Re: [PATCH] mtd: nand: fix hardware ECC support in atmel_nand driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Feb 23, 2021 at 12:22:53PM +0100, Edoardo Scaglia wrote:
> When using a NAND memory with hardware ECC enabled on a Atmel SoC
> probing fails during barebox boot with following error:
> 
> nand_base: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
> nand_base: Micron MT29F4G08ABAEAWP
> nand_base: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
> WARNING: at drivers/mtd/nand/nand_base.c:5594/nand_scan_tail()!
> WARNING: No oob scheme defined for oobsize 224
> atmel_nand atmel_nand0: probe failed: No such device or address
> 
> The problem arises from commit b6bcd96de5a75bdc5d06a06f2efffc2d89e346ec
> which among several changes dropped CONFIG_NAND_ECC_HW symbol, however
> two references remained in atmel_nand driver causing the failure of NAND
> probing when hardware ECC is configured in a Atmel SoC.
> 
> Signed-off-by: Edoardo Scaglia <scaglia@xxxxxxxxxxxx>
> ---
>  drivers/mtd/nand/atmel_nand.c | 6 ++----
>  1 file changed, 2 insertions(+), 4 deletions(-)

Applied to master. Sorry for breaking it, it seems I only tested it with
software ecc.

Sascha

> 
> diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
> index db13f5b7e4..58d53b7a78 100644
> --- a/drivers/mtd/nand/atmel_nand.c
> +++ b/drivers/mtd/nand/atmel_nand.c
> @@ -1351,8 +1351,7 @@ static int __init atmel_nand_probe(struct device_d *dev)
>  	nand_chip->ecc.strength = pdata->ecc_strength ? : 1;
>  	nand_chip->ecc.size = 1 << pdata->ecc_size_shift ? : 512;
>  
> -	if (IS_ENABLED(CONFIG_NAND_ECC_HW) &&
> -	    pdata->ecc_mode == NAND_ECC_HW) {
> +	if (pdata->ecc_mode == NAND_ECC_HW) {
>  		nand_chip->ecc.mode = NAND_ECC_HW;
>  	}
>  
> @@ -1411,8 +1410,7 @@ static int __init atmel_nand_probe(struct device_d *dev)
>  
>  	host->ecc_code = xmalloc(mtd->oobsize);
>  
> -	if (IS_ENABLED(CONFIG_NAND_ECC_HW) &&
> -	    nand_chip->ecc.mode == NAND_ECC_HW) {
> +	if (nand_chip->ecc.mode == NAND_ECC_HW) {
>  		if (IS_ENABLED(CONFIG_NAND_ATMEL_PMECC) && pdata->has_pmecc)
>  			res = atmel_pmecc_nand_init_params(dev, host);
>  		else
> -- 
> 2.30.0
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/barebox
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox



[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux