Re: [PATCH v1 1/1] usb: net: Add support for the Realtek RTL8152B/RTL8153

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Oct 19, 2021 at 3:24 AM Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx> wrote:
> +
> +       buf = malloc(size);
> +       if (!buf)
> +               return -ENOMEM;

Barebox could use xmalloc here.  Ditto for other malloc/return ENOMEM patterns.


> +static int r8152_write_hwaddr(struct eth_device *edev, const unsigned char *adr)
> +{
> +       struct r8152 *tp = edev->priv;
> +       u8 tmp_addr[ETH_ALEN];
> +
> +       memcpy(tmp_addr, adr, ETH_ALEN);
> +
> +       debug("** %s (%d)\n", __func__, __LINE__);
> +
> +       ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_CONFIG);
> +       pla_ocp_write(tp, PLA_IDR, BYTE_EN_SIX_BYTES, 8, tmp_addr);

This writes 8 bytes from a buffer of 6 bytes.  It doesn't seem like
the temp buffer is even necessary.

> +/* Generic MII registers. */
> +#define MII_BMCR                0x00    /* Basic mode control register */
> +#define MII_BMSR                0x01    /* Basic mode status register  */
> +#define MII_PHYSID1             0x02    /* PHYS ID 1                   */
> +#define MII_PHYSID2             0x03    /* PHYS ID 2                   */
> +#define MII_ADVERTISE           0x04    /* Advertisement control reg   */
> +#define MII_LPA                 0x05    /* Link partner ability reg    */
> +#define MII_EXPANSION           0x06    /* Expansion register          */
> +#define MII_CTRL1000            0x09    /* 1000BASE-T control          */
> +#define MII_STAT1000            0x0a    /* 1000BASE-T status           */
> +#define MII_MMD_CTRL            0x0d    /* MMD Access Control Register */
> +#define MII_MMD_DATA            0x0e    /* MMD Access Data Register */
> +#define MII_ESTATUS             0x0f    /* Extended Status             */
> +#define MII_DCOUNTER            0x12    /* Disconnect counter          */
> +#define MII_FCSCOUNTER          0x13    /* False carrier counter       */
> +#define MII_NWAYTEST            0x14    /* N-way auto-neg test reg     */
> +#define MII_RERRCOUNTER         0x15    /* Receive error counter       */
> +#define MII_SREVISION           0x16    /* Silicon revision            */
> +#define MII_RESV1               0x17    /* Reserved...                 */
> +#define MII_LBRERROR            0x18    /* Lpback, rx, bypass error    */
> +#define MII_PHYADDR             0x19    /* PHY address                 */
> +#define MII_RESV2               0x1a    /* Reserved...                 */
> +#define MII_TPISTATUS           0x1b    /* TPI status for 10mbps       */
> +#define MII_NCONFIG             0x1c    /* Network interface config    */

These are defined already in linux/mii.h

> +
> +static u8 r8152b_pla_patch_a[] = {

Surely all these firmware images can be const too.

_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox



[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux