Jelle De Loecker schreef: > I've finally gotten VDR to work with my Technotrend S2-3200 card, but I > just can't seem to get this diseqc.conf file right! > > S19.2E 11700 V 9750 [E0 10 38 F0] > S19.2E 99999 V 10600 [E0 10 38 F1] > S19.2E 11700 H 9750 [E0 10 38 F2] > S19.2E 99999 H 10600 [E0 10 38 F3] > > S28.2E 11700 V 9750 [E0 10 38 F4] > S28.2E 99999 V 10600 [E0 10 38 F5] > S28.2E 11700 H 9750 [E0 10 38 F6] > S28.2E 99999 H 10600 [E0 10 38 F7] > > I have a diseqc 2.0 switch, but since the S2-3200 card only supports > Diseqc 1.2 I'm not really sure what to use! > It's a regular 4x1 switch > Apparantly a regular 4x1 switch doesn't need the "F0 - F1" bits at the end, and this will do. As I see it, the first hex-code is used for the option and the second hex-code is used for the position. (A/A-A/B-B/A-B/B) 22 Position A 23 Option A 26 Position B 27 Option B # port 1 option a position a # port 2 option a position b # port 3 option b position a # port 4 option b position b So in your setup I assume that you have ports and LNBs like this: 1 - S19.2E 2 - S28.2E 3 - S23.5E 4 - S13.0E This diseqc.conf should do the trick: # port 1 S19.2E 11700 V 9750 t v W15 [E0 10 23] W15 [E0 10 22] W15 t S19.2E 99999 V 10600 t v W15 [E0 10 23] W15 [E0 10 22] W15 T S19.2E 11700 H 9750 t V W15 [E0 10 23] W15 [E0 10 22] W15 t S19.2E 99999 H 10600 t V W15 [E0 10 23] W15 [E0 10 22] W15 T # port 2 S28.2E 11700 V 9750 t v W15 [E0 10 23] W15 [E0 10 26] W15 t S28.2E 99999 V 10600 t v W15 [E0 10 23] W15 [E0 10 26] W15 T S28.2E 11700 H 9750 t V W15 [E0 10 23] W15 [E0 10 26] W15 t S28.2E 99999 H 10600 t V W15 [E0 10 23] W15 [E0 10 26] W15 T # port 3 S23.5E 11700 V 9750 t v W15 [E0 10 27] W15 [E0 10 22] W15 t S23.5E 99999 V 10600 t v W15 [E0 10 27] W15 [E0 10 22] W15 T S23.5E 11700 H 9750 t V W15 [E0 10 27] W15 [E0 10 22] W15 t S23.5E 99999 H 10600 t V W15 [E0 10 27] W15 [E0 10 22] W15 T # port 4 S13.0E 11700 V 9750 t v W15 [E0 10 27] W15 [E0 10 26] W15 t S13.0E 99999 V 10600 t v W15 [E0 10 27] W15 [E0 10 26] W15 T S13.0E 11700 H 9750 t V W15 [E0 10 27] W15 [E0 10 26] W15 t S13.0E 99999 H 10600 t V W15 [E0 10 27] W15 [E0 10 26] W15 T Should you need to edit the first port I got this solution from the archive from these very own mailing lists, but it was very hard to find so I thought I'd post it again. It works like a charm: http://www.linuxtv.org/pipermail/vdr/2005-October/005517.html (thank you *Sami J. Mäkinen)* _______________________________________________ vdr mailing list vdr@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
