Selon Christian Balzer <christian-balzer@xxxxxx>: > > ----- Original Message ----- > From: Christian Balzer > To: Klaus Schmidinger's VDR > Sent: Wednesday, November 02, 2005 11:56 AM > Subject: Re: Hollywood+ card working?? > > > > > michaelip@xxxxxxx schrieb: > Selon Christian Balzer <christian-balzer@xxxxxx>: > > Hi Michael, > > - the drivers are loaded > - i installed FFMPEG manually, but i thought that the c't vdr managed > the installation of all needed hollywood+ stuff correctly. Anyway, the > installation of ffmpeg didn't change anything > > When i try "mplayer -ao oss:/dev/em8300_ma-0 -vo dxr3 dvd://1" i can see > the DVD via the h+ card. So now i know that is not broken. But i cant't > imagine, what's wrong when i try to disply the vdr ... > > Christian > > > michaelip@xxxxxxx schrieb: > > Selon Lars Bl?ser <lars.blaeser@xxxxxxxxxxx>: > > > > Christian Balzer wrote: > > > second a dum question: where can I change the primary device? I found > various discussions about the primary device but i didn't find anything > about where to set this. In which configure file is this done??? > > > hi, > > to be certain that the h+ is working you could have a look at the init > parameters of the dxr3 drivers, there is a picture generator function > intergrated (can?t remember witch module, its to long ago) > > > > _______________________________________________ > vdr mailing list > vdr@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr > > > > > Christian, > > A Hollywood+ card needs some specific drivers to be loaded prior to use it ! > If your TV is flickering when loading the drivers, it seems that you have > some > drivers... Meanwhile, the TV screen should normally (often) became grren > for > a > while, before displaying the channel you're watching ! > > So that, could you please look at the following: > > 1. If you display loaded modules (bash command is lsmod), do you see the > em8300 > drivers ? > 2. Do you have FFMPEG installed correctly ? EM8300 drivers needs that ! > > EM8300 is the driver used to manage the Hollywood+ card. > > More informations about installing/using the DXR3 plugin is located at > http://www.linuxtv.org/vdrwiki/index.php/Dxr3-plugin > > PS: Before changing the setup.conf file for changing the primary device, > make > sure that vdr is not working ! > > > _______________________________________________ > vdr mailing list > vdr@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr > > > > > > > Ok. Your card and cable are working fine ! Nice ! > > So now let's try changing the setup.conf ! But bne sure that vdr is stopped > before changing the file as vdr saves the setup.conf file before leaving > (well, > that's what I noticed !)... > > By the way, before doing that ! Did you load the DXR3 plugin when starting > vdr ? > Because even if you use the wrong primary device for input, you should at > least > see the OSD on the TV ! > > Hope it helps. > > _______________________________________________ > vdr mailing list > vdr@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr > I tried to change settings in the setup.conf with a stopped vdr. But it > didn't work. :-( > Even the OSD is not displayed. I get nothing expect the flickering while > drivers are loaded. > Err, the dxr3 drivers are loaded by /etc/init.d/vdr start -dxr3 or not?? > When VDR is started these are last the ouput lines: > > av7110: found av7110-0 > adv717x.o Configuring for PAL > am8300_audio.o: Analof audio enabled > em8300: Microcode version 0x29 loaded > > Christian > > > > > -------------------------------------------------------------------------------- > > > _______________________________________________ > vdr mailing list > vdr@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr > Christian, I not use the same command than you for starting vdr ! To load plugins, I use -Ppluginname so, for the dxr3, it is -Pdxr3 ! You should also have a look at log files in case there is more messages ! Hope it helps... but not sure !
