Hi Johannes, On Tue, Jul 12, 2022 at 07:04:49AM +0200, Johannes Zink wrote: > This is a fixup for the documentation: fixed line breaks, whitespace changes > and typos as requested. > > Signed-off-by: Johannes Zink <j.zink@xxxxxxxxxxxxxx> > --- > Documentation/boards/imx/meerkat96.rst | 28 ++++++++++++++++++-------- > 1 file changed, 20 insertions(+), 8 deletions(-) Still many trailing whitespaces with this fixup. I fixed it up locally and applied, thanks Sascha > > diff --git a/Documentation/boards/imx/meerkat96.rst b/Documentation/boards/imx/meerkat96.rst > index 3cdb1beaf..3a51b9144 100644 > --- a/Documentation/boards/imx/meerkat96.rst > +++ b/Documentation/boards/imx/meerkat96.rst > @@ -1,28 +1,40 @@ > Meerkat 96 > ========== > > -The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz and 512 MB DRAM. For further details on the board's features check the manufacturers page at https://www.96boards.org/product/imx7-96 > +The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, > +featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz > +and 512 MB DRAM. For further details on the board's features check the > +manufacturers page at https://www.96boards.org/product/imx7-96 > > Serial console > -------------- > > -UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). If you use the UART-To-Serial-Converter provided with the board, you can just connect the Black jumper to B, the White to W and the Green to G. The UART uses 3.3V levels. > +UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen > +the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). > +If you use the UART-To-USB-Converter provided with the board, you can > +just connect the Black jumper to B, the White to W and the Green to G. > + > +The UART uses 3.3V levels. > > Building Barebox > ---------------- > > -To build Barebox for ZII i.MX7 based boards do the following: > - > -.. code-block:: sh > - > - make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper > +To build Barebox for the meerkat96 board do the following: > + > +.. code-block:: sh > + > + make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper > make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> imx_v7_defconfig > make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> > > Bringup > ------- > > -flash the resulting barebox-meerkat96.img to an sdcard at address 0. Make sure the pmic is set to power-on state by setting the dipswitch SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is the factory default). > +flash the resulting barebox-meerkat96.img to an sdcard at address 0. > + > +Make sure the pmic is set to power-on state by setting the dipswitch > +SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is > +the factory default). > > Schematics > ---------- > -- > 2.30.2 > > > -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
