.5, 35.2 # multiple fixed sync frequencies # HorizSync 15-25, 30-50 # multiple ranges of sync frequencies # VertRefresh is in Hz unless units are specified. # VertRefresh may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. VertRefresh 50-160 EndSection # ********************************************************************** # Graphics device section # ********************************************************************** # Any number of graphics device sections may be present # Standard VGA Device: Section "Device" Identifier "Standard VGA" VendorName "Unknown" BoardName "Unknown" # The chipset line is optional in most cases. It can be used to override # the driver's chipset detection, and should not normally be specified. # Chipset "generic" # The Driver line must be present. When using run-time loadable driver # modules, this line instructs the server to load the specified driver # module. Even when not using loadable driver modules, this line # indicates which driver should interpret the information in this section. Driver "vga" # The BusID line is used to specify which of possibly multiple devices # this section is intended for. When this line isn't present, a device # section can only match up with the primary video device. For PCI # devices a line like the following could be used. This line should not # normally be included unless there is more than one video device # intalled. # BusID "PCI:0:10:0" # VideoRam 256 # Clocks 25.2 28.3 EndSection # Device configured by xf86config: Section "Device" Identifier "Voodoo3 (generic)" Driver "tdfx" VideoRam 8192 # Insert Clocks lines here if appropriate EndSection # ********************************************************************** # Screen sections # ********************************************************************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. Section "Screen" Identifier "Screen 1" Device "Voodoo3 (generic)" Monitor "Flatron 795FT (LG)" DefaultDepth 16 # Subsection "Display" # Depth 8 # Modes "1280x1024" "1024x768" "800x600" "640x480" # ViewPort 0 0 # EndSubsection Subsection "Display" Depth 16 Modes "1152x864" "1024x768" "800x600" "640x480" ViewPort 0 0 EndSubsection # Subsection "Display" # Depth 24 # Modes "1280x1024" "1024x768" "800x600" "640x480" # ViewPort 0 0 # EndSubsection EndSection # ********************************************************************** # ServerLayout sections. # ********************************************************************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. Section "ServerLayout" # The Identifier line must be present Identifier "Simple Layout" # Each Screen line specifies a Screen section name, and optionally # the relative position of other screens. The four names after # primary screen name are the screens to the top, bottom, left and right # of the primary screen. In this example, screen 2 is located to the # right of screen 1. Screen "Screen 1" # Each InputDevice line specifies an InputDevice section name and # optionally some options to specify the way the device is to be # used. Those options include "CorePointer", "CoreKeyboard" and # "SendCoreEvents". InputDevice "Mouse1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection Section "DRI" Mode 0666 EndSection _______________________________________________ XFree86 mailing list XFree86@xxxxxxxxxxx http://XFree86.Org/mailman/listinfo/xfree86
