Yes please. Sorry about Mandrake/Redhat mix up, didn't see original message :) Craig ----- Original Message ----- From: "Jeremy West" <jerwest1380@cs.com> To: <newbie@XFree86.Org> Sent: Tuesday, October 08, 2002 2:29 AM Subject: Re: ATI radeonb > Well, first of all I'm using redhat 8.0 not mandrake. Second of all > every installation wasn't guarenteed to be a success. I have had it > work under 7.1 sometimes, and 7.3 sometimes. I have only installed 8.0 > once so far on my box. Works great for me know. Also this is a 32 M > ddr card. Would you like the XFree Config file? > > Jeremy > > > On Mon, 2002-10-07 at 11:41, Craig Dyke wrote: > > I have had a number of problems with 3D and DRI under X using an ATI Radeon > > 32MB SDR. > > I would like to see the config file that Mandrake wrote for Jeremy below if > > it is truly > > working out of the box as it were :) > > > > Craig > > > > > > ----- Original Message ----- > > From: "Jeremy WEst" <jerwest1380@cs.com> > > To: <newbie@XFree86.Org> > > Sent: Tuesday, October 08, 2002 12:06 AM > > Subject: RE: ATI radeonb > > > > > > > Actually I have a Radeon 32 M and I get great 3d support from the Xfree > > > drivers. I didn't have to download any from the ATI site. 8.0 did a > > > great job of detecting it and enabling DRI. It's just the standard > > > radeon driver. I didn't try to use any of the more card specific > > > drivers. Try just the generic radeon driver. > > > > > > -----Original Message----- > > > From: newbie-admin@XFree86.Org [mailto:newbie-admin@XFree86.Org] On > > > Behalf Of Steve White > > > Sent: Monday, October 07, 2002 2:57 AM > > > To: newbie@XFree86.Org > > > Subject: Re: ATI radeonb > > > > > > The radeon is support in xfree 4.2.0 and above. It is only 2D support. > > > for 3D you have to go to the ATI website and download the driver. (I > > > had to do this with my 8500 - not sure about the radeon) They had > > > drivers compiled for both 4.1.0 and 4.2.0 on ATI's site for the 8500 - I > > > think it is the same driver (or very similar). They have a selection > > > routine that will get you what you need if it exists. Their drivers are > > > offered in rpm form. > > > > > > Steve W > > > > > > On Fri, 2002-10-04 at 18:32, Kurdty wrote: > > > > Hello, > > > > > > > > i have an ATI radeon 32 sdr. > > > > > > > > i' m using XFree4.1.0-16 > > > > > > > > this is a mach32 , mach64 ? > > > > i can't success in configuring it. Can you help me ? > > > > > > > > > > > > -- > > > > > > > > ._(¯`·._.·´¯`·-K u r d t Y-·´¯`·._.·´¯)_. > > > > > > > > See you at http://kurdty.free.fr/ > > > > > > > > ___________________________________________________________ > > > > Do You Yahoo!? -- Une adresse @yahoo.fr gratuite et en français ! > > > > Yahoo! Mail : http://fr.mail.yahoo.com > > > > _______________________________________________ > > > > > > > > Newbie@XFree86.Org > > > > *** To unsubscribe , or change message options, see: > > > > http://XFree86.Org/mailman/listinfo/newbie > > > > > > > > > _______________________________________________ > > > > > > Newbie@XFree86.Org > > > *** To unsubscribe , or change message options, see: > > > http://XFree86.Org/mailman/listinfo/newbie > > > > > > _______________________________________________ > > > > > > Newbie@XFree86.Org > > > *** To unsubscribe , or change message options, see: > > > http://XFree86.Org/mailman/listinfo/newbie > > > > > > _______________________________________________ > > > > Newbie@XFree86.Org > > *** To unsubscribe , or change message options, see: > > http://XFree86.Org/mailman/listinfo/newbie > > > _______________________________________________ > > Newbie@XFree86.Org > *** To unsubscribe , or change message options, see: > http://XFree86.Org/mailman/listinfo/newbie _______________________________________________ Newbie@XFree86.Org *** To unsubscribe , or change message options, see: http://XFree86.Org/mailman/listinfo/newbie
