There are dt-bindings for the setup of the clk configuration in the phy.
This patch adds support for these bindings in the driver.
Signed-off-by: Michael Grzeschik <m.grzeschik@xxxxxxxxxxxxxx>
---
drivers/net/phy/at803x.c | 181 +++++++++++++++++++++++++++++++++++++--
1 file changed, 175 insertions(+), 6 deletions(-)
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index b43cb0d23e..94349cbe0d 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -11,6 +11,9 @@
#include <init.h>
#include <linux/phy.h>
#include <linux/string.h>
+#include <linux/bitfield.h>
+#include <uapi/linux/mdio.h>
+#include <dt-bindings/net/qca-ar803x.h>
#define AT803X_INTR_ENABLE 0x12
#define AT803X_INTR_STATUS 0x13
@@ -27,6 +30,164 @@
#define AT803X_DEBUG_SYSTEM_MODE_CTRL 0x05
#define AT803X_DEBUG_RGMII_TX_CLK_DLY (1 << 8)
+/* AT803x supports either the XTAL input pad, an internal PLL or the
+ * DSP as clock reference for the clock output pad. The XTAL reference
+ * is only used for 25 MHz output, all other frequencies need the PLL.
+ * The DSP as a clock reference is used in synchronous ethernet
+ * applications.
+ *
+ * By default the PLL is only enabled if there is a link. Otherwise
+ * the PHY will go into low power state and disabled the PLL. You can
+ * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always
+ * enabled.
+ */
+#define AT803X_MMD7_CLK25M 0x8016
+#define AT803X_CLK_OUT_MASK GENMASK(4, 2)
+#define AT803X_CLK_OUT_25MHZ_XTAL 0
+#define AT803X_CLK_OUT_25MHZ_DSP 1
+#define AT803X_CLK_OUT_50MHZ_PLL 2
+#define AT803X_CLK_OUT_50MHZ_DSP 3
+#define AT803X_CLK_OUT_62_5MHZ_PLL 4
+#define AT803X_CLK_OUT_62_5MHZ_DSP 5
+#define AT803X_CLK_OUT_125MHZ_PLL 6
+#define AT803X_CLK_OUT_125MHZ_DSP 7
+
+/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask
+ * but doesn't support choosing between XTAL/PLL and DSP.
+ */
+#define AT8035_CLK_OUT_MASK GENMASK(4, 3)
+
+#define AT803X_CLK_OUT_STRENGTH_MASK GENMASK(8, 7)
+#define AT803X_CLK_OUT_STRENGTH_FULL 0
+#define AT803X_CLK_OUT_STRENGTH_HALF 1
+#define AT803X_CLK_OUT_STRENGTH_QUARTER 2
+
+#define ATH9331_PHY_ID 0x004dd041
+#define ATH8030_PHY_ID 0x004dd076
+#define ATH8031_PHY_ID 0x004dd074
+#define ATH8032_PHY_ID 0x004dd023
+#define ATH8035_PHY_ID 0x004dd072
+#define AT8030_PHY_ID_MASK 0xffffffef
+
+struct at803x_priv {
+ u16 clk_25m_reg;
+ u16 clk_25m_mask;
+};
+
+static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id)
+{
+ struct phy_driver *drv = to_phy_driver(phydev->dev.driver);
+
+ return (phydev->phy_id & drv->phy_id_mask)
+ == (phy_id & drv->phy_id_mask);
+}
+
+static int at803x_parse_dt(struct phy_device *phydev)
+{
+ const struct device_d *dev = &phydev->dev;
+ const struct device_node *node = dev->device_node;
+ struct at803x_priv *priv = phydev->priv;
+ unsigned int sel, mask;
+ u32 freq, strength;
+ int ret;
+
+ ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
+ if (!ret) {
+ mask = AT803X_CLK_OUT_MASK;
+ switch (freq) {
+ case 25000000:
+ sel = AT803X_CLK_OUT_25MHZ_XTAL;
+ break;
+ case 50000000:
+ sel = AT803X_CLK_OUT_50MHZ_PLL;
+ break;
+ case 62500000:
+ sel = AT803X_CLK_OUT_62_5MHZ_PLL;
+ break;
+ case 125000000:
+ sel = AT803X_CLK_OUT_125MHZ_PLL;
+ break;
+ default:
+ dev_err(dev, "invalid qca,clk-out-frequency\n");
+ return -EINVAL;
+ }
+
+ priv->clk_25m_reg |= FIELD_PREP(mask, sel);
+ priv->clk_25m_mask |= mask;
+
+ /* Fixup for the AR8030/AR8035. This chip has another mask and
+ * doesn't support the DSP reference. Eg. the lowest bit of the
+ * mask. The upper two bits select the same frequencies. Mask
+ * the lowest bit here.
+ *
+ * Warning:
+ * There was no datasheet for the AR8030 available so this is
+ * just a guess. But the AR8035 is listed as pin compatible
+ * to the AR8030 so there might be a good chance it works on
+ * the AR8030 too.
+ */
+ if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) ||
+ at803x_match_phy_id(phydev, ATH8035_PHY_ID)) {
+ priv->clk_25m_reg &= AT8035_CLK_OUT_MASK;
+ priv->clk_25m_mask &= AT8035_CLK_OUT_MASK;
+ }
+ }
+
+ ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
+ if (!ret) {
+ priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK;
+ switch (strength) {
+ case AR803X_STRENGTH_FULL:
+ priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL;
+ break;
+ case AR803X_STRENGTH_HALF:
+ priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF;
+ break;
+ case AR803X_STRENGTH_QUARTER:
+ priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER;
+ break;
+ default:
+ dev_err(dev, "invalid qca,clk-out-strength\n");
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int at803x_probe(struct phy_device *phydev)
+{
+ struct at803x_priv *priv;
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ return at803x_parse_dt(phydev);
+}
+
+static int at803x_clk_out_config(struct phy_device *phydev)
+{
+ struct at803x_priv *priv = phydev->priv;
+ int val;
+
+ if (!priv->clk_25m_mask)
+ return 0;
+
+ val = phy_read_mmd_indirect(phydev, AT803X_MMD7_CLK25M, MDIO_MMD_AN);
+ if (val < 0)
+ return val;
+
+ val &= ~priv->clk_25m_mask;
+ val |= priv->clk_25m_reg;
+
+ phy_write_mmd_indirect(phydev, AT803X_MMD7_CLK25M, MDIO_MMD_AN, val);
+
+ return 0;
+}
+
static int at803x_config_init(struct phy_device *phydev)
{
int ret;
@@ -46,33 +207,41 @@ static int at803x_config_init(struct phy_device *phydev)
return ret;
}
+ ret = at803x_clk_out_config(phydev);
+ if (ret < 0)
+ return ret;
+
return 0;
}
static struct phy_driver at803x_driver[] = {
{
/* ATHEROS 8035 */
- .phy_id = 0x004dd072,
- .phy_id_mask = 0xffffffef,
+ .phy_id = ATH8035_PHY_ID,
+ .phy_id_mask = AT8030_PHY_ID_MASK,
.drv.name = "Atheros 8035 ethernet",
+ .probe = at803x_probe,
.config_init = at803x_config_init,
.features = PHY_GBIT_FEATURES,
.config_aneg = &genphy_config_aneg,
.read_status = &genphy_read_status,
}, {
/* ATHEROS 8030 */
- .phy_id = 0x004dd076,
- .phy_id_mask = 0xffffffef,
+ .phy_id = ATH8030_PHY_ID,
+ .phy_id_mask = AT8030_PHY_ID_MASK,
.drv.name = "Atheros 8030 ethernet",
.config_init = at803x_config_init,
+ .probe = at803x_probe,
.features = PHY_GBIT_FEATURES,
.config_aneg = &genphy_config_aneg,
.read_status = &genphy_read_status,
}, {
/* ATHEROS 8031 */
- .phy_id = 0x004dd074,
- .phy_id_mask = 0xffffffef,
+ .phy_id = ATH8031_PHY_ID,
+ .phy_id_mask = AT8030_PHY_ID_MASK,
+ .drv.name = "Atheros 8030 ethernet",
.drv.name = "Atheros 8031 ethernet",
+ .probe = at803x_probe,
.config_init = at803x_config_init,
.features = PHY_GBIT_FEATURES,
.config_aneg = &genphy_config_aneg,
--
2.27.0
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
