We have a 2GB IMX8MP system using 32MB OPTEEE_SIZE, so expect to find Optee blob at 0xBE000000.
ATF compiled with:
make PLAT=imx8mp BL32_BASE=0xBE000000 IMX_BOOT_UART_BASE=0x30890000 SPD=opteed DEBUG=1 -j
Optee compiled with:
CFG_DDR_SIZE ?= UL(0x80000000)
CFG_UART_BASE ?= UART2_BASE
CFG_TZDRAM_START ?= 0xBE000000
undefine CFG_NS_ENTRY_ADDR
Barebox compiled with:
CONFIG_HAVE_OPTEE=y CONFIG_OPTEE_SIZE=0x02000000 # CONFIG_BOOTM_OPTEE is not set CONFIG_PBL_OPTEE=y CONFIG_FIRMWARE_IMX8MP_OPTEE=y
This produces the following on boot:
—————————————————><--------------
Uart initialized
Run level 3
Init power
Init DDR
Handover to ATF
imx8mp_load_and_start_image_via_tfa: Expect OPTEE at 0xbe000000
CH e2a7175151fe3e842116990e62c864334e1bb030ca146b749d8e6b0c02481357
IH e2a7175151fe3e842116990e62c864334e1bb030ca146b749d8e6b0c02481357
NOTICE: Do not release JR0 to NS as it can be used by HAB
NOTICE: BL31: v2.8(debug):lf-6.1.36-2.1.0-0-g1a3beeab6-dirty
NOTICE: BL31: Built : 13:14:09, Oct 18 2023
INFO: GICv3 with legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: Maximum SPI INTID supported: 191
INFO: BL31: Initializing runtime services
INFO: bl31_plat_get_next_image_ep_info: want image 0
INFO: bl31_plat_get_next_image_ep_info: bl32 PC is 0xbe000000
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing!
INFO: BL31: Initializing BL32
INFO: bl31_plat_get_next_image_ep_info: want image 0
INFO: bl31_plat_get_next_image_ep_info: bl32 PC is 0xbe000000
INFO: opteed_init: 176 - calling <opteed_synchronous_sp_entry>
INFO: opteed_synchronous_sp_entry: 79 - calling <opteed_enter_sp>
————————><————
I´m not sure why it asks for the same image twice and if this implies anything …
Hans
> 18. okt. 2023 kl. 11:06 skrev Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx>:
>
> Hello Hans,
>
> On 18.10.23 10:11, Hans Christian Lønstad wrote:
>> Just reaching out to ask whether anyone has successfully integrated Optee on the IMX8M(P) platform.
>> Our trials results in a crash when the ATF (NXP 2.8) does the handover to Optee (exit EL3).
>>
>> In ATF it appears that BL32 is expected to load at 0x56000000 on IMX8MP while Barebox actually loads
>> The Optee bin blob just below top of memory.
>> (Patching Barebox to the expected ATF BL32_BASE does not resolve the issue)
>>
>> Any help would be appreciated
>
> I am using OP-TEE in an i.MX8MN project successfully. The hardcoding of addresses
> is indeed unfortunate and it needs manual adjustment depending on the size
> of available RAM.
>
> The common configuration is to reserve secure memory at the end of DRAM as not
> to split the RAM in half. You should thus change the BL32 address used in TF-A
> in alignment with barebox CONFIG_OPTEE_SIZE, which is always relative to the end
> of RAM.
>
> Let me know how it goes.
>
> Cheers,
> Ahmad
>
>>
>> Hans Christian Lønstad
>>
>>
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
