here is my diseqc.conf # DiSEqC configuration for VDR # # Format: # # satellite slof polarization lof command... # # satellite: one of the 'S' codes defined in sources.conf # slof: switch frequency of LNB; the first entry with # an slof greater than the actual transponder # frequency will be used # polarization: V = vertical, H = horizontal # lof: the local oscillator frequency to subtract from # the actual transponder frequency # command: # t tone off # T tone on # v voltage low (13V) # V voltage high (18V) # A mini A # B mini B # Wnn wait nn milliseconds (nn may be any positive integer number) # [xx ...] hex code sequence (max. 6) # # The 'command...' part is optional. # # Examples: # Full DiSEqC sequence: S119W 11250 V 99999 t v W15 [E0 10 38 F0] W15 A W15 t S119W 99999 V 11250 t v W15 [E0 10 38 F1] W15 A W15 T S119W 11250 H 99999 t V W15 [E0 10 38 F2] W15 A W15 t S119W 99999 H 11250 t V W15 [E0 10 38 F3] W15 A W15 T S110W 11250 V 99999 t v W15 [E0 10 38 F4] W15 B W15 t S110W 99999 V 11250 t v W15 [E0 10 38 F5] W15 B W15 T S110W 11250 H 99999 t V W15 [E0 10 38 F6] W15 B W15 t S110W 99999 H 11250 t V W15 [E0 10 38 F7] W15 B W15 T and what happens when I cahnge channels softcam 0: setting new SID 118, source 84a6, transponder 33e06 softcam 0: logger stopped ecmcache: from cache: system Nagra (1800) id 0000 with ecm 24 softcam 0: try system Nagra (1800) id 0000 with ecm 24 (cached) (pri=-10) softcam 0: started logger sys=0x1800 id=0x0 system: using key N 101 00 B3E1DF3753758AB5 softcam 0: correct key found softcam 0: started logger sys=0x1800 id=0x0 softcam 0: check ProvidesCa: 1810 1801 1800 -> n=1 softcam 0: ignoring new SID 118, source 84a6, transponder 33e06 softcam 0: check ProvidesCa: 1810 1801 1800 -> n=1 softcam 0: setting new SID 506, source 844c, transponder 33e98 softcam 0: logger stopped ecmcache: from cache: system Nagra (1800) id 0000 with ecm 26 softcam 0: try system Nagra (1800) id 0000 with ecm 26 (cached) (pri=-10) softcam 0: started logger sys=0x1800 id=0x0 system: using key N 101 00 B3E1DF3753758AB5 softcam 0: correct key found softcam 0: started logger sys=0x1800 id=0x0 but when I change channels to this other sat, there is nothing but a blank screen. if I disconnect the switch and go direct then the system works perfect this happens with both vdr 1.3.22 and 1.3.23 any ideas -----Original Message----- From: vdr-bounces@xxxxxxxxxxx [mailto:vdr-bounces@xxxxxxxxxxx]On Behalf Of Oliver Endriss Sent: Monday, March 21, 2005 5:28 PM To: vdr@xxxxxxxxxxx Subject: Re: New Nexus FF Ver 2.3 cards Martin Spears wrote: > without the use of diseqc the card does work. I can recieve from several > sats as long as I do not use diseqc switching. If I were to go direct then > everything works perfect. Ok, let's assume that the DiSEqC code in the stv0299 driver is buggy. Try the attached patch. Does it work now? If not, try to load the stv0299 driver with parameter 'debug=1' and post the output when tuning. Please post your diseqc.conf file. Oliver -- -------------------------------------------------------- VDR Remote Plugin available at http://www.escape-edv.de/endriss/vdr/ -------------------------------------------------------- -- No virus found in this incoming message. Checked by AVG Anti-Virus. Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 3/18/2005 -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.308 / Virus Database: 266.8.0 - Release Date: 3/21/2005
