According to the Kernel the DLL should only be enabled for clock
frequencies higher than 52MHz. Do likewise in barebox. Without this
we get
ERROR: rk3568-dwcmshc-sdhci fe2e0000.mmc@xxxxxxxxxxx: DLL lock timeout!
On a RK3588.
The patch is bigger than it actually needs to be. We are updating
register defines with it and move the "Disable cmd conflict check"
block further up to bring the code closer to the corresponding kernel
code.
Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
---
drivers/mci/rockchip-dwcmshc-sdhci.c | 52 ++++++++++++++++++++++------
1 file changed, 41 insertions(+), 11 deletions(-)
diff --git a/drivers/mci/rockchip-dwcmshc-sdhci.c b/drivers/mci/rockchip-dwcmshc-sdhci.c
index a935e921b1..c44f5731ca 100644
--- a/drivers/mci/rockchip-dwcmshc-sdhci.c
+++ b/drivers/mci/rockchip-dwcmshc-sdhci.c
@@ -25,21 +25,32 @@
#define DWCMSHC_EMMC_DLL_RXCLK 0x804
#define DWCMSHC_EMMC_DLL_TXCLK 0x808
#define DWCMSHC_EMMC_DLL_STRBIN 0x80c
+#define DECMSHC_EMMC_DLL_CMDOUT 0x810
#define DWCMSHC_EMMC_DLL_STATUS0 0x840
#define DWCMSHC_EMMC_DLL_START BIT(0)
+#define DWCMSHC_EMMC_DLL_LOCKED BIT(8)
+#define DWCMSHC_EMMC_DLL_TIMEOUT BIT(9)
#define DWCMSHC_EMMC_DLL_RXCLK_SRCSEL 29
#define DWCMSHC_EMMC_DLL_START_POINT 16
#define DWCMSHC_EMMC_DLL_INC 8
+#define DWCMSHC_EMMC_DLL_BYPASS BIT(24)
#define DWCMSHC_EMMC_DLL_DLYENA BIT(27)
-#define DLL_TXCLK_TAPNUM_DEFAULT 0x8
-#define DLL_STRBIN_TAPNUM_DEFAULT 0x8
+#define DLL_TXCLK_TAPNUM_DEFAULT 0x10
+#define DLL_TXCLK_TAPNUM_90_DEGREES 0xA
#define DLL_TXCLK_TAPNUM_FROM_SW BIT(24)
+#define DLL_STRBIN_TAPNUM_DEFAULT 0x8
#define DLL_STRBIN_TAPNUM_FROM_SW BIT(24)
-#define DWCMSHC_EMMC_DLL_LOCKED BIT(8)
-#define DWCMSHC_EMMC_DLL_TIMEOUT BIT(9)
+#define DLL_STRBIN_DELAY_NUM_SEL BIT(26)
+#define DLL_STRBIN_DELAY_NUM_OFFSET 16
+#define DLL_STRBIN_DELAY_NUM_DEFAULT 0x16
#define DLL_RXCLK_NO_INVERTER 1
#define DLL_RXCLK_INVERTER 0
-#define DWCMSHC_ENHANCED_STROBE BIT(8)
+#define DLL_CMDOUT_TAPNUM_90_DEGREES 0x8
+#define DLL_RXCLK_ORI_GATE BIT(31)
+#define DLL_CMDOUT_TAPNUM_FROM_SW BIT(24)
+#define DLL_CMDOUT_SRC_CLK_NEG BIT(28)
+#define DLL_CMDOUT_EN_SRC_CLK_NEG BIT(29)
+
#define DLL_LOCK_WO_TMOUT(x) \
((((x) & DWCMSHC_EMMC_DLL_LOCKED) == DWCMSHC_EMMC_DLL_LOCKED) && \
(((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0))
@@ -137,8 +148,32 @@ static void rk_sdhci_set_clock(struct rk_sdhci_host *host, unsigned int clock)
sdhci_set_clock(&host->sdhci, clock, clk_get_rate(host->clks[CLK_CORE].clk));
- if (clock <= 400000)
+ /* Disable cmd conflict check */
+ extra = sdhci_read32(&host->sdhci, DWCMSHC_HOST_CTRL3);
+ extra &= ~BIT(0);
+ sdhci_write32(&host->sdhci, DWCMSHC_HOST_CTRL3, extra);
+
+ if (clock <= 52000000) {
+ /*
+ * Disable DLL and reset both of sample and drive clock.
+ * The bypass bit and start bit need to be set if DLL is not locked.
+ */
+ sdhci_write32(&host->sdhci, DWCMSHC_EMMC_DLL_CTRL,
+ DWCMSHC_EMMC_DLL_BYPASS | DWCMSHC_EMMC_DLL_START);
+ sdhci_write32(&host->sdhci, DWCMSHC_EMMC_DLL_RXCLK, DLL_RXCLK_ORI_GATE);
+ sdhci_write32(&host->sdhci, DWCMSHC_EMMC_DLL_TXCLK, 0);
+ sdhci_write32(&host->sdhci, DECMSHC_EMMC_DLL_CMDOUT, 0);
+ /*
+ * Before switching to hs400es mode, the driver will enable
+ * enhanced strobe first. PHY needs to configure the parameters
+ * of enhanced strobe first.
+ */
+ extra = DWCMSHC_EMMC_DLL_DLYENA |
+ DLL_STRBIN_DELAY_NUM_SEL |
+ DLL_STRBIN_DELAY_NUM_DEFAULT << DLL_STRBIN_DELAY_NUM_OFFSET;
+ sdhci_write32(&host->sdhci, DWCMSHC_EMMC_DLL_STRBIN, extra);
return;
+ }
/* Reset DLL */
sdhci_write32(&host->sdhci, DWCMSHC_EMMC_DLL_CTRL, BIT(1));
@@ -158,11 +193,6 @@ static void rk_sdhci_set_clock(struct rk_sdhci_host *host, unsigned int clock)
return;
}
- /* Disable cmd conflict check */
- extra = sdhci_read32(&host->sdhci, DWCMSHC_HOST_CTRL3);
- extra &= ~BIT(0);
- sdhci_write32(&host->sdhci, DWCMSHC_HOST_CTRL3, extra);
-
extra = 0x1 << 16 | /* tune clock stop en */
0x2 << 17 | /* pre-change delay */
0x3 << 19; /* post-change delay */
--
2.39.2
