On Tue, 16 Sep 2003, Simon Ejsing wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > On Tuesday 16 September 2003 15:05, Kimmo Fredriksson wrote: > > Hi, > > > > I just installed Club3D (ATI) Radeon 9600 Pro, and the drivers for Linux > > from www.ati.com. The installation went fine, X starts OK, but I'm not > > getting 3D accelartion. > > > > XFree86.0.log says: > > > > (II) fglrx(0): Acceleration enabled > > (II) fglrx(0): Direct rendering disabled > > > > Accelaration enabled, but not direct rendering???? Why???? > > > > $ ldd /usr/X11R6/bin/glxgears > > libGL.so.1 => /usr/X11R6/lib/libGL.so.1 (0x40017000) > > libXext.so.6 => /usr/X11R6/lib/libXext.so.6 (0x40095000) > > libX11.so.6 => /usr/X11R6/lib/libX11.so.6 (0x400a3000) > > libpthread.so.0 => /lib/libpthread.so.0 (0x4019c000) > > libm.so.6 => /lib/libm.so.6 (0x401ee000) > > libc.so.6 => /lib/libc.so.6 (0x40210000) > > libdl.so.2 => /lib/libdl.so.2 (0x4034a000) > > /lib/ld-linux.so.2 => /lib/ld-linux.so.2 (0x40000000) > > > > $ ls -l /usr/X11R6/lib/libGL.so.1 > > lrwxrwxrwx 1 root root 27 Sep 16 14:00 > > /usr/X11R6/lib/libGL.so.1 -> /usr/X11R6/lib/libGL.so.1.2 > > > > and /usr/X11R6/lib/libGL.so.1.2 comes from ati... So I suppose the library > > should be correct. > > > > /sbin/lsmod says: > > > > fglrx 185224 0 > > > > Thanks to anyone who can help. > > > > (config and log are attached, if those help) > > > > kf > > Check what your dmesg says after running startx, it's most likely a mismatch > between kernel AGP achitecture and your DRM module. Ok, here goes: Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 439M agpgart: Unsupported Via chipset (device id: 3168), you might want to try agp_try_unsupported=1. agpgart: no supported devices found. [fglrx] Maximum main memory to use for locked dma buffers: 429 MBytes. [fglrx] module loaded - fglrx 3.2.5 [Aug 6 2003] on minor 0 Fire GL built-in AGP-support Based on agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 439M agpgart: Detected a Via P4X400 chipset in AGP v2 compatible mode at 00:00.0 agpgart: Detected Via P4X400 chipset agpgart: unable to determine aperture size. [fglrx:firegl_unlock] *ERROR* Process 1027 using kernel context 0 In the config I enabled fglrx's built-in agp support. There seems to be some error there, but I cannot decipher this... Any ideas what's wrong, and especially, how to fix it? Thanks a lot, kf > > - -- > Simon Ejsing, Systemudvikler > esoft ApS, http://www.esoft.dk > Kongensgade 66-68, DK-5000 Odense C. > Tlf: 70 222 466, Fax: 63 122 466 > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v1.2.3 (GNU/Linux) > > iD8DBQE/Zw8+0ZtqfKNZvaARAiI6AJ92y+drfhoL3dOSXfAGsBKeSq8PCwCfauJi > ARnAsgz8QSsYAGxgadltOgU= > =tGG7 > -----END PGP SIGNATURE----- > > _______________________________________________ XFree86 mailing list XFree86@xxxxxxxxxxx http://XFree86.Org/mailman/listinfo/xfree86
