Hello Antony,
On 05.05.21 12:08, Antony Pavlov wrote:
> Tested on Digilent Arty FPGA board.
>
> Signed-off-by: Antony Pavlov <antonynpavlov@xxxxxxxxx>
> ---
> arch/riscv/boards/Makefile | 1 +
> arch/riscv/boards/litex-linux/Makefile | 3 +
> arch/riscv/boards/litex-linux/lowlevel.c | 20 +++++
> arch/riscv/dts/Makefile | 1 +
> arch/riscv/dts/litex-linux.dts | 96 ++++++++++++++++++++++++
> arch/riscv/mach-litex/Kconfig | 3 +
> images/Makefile.riscv | 4 +
> 7 files changed, 128 insertions(+)
>
> diff --git a/arch/riscv/boards/Makefile b/arch/riscv/boards/Makefile
> index 2ce9af41e0..d477cce362 100644
> --- a/arch/riscv/boards/Makefile
> +++ b/arch/riscv/boards/Makefile
> @@ -1,2 +1,3 @@
> # SPDX-License-Identifier: GPL-2.0
> obj-$(CONFIG_BOARD_ERIZO_GENERIC) += erizo/
> +obj-$(CONFIG_BOARD_LITEX_LINUX) += litex-linux/
> diff --git a/arch/riscv/boards/litex-linux/Makefile b/arch/riscv/boards/litex-linux/Makefile
> new file mode 100644
> index 0000000000..3d217ffe0b
> --- /dev/null
> +++ b/arch/riscv/boards/litex-linux/Makefile
> @@ -0,0 +1,3 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +pbl-y += lowlevel.o
> diff --git a/arch/riscv/boards/litex-linux/lowlevel.c b/arch/riscv/boards/litex-linux/lowlevel.c
> new file mode 100644
> index 0000000000..9ac1a3a42e
> --- /dev/null
> +++ b/arch/riscv/boards/litex-linux/lowlevel.c
> @@ -0,0 +1,20 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <common.h>
> +#include <asm/barebox-riscv.h>
> +#include <debug_ll.h>
> +
> +ENTRY_FUNCTION(start_litex_linux, a0, a1, a2)
> +{
> + extern char __dtb_z_litex_linux_start[];
> + extern void __barebox_nmon_entry(void);
I'd suggest <asm/nmon.h>, so this need not be repeated.
> +
> + if (IS_ENABLED(CONFIG_NMON))
> + __barebox_nmon_entry();
> + putc_ll('>');
> +
> + /* On POR, we are running from read-only memory here. */
> +
> + barebox_riscv_entry(0x40000000, SZ_256M,
> + __dtb_z_litex_linux_start + get_runtime_offset());
> +}
> diff --git a/arch/riscv/dts/Makefile b/arch/riscv/dts/Makefile
> index 4041c34e0c..dc5237b5bb 100644
> --- a/arch/riscv/dts/Makefile
> +++ b/arch/riscv/dts/Makefile
> @@ -5,5 +5,6 @@
> obj- += dummy.o
>
> pbl-$(CONFIG_BOARD_ERIZO_GENERIC) += erizo-generic.dtb.o
> +pbl-$(CONFIG_BOARD_LITEX_LINUX) += litex-linux.dtb.o
>
> clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts
> diff --git a/arch/riscv/dts/litex-linux.dts b/arch/riscv/dts/litex-linux.dts
> new file mode 100644
> index 0000000000..aa7e072305
> --- /dev/null
> +++ b/arch/riscv/dts/litex-linux.dts
> @@ -0,0 +1,96 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include "litex_soc_linux.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "LiteX VexRiscV-SoC-Linux";
> + compatible = "litex,vexriscv-soc-linux";
> +
> + aliases {
> + rom = &rom;
> + sram = &sram;
> + };
> +
> + /* ARTY board */
> + rom: rom@00000000 {
> + compatible = "mmio-sram";
> + reg = <0x00000000 0x00008000>;
> + read-only;
> + };
> +
> + sram: sram@20000000 {
> + compatible = "mmio-sram";
> + reg = <0x20000000 0x00004000>;
> + };
> +
> + main_ram: memory@40000000 {
> + device_type = "memory";
> + reg = <0x40000000 0x10000000>;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + spiflash: w25q128@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "winbond,w25q128", "jedec,spi-nor";
> + spi-max-frequency = <104000000>;
> + reg = <0>;
> + };
> +};
> +
> +/ {
Any reason, this can't be merge into / { } above?
> + ledsgpio: gpio@f0005000 {
> + compatible = "ti,74175";
> + reg = <0xf0005000 0x4>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + ld0 {
Nitpick: led-0 is what's required by the YAML schema.
> + label = "arty:green:ld0";
> + gpios = <&ledsgpio 0 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
That's redundant, isn't it?
> + };
> +
> + ld1 {
> + label = "arty:green:ld1";
> + gpios = <&ledsgpio 1 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + ld2 {
> + label = "arty:green:ld2";
> + gpios = <&ledsgpio 2 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + ld3 {
> + label = "arty:green:ld3";
> + gpios = <&ledsgpio 3 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> + };
> +
> + swgpio: gpio@f0007000 {
> + compatible = "ti,74125";
> + reg = <0xf0007000 0x4>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +};
> diff --git a/arch/riscv/mach-litex/Kconfig b/arch/riscv/mach-litex/Kconfig
> index 19d5927e44..3ff03b0e02 100644
> --- a/arch/riscv/mach-litex/Kconfig
> +++ b/arch/riscv/mach-litex/Kconfig
> @@ -3,6 +3,9 @@ if MACH_LITEX
> choice
> prompt "Board type"
>
> +config BOARD_LITEX_LINUX
> + bool "litex linux board"
> +
> endchoice
>
> endif
> diff --git a/images/Makefile.riscv b/images/Makefile.riscv
> index 463c6ce440..831858a54d 100644
> --- a/images/Makefile.riscv
> +++ b/images/Makefile.riscv
> @@ -10,3 +10,7 @@ $(obj)/%.nmon: $(obj)/%.img FORCE
> pblb-$(CONFIG_BOARD_ERIZO_GENERIC) += start_erizo_generic
> FILE_barebox-erizo-generic.img = start_erizo_generic.pblb
> image-$(CONFIG_BOARD_ERIZO_GENERIC) += barebox-erizo-generic.img barebox-erizo-generic.nmon
> +
> +pblb-$(CONFIG_BOARD_LITEX_LINUX) += start_litex_linux
> +FILE_barebox-litex-linux.img = start_litex_linux.pblb
> +image-$(CONFIG_BOARD_LITEX_LINUX) += barebox-litex-linux.img
barebox-litex-linux sounds quite strange for me as someone who hasn't
used LiteX.
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
