From: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
To better describe why the BBM is at offset 2000 describe the full
misinterpretation^Wmapping of the NAND memory that the i.MX hardware
implements.
Also adapt the comment to reality: A BBT is created automatically since
commit 2ad441bb7e78 ("mtd: nand-imx: Create BBT automatically when
necessary") which was included in v2020.03.0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
---
drivers/mtd/nand/nand_imx.c | 30 +++++++++++++++++++++---------
1 file changed, 21 insertions(+), 9 deletions(-)
diff --git a/drivers/mtd/nand/nand_imx.c b/drivers/mtd/nand/nand_imx.c
index 23b9c52e0f76..77655daa4efe 100644
--- a/drivers/mtd/nand/nand_imx.c
+++ b/drivers/mtd/nand/nand_imx.c
@@ -1139,20 +1139,32 @@ static int __init mxcnd_probe_dt(struct imx_nand_host *host)
* 512b data + 16b OOB +
* 512b data + 16b OOB
*
+ * So the mapping between original NAND addressing (as intended by the chip
+ * vendor) and interpretation when accessed via the i.MX NAND controller is as
+ * follows:
+ *
+ * original | i.MX
+ * ---------------------+---------------------
+ * data 0x0000 - 0x0200 | data 0x0000 - 0x0200
+ * data 0x0200 - 0x0210 | oob 0x0000 - 0x0010
+ * data 0x0210 - 0x0410 | data 0x0200 - 0x0400
+ * data 0x0410 - 0x0420 | oob 0x0010 - 0x0020
+ * data 0x0420 - 0x0620 | data 0x0400 - 0x0600
+ * data 0x0620 - 0x0630 | oob 0x0020 - 0x0030
+ * data 0x0630 - 0x0800 | data 0x0600 - 0x07d0
+ * oob 0x0000 - 0x0030 | data 0x07d0 - 0x0800
+ * oob 0x0030 - 0x0040 | oob 0x0030 - 0x0040
+ *
* This means that the factory provided bad block marker ends up
- * in the page data at offset 2000 instead of in the OOB data.
+ * in the page data at offset 2000 = 0x7d0 instead of in the OOB data.
*
- * To preserve the factory bad block information we take the following
- * strategy:
- *
- * - If the NAND driver detects that no flash BBT is present on 2k NAND
- * chips it will not create one because it would do so based on the wrong
- * BBM position
- * - This command is used to create a flash BBT then.
+ * If the NAND driver detects that no flash BBT is present on a 2k NAND
+ * chip it will create one automatically in the assumption that the NAND is
+ * pristine (that is completely erased with only vendor BBMs in the OOB) to
+ * preserve factory bad block information.
*
* From this point on we can forget about the BBMs and rely completely
* on the flash BBT.
- *
*/
static int checkbad(struct nand_chip *chip, loff_t ofs)
{
base-commit: f40319c8e157c90117d32aed1dae5549a723c63e
--
2.43.0
