Hi Ahmad, On Wed, Dec 14, 2022 at 11:58:20AM +0100, Ahmad Fatoum wrote: > The Wifx L1 is a SAMA5D4 LoRaWAN gateway. It boots from NAND, but this > can be overridden by inserting a bootable SD-Card. > > This first port only provides second-stage SD-Card support. Nice. I browsed the individual patches - they all looked good. The DT file in patch 11 looks like a file that would be a good linux kernel candidate - but I guess this is for someone else to do. Full series are: Acked-by: Sam Ravnborg <sam@xxxxxxxxxxxx> I look forward to the day where the remaining three sama5d boards are all multi-board and DT-enabled. This patch-set brings us a step closer. Do you know if there is a way to read bootsource from an at91sam92XX CPU / ROMBOOT code? There as nothing mentioned in the datasheet I looked at. As I have fired up my at91sam9263 board for the Xmas holidays I may try to play around with it a bit, but for now I have only SD-card boot working. Sam It enables > use of UART, I2C/EEPROM, Ethernet and SD-Card. For NAND use on SAMA5D4, > an updated Linux driver was ported to barebox. > This will follow separately. > > Ahmad Fatoum (11): > ARM: at91: sama5: switch to nonnaked entry functions > ARM: at91: sama5d4: add entry point helpers > ARM: at91: sama5d4: enable for DT use > net: macb: match atmel,sama5d4-gem compatible > i2c: at91: extend for SAMA5D4 support > eeprom: at24: add 24mac402/602 support > driver: always ensure probe of RAM registered with mem_platform_driver > common: deep-probe: don't build without CONFIG_OFDEVICE > pinctrl: at91: make deep-probe compatible > ARM: at91: make bootsource code generic to all SAMA5 > ARM: at91: SAMA5D4: add Wifx L1 support > > arch/arm/boards/Makefile | 1 + > .../boards/microchip-ksz9477-evb/lowlevel.c | 6 +- > .../arm/boards/sama5d27-giantboard/lowlevel.c | 4 +- > arch/arm/boards/sama5d27-som1/lowlevel.c | 4 +- > arch/arm/boards/sama5d3_xplained/lowlevel.c | 6 +- > arch/arm/boards/sama5d4_wifx/Makefile | 4 + > arch/arm/boards/sama5d4_wifx/board.c | 38 ++ > arch/arm/boards/sama5d4_wifx/lowlevel.c | 18 + > arch/arm/dts/Makefile | 1 + > arch/arm/dts/at91-sama5d4_wifx_l1.dts | 358 ++++++++++++++++++ > arch/arm/dts/sama5d4.dtsi | 9 + > arch/arm/mach-at91/Kconfig | 11 + > arch/arm/mach-at91/Makefile | 3 +- > arch/arm/mach-at91/bootm-barebox.c | 3 +- > arch/arm/mach-at91/ddramc.c | 7 + > arch/arm/mach-at91/include/mach/barebox-arm.h | 22 +- > arch/arm/mach-at91/include/mach/cpu.h | 1 - > arch/arm/mach-at91/include/mach/ddramc.h | 1 + > .../mach-at91/include/mach/sama5_bootsource.h | 5 + > arch/arm/mach-at91/sama5_bootsource.c | 36 ++ > arch/arm/mach-at91/sama5d2.c | 15 - > arch/arm/mach-at91/setup.c | 3 - > common/Makefile | 2 +- > drivers/eeprom/at24.c | 2 + > drivers/i2c/busses/i2c-at91.c | 14 +- > drivers/net/macb.c | 1 + > drivers/pinctrl/pinctrl-at91.c | 20 +- > images/Makefile.at91 | 4 + > include/deep-probe.h | 7 + > include/driver.h | 13 +- > 30 files changed, 571 insertions(+), 48 deletions(-) > create mode 100644 arch/arm/boards/sama5d4_wifx/Makefile > create mode 100644 arch/arm/boards/sama5d4_wifx/board.c > create mode 100644 arch/arm/boards/sama5d4_wifx/lowlevel.c > create mode 100644 arch/arm/dts/at91-sama5d4_wifx_l1.dts > create mode 100644 arch/arm/dts/sama5d4.dtsi > create mode 100644 arch/arm/mach-at91/sama5_bootsource.c > > -- > 2.30.2 >
