Sent to Mr. Brosius in private first, but yes, it's a better idea to send it to a wider audience. In addition to the below, I'll mention that the 'red dots' seem to mainly show up where I have a dark color on screen; most notably seen in my XMMS skin which is a lot of dark and mid-bright browns. Something of interest is that not _every_ pixel has the distortion: On a long line of same-colored pixels, the dots (*) is distributed something like: "----*---*--**-----*----*---------*------*----**---*---*" And they stay like that even if I move the window! Ie, not dependant on the window being in a certain position on screen. ---------- Forwarded message ---------- Date: Tue, 23 Sep 2003 02:43:27 +0200 (CEST) From: Henrik 'Snout' Isacsson <snout@xxxxxxxxxxxxx> To: Kevin Brosius <cobra@xxxxxxxxxxxxxx> Cc: snout@xxxxxxxxxxxxx Subject: Re: S3 Virge driver on 86e280 > > Hi there! I have a laptop with an S3 86e280 chip in it, like the fellow in > > <http://xfree86.desiato.de/xfree86/pipermail/xpert/2001-December/013691.html> > > reported about. > Hi Henrik, > Any reason you didn't copy this to the trouble report mail list? I'd > prefer that everyone benefit from responses. Oops. My bad there.. I can repost there, for sure. I'll put in my replies to your questions too, so you won't have to repeat those. It seems best to me to add to the thread at http://xfree86.desiato.de/xfree86/pipermail/xpert/2001-December/013714.html since that's where the "remove VBE" tip was that helped me, too. Umm. This might sound stupid, but how do I add to the thread? I see no "reply" on the web page; do I mail to "devel@xxxxxxxxxxx", or some other address? > Have you tried 4.3.0? Are these new problems in CVS or do they also > happen in 4.3.0? The lockup has happened since 4.0.3, pretty much 4.* I've tried since 3.3.6. (3.3.6 works fine, but isn't as accelerated as I'd like.. ie, slow.) > For the red dots, try the option: > > option "xvideo" "off" > > in the driver section, does that help? No, same red dots. > Also, how much video ram do you think the card has? The log reports > 4M. Do you think it rally has 4M in the laptop? As far as I understand, it has 4 or 8MB in it. Hmm. I can run 800x600x24bpp, but that's only 1.4MB so it doesn't really say much. I have the '8MB' figure from the previous owner of the laptop who ran Win98 on it. Since I installed a too big harddrive for the BIOS to handle, I can't boot Win98 and see what it reports even, only linux works on it now. Not much help there.. ============== XFree.0.log : This is a pre-release version of XFree86, and is not supported in any way. Bugs may be reported to XFree86@xxxxxxxxxxx and patches submitted to fixes@xxxxxxxxxxxx Before reporting bugs in pre-release versions, please check the latest version in the XFree86 CVS repository (http://www.XFree86.Org/cvs). XFree86 Version 4.3.99.12 Release Date: 10 September 2003 X Protocol Version 11, Revision 0, Release 6.6 Build Operating System: Linux 2.4.22-ck2 i586 [ELF] Current Operating System: Linux laptop 2.4.22-ck2 #4 sön sep 21 19:08:28 CEST 20 03 i586 Build Date: 22 September 2003 Changelog Date: 10 September 2003 Before reporting problems, check http://www.XFree86.Org/ to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/XFree86.0.log", Time: Tue Sep 23 03:44:26 2003 (==) Using config file: "/etc/X11/XF86Config-4" (==) ServerLayout "Default Layout" (**) |-->Screen "Default Screen" (0) (**) | |-->Monitor "Generic Monitor" (**) | |-->Device "Generic Video Card" (**) |-->Input Device "Generic Keyboard" (**) Option "XkbRules" "xfree86" (**) XKB: rules: "xfree86" (**) Option "XkbModel" "pc104" (**) XKB: model: "pc104" (**) Option "XkbLayout" "us" (**) XKB: layout: "us" (==) Keyboard: CustomKeycode disabled (**) |-->Input Device "Configured Mouse" (**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc,/usr/X11R6/lib/X11/fonts/cyr illic,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/75dpi/: unscaled,/usr/X11R6/lib/X11/fonts/Type1,/usr/X11R6/lib/X11/fonts/Speedo,/usr/X11 R6/lib/X11/fonts/100dpi,/usr/X11R6/lib/X11/fonts/75dpi" (==) RgbPath set to "/usr/X11R6/lib/X11/rgb" (==) ModulePath set to "/usr/X11R6/lib/modules" (--) using VT number 3 (II) Open APM successful (II) Module ABI versions: XFree86 ANSI C Emulation: 0.2 XFree86 Video Driver: 0.7 XFree86 XInput driver : 0.4 XFree86 Server Extension : 0.2 XFree86 Font Renderer : 0.4 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Module bitmap: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11R6/lib/modules/libpcidata.a (II) Module pcidata: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.7 (II) PCI: Probing config type using method 1 (II) PCI: Config type is 1 (II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 8086,7100 card 0000,0000 rev 01 class 06,00,00 hdr 00 (II) PCI: 00:02:0: chip 5333,8c03 card 5333,8c03 rev 03 class 03,00,00 hdr 00 (II) PCI: 00:03:0: chip 104c,ac16 card 0000,0000 rev 02 class 06,07,00 hdr 82 (II) PCI: 00:03:1: chip 104c,ac16 card 0000,0000 rev 02 class 06,07,00 hdr 82 (II) PCI: 00:07:0: chip 8086,7110 card 0000,0000 rev 01 class 06,01,00 hdr 80 (II) PCI: 00:07:1: chip 8086,7111 card 0000,0000 rev 01 class 01,01,80 hdr 00 (II) PCI: 00:07:2: chip 8086,7112 card 0000,0000 rev 01 class 0c,03,00 hdr 00 (II) PCI: 00:07:3: chip 8086,7113 card 0000,0000 rev 01 class 06,80,00 hdr 00 (II) PCI: End of PCI scan (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (0,0,5), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) PCI-to-CardBus bridge: (II) Bus 1: bridge is at (0:3:0), (0,1,4), BCTRL: 0x07c0 (VGA_EN is cleared) (II) PCI-to-CardBus bridge: (II) Bus 5: bridge is at (0:3:1), (0,5,8), BCTRL: 0x07c0 (VGA_EN is cleared) (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (--) PCI:*(0:2:0) S3 Inc. ViRGE/MX+MV rev 3, Mem @ 0xc0000000/26, BIOS @ 0x000c0 000/16 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) Active PCI resource ranges: [0] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [1] -1 0 0xc0000000 - 0xc3ffffff (0x4000000) MX[B](B) [2] -1 0 0x0000f300 - 0x0000f31f (0x20) IX[B] [3] -1 0 0x00001100 - 0x0000110f (0x10) IX[B] (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [1] -1 0 0xc0000000 - 0xc3ffffff (0x4000000) MX[B](B) [2] -1 0 0x0000f300 - 0x0000f31f (0x20) IX[B] [3] -1 0 0x00001100 - 0x0000110f (0x10) IX[B] (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [6] -1 0 0xc0000000 - 0xc3ffffff (0x4000000) MX[B](B) [7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [8] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [9] -1 0 0x0000f300 - 0x0000f31f (0x20) IX[B] [10] -1 0 0x00001100 - 0x0000110f (0x10) IX[B] (II) LoadModule: "GLcore" (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Module GLcore: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) LoadModule: "bitmap" (II) Reloading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Loading font Bitmap (II) LoadModule: "dri" (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a (II) Module dri: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a (II) Module drm: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension XFree86-DRI (II) LoadModule: "extmod" (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a (II) Module extmod: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension FontCache (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "freetype" (II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a (II) Module freetype: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 2.0.4 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font FreeType (II) LoadModule: "glx" (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a (II) Module glx: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 Server Extension, version 0.2 (II) Loading sub module "GLcore" (II) LoadModule: "GLcore" (II) Reloading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Loading extension GLX (II) LoadModule: "int10" (II) Loading /usr/X11R6/lib/modules/linux/libint10.a (II) Module int10: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 Video Driver, version 0.7 (II) LoadModule: "record" (II) Loading /usr/X11R6/lib/modules/extensions/librecord.a (II) Module record: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.13.0 Module class: XFree86 Server Extension ABI class: XFree86 Server Extension, version 0.2 (II) Loading extension RECORD (II) LoadModule: "speedo" (II) Loading /usr/X11R6/lib/modules/fonts/libspeedo.a (II) Module speedo: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.1 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font Speedo (II) LoadModule: "type1" (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a (II) Module type1: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.2 Module class: XFree86 Font Renderer ABI class: XFree86 Font Renderer, version 0.4 (II) Loading font Type1 (II) Loading font CID (II) LoadModule: "s3virge" (II) Loading /usr/X11R6/lib/modules/drivers/s3virge_drv.o (II) Module s3virge: vendor="Kevin Brosius" compiled for 4.2.99.4, module version = 1.8.6 Module class: XFree86 Video Driver ABI class: XFree86 Video Driver, version 0.6 (II) LoadModule: "mouse" (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o (II) Module mouse: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 Module class: XFree86 XInput Driver ABI class: XFree86 XInput driver, version 0.4 (II) S3VIRGE: driver (version 1.8.6) for S3 ViRGE chipsets: virge, 86C325, virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2, 86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365, trio 3d/2x, 86C362, 86C368 (II) Primary Device is: PCI 00:02:0 (--) Assigning device section with no busID to primary device (--) Chipset virge mx+ found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [6] -1 0 0xc0000000 - 0xc3ffffff (0x4000000) MX[B](B) [7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [8] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [9] -1 0 0x0000f300 - 0x0000f31f (0x20) IX[B] [10] -1 0 0x00001100 - 0x0000110f (0x10) IX[B] (II) resource ranges after probing: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [6] -1 0 0xc0000000 - 0xc3ffffff (0x4000000) MX[B](B) [7] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [8] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [9] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000f300 - 0x0000f31f (0x20) IX[B] [13] -1 0 0x00001100 - 0x0000110f (0x10) IX[B] [14] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [15] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/X11R6/lib/modules/libvgahw.a (II) Module vgahw: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.7 (**) S3VIRGE(0): Depth 24, (--) framebuffer bpp 24 (==) S3VIRGE(0): RGB weight 888 (==) S3VIRGE(0): Default visual is TrueColor (**) S3VIRGE(0): Option "pci_burst" "on" (**) S3VIRGE(0): Option "fifo_aggressive" (**) S3VIRGE(0): Option: pci_burst - PCI burst read enabled (**) S3VIRGE(0): Option: fifo_aggressive set (==) S3VIRGE(0): Using HW Cursor (==) S3VIRGE(0): Using fb. (==) S3VIRGE(0): mx_cr3a_fix. (II) Loading sub module "vbe" (II) LoadModule: "vbe" (WW) Warning, couldn't open module vbe (II) UnloadModule: "vbe" (EE) S3VIRGE: Failed to load module "vbe" (module does not exist, 0) (--) S3VIRGE(0): Chipset: "virge mx+" (==) S3VIRGE(0): XVideo supported. (WW) System lacks support for changing MTRRs (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) Loading sub module "ddc" (II) LoadModule: "ddc" (WW) Warning, couldn't open module ddc (II) UnloadModule: "ddc" (EE) S3VIRGE: Failed to load module "ddc" (module does not exist, 0) (==) S3VIRGE(0): Using gamma correction (1.0, 1.0, 1.0) (--) S3VIRGE(0): videoram: 4096k (--) S3VIRGE(0): assuming RefCLK value of 14.318 MHz (--) S3VIRGE(0): Detected current MCLK value of 83.045 MHz (--) S3VIRGE(0): LCD size 800x600, clock 39.972 MHz (II) S3VIRGE(0): Generic Monitor: Using hsync range of 31.50-49.00 kHz (II) S3VIRGE(0): Generic Monitor: Using vrefresh range of 50.00-90.00 Hz (II) S3VIRGE(0): Clock range: 10.00 to 270.00 MHz (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "400x300" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "512x384" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "512x384" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "512x384" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1152x864" (hsync out of range) (II) S3VIRGE(0): Not using default mode "576x432" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1280x960" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x480" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1280x960" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x480" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x512" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x512" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range) (II) S3VIRGE(0): Not using default mode "640x512" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1600x1200" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "800x600" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "896x672" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "896x672" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "928x696" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "928x696" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "960x720" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "960x720" (hsync out of range) (II) S3VIRGE(0): Not using default mode "832x624" (hsync out of range) (II) S3VIRGE(0): Not using default mode "416x312" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1400x1050" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "700x525" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1400x1050" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "700x525" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1600x1024" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "800x512" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "960x720" (hsync out of range) (II) S3VIRGE(0): Not using default mode "2048x1536" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "2048x1536" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "2048x1536" (insufficient memory for mod e) (II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range) (II) S3VIRGE(0): Not using default mode "1152x768" (width too large for virtual size) (II) S3VIRGE(0): Not using default mode "1024x768" (width too large for virtual size) (II) S3VIRGE(0): Not using default mode "1024x768" (width too large for virtual size) (--) S3VIRGE(0): Virtual size is 800x600 (pitch 800) (**) S3VIRGE(0): *Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (II) S3VIRGE(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 + hsync +vsync (**) S3VIRGE(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (II) S3VIRGE(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -h sync -vsync (**) S3VIRGE(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (II) S3VIRGE(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 + hsync +vsync (**) S3VIRGE(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (II) S3VIRGE(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 + hsync +vsync (**) S3VIRGE(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (II) S3VIRGE(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 + hsync +vsync (**) S3VIRGE(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (II) S3VIRGE(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -h sync -vsync (**) S3VIRGE(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (II) S3VIRGE(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -h sync -vsync (**) S3VIRGE(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (II) S3VIRGE(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -h sync -vsync (**) S3VIRGE(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (II) S3VIRGE(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -h sync +vsync (**) S3VIRGE(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) S3VIRGE(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -h sync +vsync (**) S3VIRGE(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) S3VIRGE(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +h sync -vsync (**) S3VIRGE(0): Default mode "576x384": 32.5 MHz, 44.2 kHz, 54.8 Hz (D) (II) S3VIRGE(0): Modeline "576x384" 32.50 576 589 657 736 384 385 388 403 do ublescan +hsync +vsync (**) S3VIRGE(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D) (II) S3VIRGE(0): Modeline "512x384" 32.50 512 524 592 672 384 385 388 403 do ublescan -hsync -vsync (**) S3VIRGE(0): Default mode "512x384": 22.4 MHz, 35.5 kHz, 87.1 Hz (D) (II) S3VIRGE(0): Modeline "512x384" 22.45 512 516 604 632 384 384 388 409 in terlace doublescan +hsync +vsync (**) S3VIRGE(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D) (II) S3VIRGE(0): Modeline "400x300" 24.75 400 408 448 528 300 300 302 312 do ublescan +hsync +vsync (**) S3VIRGE(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D) (II) S3VIRGE(0): Modeline "400x300" 25.00 400 428 488 520 300 318 321 333 do ublescan +hsync +vsync (**) S3VIRGE(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D) (II) S3VIRGE(0): Modeline "400x300" 20.00 400 420 484 528 300 300 302 314 do ublescan +hsync +vsync (**) S3VIRGE(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D) (II) S3VIRGE(0): Modeline "400x300" 18.00 400 412 448 512 300 300 301 312 do ublescan +hsync +vsync (**) S3VIRGE(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D) (II) S3VIRGE(0): Modeline "320x240" 18.00 320 348 376 416 240 240 242 254 do ublescan -hsync -vsync (**) S3VIRGE(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D) (II) S3VIRGE(0): Modeline "320x240" 15.75 320 328 360 420 240 240 242 250 do ublescan -hsync -vsync (**) S3VIRGE(0): Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D) (II) S3VIRGE(0): Modeline "320x240" 15.75 320 332 352 416 240 244 245 260 do ublescan -hsync -vsync (**) S3VIRGE(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D) (II) S3VIRGE(0): Modeline "320x240" 12.60 320 328 376 400 240 245 246 262 do ublescan -hsync -vsync (**) S3VIRGE(0): Default mode "360x200": 17.8 MHz, 37.9 kHz, 85.0 Hz (D) (II) S3VIRGE(0): Modeline "360x200" 17.75 360 378 414 468 200 200 202 223 do ublescan -hsync +vsync (**) S3VIRGE(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (II) S3VIRGE(0): Modeline "320x200" 15.75 320 336 368 416 200 200 202 222 do ublescan -hsync +vsync (**) S3VIRGE(0): Default mode "320x175": 15.8 MHz, 37.9 kHz, 85.3 Hz (D) (II) S3VIRGE(0): Modeline "320x175" 15.75 320 336 368 416 175 191 192 222 do ublescan +hsync -vsync (++) S3VIRGE(0): DPI set to (100, 100) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/X11R6/lib/modules/libfb.a (II) Module fb: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.0.0 ABI class: XFree86 ANSI C Emulation, version 0.2 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/X11R6/lib/modules/libxaa.a (II) Module xaa: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 1.1.0 ABI class: XFree86 Video Driver, version 0.7 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/X11R6/lib/modules/libramdac.a (II) Module ramdac: vendor="The XFree86 Project" compiled for 4.3.99.12, module version = 0.1.0 ABI class: XFree86 Video Driver, version 0.7 (==) Depth 24 pixmap format is 32 bpp (II) do I need RAC? No, I don't. (II) resource ranges after preInit: [0] 0 0 0xc0000000 - 0xc3ffffff (0x4000000) MS[B] [1] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [4] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B] [5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [6] -1 0 0x000c0000 - 0x000cffff (0x10000) MX[B](B) [7] -1 0 0xc0000000 - 0xc3ffffff (0x4000000) MX[B](B) [8] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD) [9] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD) [10] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD) [11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [13] -1 0 0x0000f300 - 0x0000f31f (0x20) IX[B] [14] -1 0 0x00001100 - 0x0000110f (0x10) IX[B] [15] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU) [16] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU) (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (**) S3VIRGE(0): Using FB (II) S3VIRGE(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles CPU to Screen color expansion Solid Horizontal and Vertical Lines Image Writes Offscreen Pixmaps Setting up tile and stipple cache: 24 128x128 slots 6 256x256 slots (==) S3VIRGE(0): Backing store disabled (==) S3VIRGE(0): Silken mouse enabled (II) S3VIRGE(0): Using overlay video (==) RandR enabled (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension LBX (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Keyboard "Generic Keyboard" handled by legacy driver (**) Option "Protocol" "PS/2" (**) Configured Mouse: Protocol: "PS/2" (**) Option "CorePointer" (**) Configured Mouse: Core Pointer (**) Option "Device" "/dev/psaux" (**) Option "Emulate3Buttons" "true" (**) Configured Mouse: Emulate3Buttons, Emulate3Timeout: 50 (==) Configured Mouse: Buttons: 3 (II) XINPUT: Adding extended input device "Configured Mouse" (type: MOUSE) (II) Configured Mouse: ps2EnableDataReporting: succeeded Warning: font renderer for ".pcf" already registered at priority 0 Warning: font renderer for ".pcf.Z" already registered at priority 0 Warning: font renderer for ".pcf.gz" already registered at priority 0 Warning: font renderer for ".snf" already registered at priority 0 Warning: font renderer for ".snf.Z" already registered at priority 0 Warning: font renderer for ".snf.gz" already registered at priority 0 Warning: font renderer for ".bdf" already registered at priority 0 Warning: font renderer for ".bdf.Z" already registered at priority 0 Warning: font renderer for ".bdf.gz" already registered at priority 0 Warning: font renderer for ".pmf" already registered at priority 0 ============== XF86Config-4 : Section "Files" # FontPath "unix/:7100" # local font server # if the local font server has problems, we can fall back on these FontPath "/usr/X11R6/lib/X11/fonts/misc" FontPath "/usr/X11R6/lib/X11/fonts/cyrillic" FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/Type1" FontPath "/usr/X11R6/lib/X11/fonts/Speedo" FontPath "/usr/X11R6/lib/X11/fonts/100dpi" FontPath "/usr/X11R6/lib/X11/fonts/75dpi" EndSection Section "Module" Load "GLcore" Load "bitmap" # Load "dbe" # Load "ddc" Load "dri" Load "extmod" Load "freetype" Load "glx" Load "int10" # Load "pex5" # load "render" # load "randr" Load "record" Load "speedo" Load "type1" # Load "vbe" # Load "xie" EndSection Section "InputDevice" Identifier "Generic Keyboard" Driver "keyboard" Option "CoreKeyboard" Option "XkbRules" "xfree86" Option "XkbModel" "pc104" Option "XkbLayout" "us" EndSection Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "CorePointer" Option "Device" "/dev/psaux" Option "Protocol" "PS/2" Option "Emulate3Buttons" "true" # Option "ZAxisMapping" "4 5" EndSection Section "Device" Identifier "Generic Video Card" Driver "s3virge" #Chipset "virge mx+" # virge mx+, 86c325 375 385 365 368 #option "slow_edodram" # causes large decrease in performance #option "noaccel" # option "xvideo" "off" # option hwcursor "false" # option swcursor #"true" option "pci_burst" "on" option "fifo_aggressive" # option "fifo_moderate" # option "fifo_conservative" # option "mx_cr3a_fix" "true" #default on EndSection Section "Monitor" Identifier "Generic Monitor" HorizSync 31.5-49 VertRefresh 50-90 # Option "DPMS" EndSection Section "Screen" Identifier "Default Screen" Device "Generic Video Card" Monitor "Generic Monitor" DefaultDepth 24 SubSection "Display" Depth 8 Modes "800x600" "640x480" EndSubSection SubSection "Display" Depth 15 Modes "800x600" "640x480" EndSubSection SubSection "Display" Depth 16 Modes "800x600" "640x480" EndSubSection SubSection "Display" Depth 24 Modes "800x600" "640x480" EndSubSection EndSection Section "ServerLayout" Identifier "Default Layout" Screen "Default Screen" InputDevice "Generic Keyboard" InputDevice "Configured Mouse" # InputDevice "Generic Mouse" EndSection Section "DRI" Mode 0666 EndSection _______________________________________________ XFree86 mailing list XFree86@xxxxxxxxxxx http://XFree86.Org/mailman/listinfo/xfree86
