Hi folks. I recently lost the hard disk in my year-old VDR system and have had to rebuild from almost scratch. Everything is working except for the remote/keyboard. I've gone over things time and time again, but don't see anywhere that I've made a mistake. I've done quite a bit of searching (web and mailing list) and haven't found anything really helpful. I'm hoping someone here can point me in the right direction. Like I said in the subject, VDR will see the remote and keyboard long enough to create the remote.conf file, but when configuration is complete and VDR switches to normal 'show video' mode, both the remote and keyboard are ignored. Note that evtest output is normal, and that with IR debugging enabled, the remote keypresses show up in the log as expected. Installation details (note- I've tried to rebuild the system the same as it was prior to the crash): * Vanilla installation of Debian Sarge, 2.6.8 kernel recompiled from Debian-provided sources using the kernel config from the original (working) system. * In-kernel (non-CVS) DVB driver * Full featured Nexus card with the grey remote * VDR 1.3.20 compiled from source * Remote plugin version 0.3.3 * Loading hauppauge_grey.rc5 via av7110_loadkeys after inserting dvb-ttpci, prior to running VDR * Running VDR from the command line (not as a daemon) via ssh and screen. I don't see anything out of place in the syslog: Nov 29 22:13:31 localhost vdr[3539]: VDR version 1.3.20 started Nov 29 22:13:31 localhost vdr[3539]: loading plugin: ./PLUGINS/lib/libvdr- remote.so.1.3.20 Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/setup.conf Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/sources.conf Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/diseqc.conf Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/channels.conf Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/ca.conf Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/remote.conf Nov 29 22:13:31 localhost vdr[3539]: probing /dev/dvb/adapter0/frontend0 Nov 29 22:13:31 localhost vdr[3542]: tuner on device 1 thread started (pid=3542, tid=16386) Nov 29 22:13:31 localhost vdr[3543]: Section handler thread started (pid=3543, tid=32771) Nov 29 22:13:31 localhost vdr[3539]: probing /dev/dvb/adapter1/frontend0 Nov 29 22:13:31 localhost vdr[3539]: found 1 video device Nov 29 22:13:31 localhost vdr[3539]: initializing plugin: remote (0.3.3): Remote control Nov 29 22:13:31 localhost vdr[3539]: setting primary device to 1 Nov 29 22:13:31 localhost vdr[3539]: SVDRP listening on port 2001 Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/themes/classic- default.theme Nov 29 22:13:31 localhost vdr[3539]: starting plugin: remote Nov 29 22:13:31 localhost vdr[3539]: device /dev/input/event0: DVB on-card IR receiver Nov 29 22:13:31 localhost vdr[3539]: remote: using '/dev/input/event0' Nov 29 22:13:31 localhost vdr[3539]: remote-event0: autorepeat supported Nov 29 22:13:31 localhost vdr[3539]: remote-event0: exclusive access granted Nov 29 22:13:31 localhost vdr[3539]: loading /vdr_video/themes/classic- default.theme Nov 29 22:13:31 localhost vdr[3545]: KBD remote control thread started (pid=3545, tid=65541) Nov 29 22:13:31 localhost vdr[3539]: remote control remote-event0 - keys known Nov 29 22:13:31 localhost vdr[3539]: remote control KBD - keys known Nov 29 22:13:31 localhost vdr[3539]: switching to channel 177 Nov 29 22:13:31 localhost vdr[3539]: setting audio track to 1 Here are some keypresses from the log - Nov 29 22:28:08 localhost kernel: #########000007e5######### addr 31 data 0x25 (keycode 38) Nov 29 22:28:08 localhost kernel: #########00000fe0######### addr 31 data 0x20 (keycode 33) Nov 29 22:28:09 localhost kernel: #########000007e1######### addr 31 data 0x21 (keycode 34) Nov 29 22:28:09 localhost kernel: #########00000fd1######### addr 31 data 0x11 (keycode 18) Nov 29 22:28:10 localhost kernel: #########000007d0######### addr 31 data 0x10 (keycode 17) And the related entries from remote.conf remote-event0._Setup /proc/av7110_ir 00000000 31 remote-event0.Ok 0000000100010026 remote-event0.Up 0000000100010021 remote-event0.Down 0000000100010022 remote-event0.Left 0000000100010012 remote-event0.Right 0000000100010011 I'm really running into a wall here. What am I missing? Thanks, Benj -------------- next part -------------- An HTML attachment was scrubbed... URL: http://www.linuxtv.org/pipermail/vdr/attachments/20051130/70f14be5/attachment.htm
