On 22-07-04, Lucas Stach wrote:
> Am Montag, dem 04.07.2022 um 14:33 +0200 schrieb Marco Felsch:
> > The usptream TF-A was shifting around the base address from version to
> > version. But finally with upstream TF-A v2.7 it is correctly set to
> > 0x970000. This change was done since the final silicium has an SRAM size
> ^ silicon
> > of 576KB where as the pre-silicium had only 512KB.
> Please specify the tapeout version (A1) here.
>
> pre-silicon is a very different thing than a pre-release tapeout.
I will change that.
Regards,
Marco
> >
> > The upstream TF-A has adapt it in verion v2.5 so the BL31 blob is at the
> > end of the SRAM. Unfortunately they had (accidental) reverted back to
> > 0x960000 in v2.6. They noticed that and changed (again) back to 0x970000.
> > with v2.7.
> >
> > This commit also adapts the documentation for the i.MX8MP-EVK to
> > reference the upstream TF-A. The new warning should point out that we
> > strongly recommended to use versions from v2.7 onwards, due to the
> > version mess explained above.
> >
> > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
> > ---
> > Documentation/boards/imx/nxp-imx8mp-evk.rst | 11 +++++++----
> > arch/arm/mach-imx/include/mach/atf.h | 2 +-
> > 2 files changed, 8 insertions(+), 5 deletions(-)
> >
> > diff --git a/Documentation/boards/imx/nxp-imx8mp-evk.rst b/Documentation/boards/imx/nxp-imx8mp-evk.rst
> > index 366c1de500..1074992f2f 100644
> > --- a/Documentation/boards/imx/nxp-imx8mp-evk.rst
> > +++ b/Documentation/boards/imx/nxp-imx8mp-evk.rst
> > @@ -40,15 +40,18 @@ As a last step of this process those files need to be placed in
> > firmware/${f}; \
> > done
> >
> > -Get and Build the ARM Trusted firmware
> > ---------------------------------------
> > +Get and Build the Trusted Firmware A
> > +------------------------------------
> >
> > -Get ATF from https://source.codeaurora.org/external/imx/imx-atf, branch
> > -imx_5.4.3_2.0.0::
> > +Get TF-A from https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/ and
> > +checkout version v2.7::
> >
> > make PLAT=imx8mp bl31
> > cp build/imx8mp/release/bl31.bin ${barebox_srctree}/imx8mp-bl31.bin
> >
> > +.. warning:: It is important to use a version >= v2.7 else your system
> > + might not boot.
> > +
> > Build Barebox
> > -------------
> >
> > diff --git a/arch/arm/mach-imx/include/mach/atf.h b/arch/arm/mach-imx/include/mach/atf.h
> > index 09396f4646..bc400ddbad 100644
> > --- a/arch/arm/mach-imx/include/mach/atf.h
> > +++ b/arch/arm/mach-imx/include/mach/atf.h
> > @@ -10,7 +10,7 @@
> >
> > #define MX8MM_ATF_BL31_BASE_ADDR 0x00920000
> > #define MX8MN_ATF_BL31_BASE_ADDR 0x00960000
> > -#define MX8MP_ATF_BL31_BASE_ADDR 0x00960000
> > +#define MX8MP_ATF_BL31_BASE_ADDR 0x00970000
> > #define MX8MQ_ATF_BL31_BASE_ADDR 0x00910000
> > #define MX8M_ATF_BL33_BASE_ADDR 0x40200000
> > #define MX8MM_ATF_BL33_BASE_ADDR MX8M_ATF_BL33_BASE_ADDR
>
>
>
