I did that, i took my position with an gps, putet ther in lnb config, and afther that changing channels.conf form diferent satelites, but i did something wrong because i did not manage to get signal, until i setup my antena manualy again (form left right switches of motor). My idea was to use this patch and stored position from my motor!! --- On Tue, 6/9/09, Ales Jurik <ajurik@xxxxxxxx> wrote: > From: Ales Jurik <ajurik@xxxxxxxx> > Subject: Re: need help with GOTOX patch. > To: vdr@xxxxxxxxxxx > Cc: "lucian orasanu" <o_lucian@xxxxxxxxx> > Date: Tuesday, June 9, 2009, 1:31 PM > On Tuesday 09 of June 2009, lucian > orasanu wrote: > > Hy, > > > > I want to use this patch, but i dont know how. Only > this is necesary to > > move the motor: > > > > S5.0W 11700 V 9750 G v t > > S5.0W 99999 V 10600 G v T > > S5.0W 11700 H 9750 G V t > > S5.0W 99999 H 10600 G V T > > > > > > or should be like this: > > > > S1.0W 11700 V 9750 G v t [e0 31 6e 01(this bite > should be positon in rotor > > ?] S1.0W 99999 V 10600 G v T [e0 31 6e 01] > > S1.0W 11700 H 9750 G V t [e0 31 6e 01] > > S1.0W 99999 H 10600 G V T [e0 31 6e 01] > > > > with settings like this my motor wont move! > The first config should be ok. > > > > And in lnb setup menu at degres what should i put > there, my position? > Yes, your position. > > > > How this pach works?? > Patch is originaly written by Seppo Ingalsuo > (http://www.linuxtv.org/pipermail/vdr/2008-March/016164.html). > > The patch uses algo from vdr-rotor patch to calculate angle > to which motor > should move and send then the gotox diseqc command [e0 31 > 6e p1 p2] where p1 > and p2 is calculated angle. If you have dish with closer > beam be sure to have > position of satellites in sources.conf and channels.conf > written in right way > (for example satellites at 1.0W are at 0.83W and 0.75W > exactly) to be able to > receive also weaker transponders. > > The patch send this command only when satellite is > changing. You should also > use it for motor behind diseqc switch. The next example is > for 4-input diseqc > switch which has diseqc motor connected to input 4. Please > be sure that in > such way your dvb card will not be overloaded with output > current (you should > use motor which disconnect LNB when moving and card with > electronically > limited output current to prevent damages). > > S0.8W 11700 V 9750 t v > W15 [E0 10 38 FC] W150 G v t > S0.8W 99999 V 10600 t v W15 > [E0 10 38 FD] W150 G v T > S0.8W 11700 H 9750 t V > W15 [E0 10 38 FE] W150 G V t > S0.8W 99999 H 10600 t V W15 > [E0 10 38 FF] W150 G V T > > BR, > > Ales > > _______________________________________________ vdr mailing list vdr@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
