>---- Mensaje original ---- >De : Klaus.Schmidinger@xxxxxxx >Fecha : 24/06/2014 - 18:23 (H) >Para : vdr@xxxxxxxxxxx >Asunto : Re: Diseqc question > >On 24.06.2014 18:17, Antti Hartikainen wrote: >> On Tue, Jun 24, 2014 at 06:02:31PM +0200, Jose Alberto Reguero wrote: >>> El Martes, 24 de junio de 2014 17:22:08 Jose Alberto Reguero escribió: >>>> El Martes, 24 de junio de 2014 16:47:57 Klaus Schmidinger escribió: >>>>> On 24.06.2014 16:32, Jose Alberto Reguero wrote: >>>>>> El Martes, 24 de junio de 2014 15:38:14 Klaus Schmidinger escribió: >>>>>>> On 24.06.2014 13:45, Jose Alberto Reguero wrote: >>>>>>>> El Martes, 24 de junio de 2014 13:25:15 Klaus Schmidinger escribió: >>>>>>>>> On 24.06.2014 12:58, Jose Alberto Reguero wrote: >>>>>>>>>> I have a double LNB. I have a stb without diseqc capabilities and I >>>>>>>>>> want to use it with the default diseqc port A, and I want to use >>>>>>>>>> vdr with the diseqc port B. It is that possible? >>>>>>>>> >>>>>>>>> Does this LNB point to two neighboring sat positions and have one >>>>>>>>> cable connector, or does it point to only one sat position and >>>>>>>>> have two cable connectors? >>>>>>>>> >>>>>>>>> Klaus >>>>>>>> >>>>>>>> It is only one sat position and two cable connectors. >>>>>>> >>>>>>> Then the next question is whether these two connectors are for the >>>>>>> (separate) horizontal and vertical band, or whether they both provide >>>>>>> all bands. In the latter case it should just work. >>>>>>> >>>>>>> Klaus >>>>>> >>>>>> Both provide all bands. They point to ASTRA 19.2E. >>>>>> >>>>>> I use this diseq.conf entries: >>>>>> >>>>>> S28.2E 11700 V 9750 t v W15 A W15 t >>>>>> S28.2E 99999 V 10600 t v W15 A W15 T >>>>>> S28.2E 11700 H 9750 t V W15 A W15 t >>>>>> S28.2E 99999 H 10600 t V W15 A W15 T >>>>>> >>>>>> S19.2E 11700 V 9750 t v W15 B W15 t >>>>>> S19.2E 99999 V 10600 t v W15 B W15 T >>>>>> S19.2E 11700 H 9750 t V W15 B W15 t >>>>>> S19.2E 99999 H 10600 t V W15 B W15 T >>>>>> >>>>>> (28.2E is just a fake entry) >>>>>> But when I tune a channel with vdr, the stb lost the signal. >>>>> >>>>> If both connectors provide all bands, you shouldn't need the 'A/B' >>>>> commands. >>>>> >>>>> Do you have a link to the specs of that LNB? >>>>> >>>>> Klaus >>>> >>>> It is a Opticum. I buy it in amazon. >>>> >>>> http://www.dipolnet.com/twin_lnb_opticum-orton_ltp-04h_premium_0_1db_A9842.h >>>> tm >>>> >>>> Jose Alberto >>>> >>>> >>> >>> I did another test, and if both channels are vertical there are not problems. >>> But if the stb is in a vertical channel, and vdr is in a horizontal channel, >>> the stb loose the signal. >>> >> >> Sound like broken LNB to me, if both tuners have their own cable coming from the outputs of LNB. > >I'd say so, too. > From the specs your configuration should work just fine. > >Klaus > No, the two cables go to a diseqc, and after the cable from the diseqc go to a amplifier with two outputs and each output go to a tuner. But the stb don't have diseqc capabilities. I am trying to configure the diseqc in the vdr part. It is posible? Jose Alberto _______________________________________________ vdr mailing list vdr@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
