From: Oleksij Rempel <linux@xxxxxxxxxxxxxxxx>
This DTS will be replaced by kernel version
Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
---
arch/arm/dts/imx6dl-alti6p.dts | 118 ++++++
arch/arm/dts/imx6dl-lanmcu.dts | 434 ++++++++++++++++++++
arch/arm/dts/imx6dl-plybas.dts | 186 +++++++++
arch/arm/dts/imx6dl-plym2m.dts | 132 ++++++
arch/arm/dts/imx6dl-prtmvt.dts | 164 ++++++++
arch/arm/dts/imx6dl-prtrvt.dts | 182 +++++++++
arch/arm/dts/imx6dl-prtvt7.dts | 472 +++++++++++++++++++++
arch/arm/dts/imx6dl-victgo.dts | 145 +++++++
arch/arm/dts/imx6dl-vicut1.dts | 51 +++
arch/arm/dts/imx6q-prti6q.dts | 554 +++++++++++++++++++++++++
arch/arm/dts/imx6q-prtwd2.dts | 188 +++++++++
arch/arm/dts/imx6q-vicut1.dts | 52 +++
arch/arm/dts/imx6qdl-prti6q.dtsi | 174 ++++++++
arch/arm/dts/imx6qdl-vicut1.dtsi | 208 ++++++++++
arch/arm/dts/imx6qp-prtwd3.dts | 675 +++++++++++++++++++++++++++++++
arch/arm/dts/imx6qp-vicutp.dts | 52 +++
arch/arm/dts/imx6ul-prti6g.dts | 81 ++++
arch/arm/dts/imx6ul-prti6g.dtsi | 330 +++++++++++++++
18 files changed, 4198 insertions(+)
create mode 100644 arch/arm/dts/imx6dl-alti6p.dts
create mode 100644 arch/arm/dts/imx6dl-lanmcu.dts
create mode 100644 arch/arm/dts/imx6dl-plybas.dts
create mode 100644 arch/arm/dts/imx6dl-plym2m.dts
create mode 100644 arch/arm/dts/imx6dl-prtmvt.dts
create mode 100644 arch/arm/dts/imx6dl-prtrvt.dts
create mode 100644 arch/arm/dts/imx6dl-prtvt7.dts
create mode 100644 arch/arm/dts/imx6dl-victgo.dts
create mode 100644 arch/arm/dts/imx6dl-vicut1.dts
create mode 100644 arch/arm/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/dts/imx6q-prtwd2.dts
create mode 100644 arch/arm/dts/imx6q-vicut1.dts
create mode 100644 arch/arm/dts/imx6qdl-prti6q.dtsi
create mode 100644 arch/arm/dts/imx6qdl-vicut1.dtsi
create mode 100644 arch/arm/dts/imx6qp-prtwd3.dts
create mode 100644 arch/arm/dts/imx6qp-vicutp.dts
create mode 100644 arch/arm/dts/imx6ul-prti6g.dts
create mode 100644 arch/arm/dts/imx6ul-prti6g.dtsi
diff --git a/arch/arm/dts/imx6dl-alti6p.dts b/arch/arm/dts/imx6dl-alti6p.dts
new file mode 100644
index 0000000000..8d53100bea
--- /dev/null
+++ b/arch/arm/dts/imx6dl-alti6p.dts
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Altesco I6P Board";
+ compatible = "alt,alti6p", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c1>;
+ status = "okay";
+};
+
+/* DDC */
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <50000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <50000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T configure DDC pins for HDMI! */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS3__I2C4_SDA 0x4001f8b1
+ MX6QDL_PAD_NANDF_WP_B__I2C4_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-lanmcu.dts b/arch/arm/dts/imx6dl-lanmcu.dts
new file mode 100644
index 0000000000..b05ed9c3ba
--- /dev/null
+++ b/arch/arm/dts/imx6dl-lanmcu.dts
@@ -0,0 +1,434 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2019 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "LANMCU";
+ compatible = "lan,lanmcu", "fsl,imx6dl";
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ memory {
+ reg = <0x10000000 0x10000000>;
+ };
+
+ reg_usb_otg_vbus: otg-vbus-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-OTG-VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 0>;
+ enable-active-high;
+ };
+
+ usdhc2_pwrseq: usdhc2_pwrseq {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wlan_npd>;
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+ };
+
+ display: display0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "bgr666";
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ panel {
+ compatible = "edt,etm0700g0bdh6";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ backlight_lcd: backlight_lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 5 7 9 12 15 20 27 35 47 62 81 107 142 188 248
+ 328 433 573 757 1000>;
+ default-brightness-level = <20>;
+ status = "okay";
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ debug0 {
+ label = "debug0";
+ gpios = <&gpio1 8 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ prti6q {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* HW revision detect */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_wlan_npd: wlan_npd {
+ fsl,pins = <
+ /* WL_REG_ON */
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x130b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
+ >;
+ };
+
+ pinctrl_ts_edt: ts1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ >;
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ linux,rs485-enabled-at-boot-time;
+ rts-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ linux,rs485-enabled-at-boot-time;
+ rts-gpios = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ touchscreen: edt_ft5406@38 {
+ compatible = "edt,edt-ft5406";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ts_edt>;
+ reg = <0x38>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+
+ touchscreen-size-x = <1792>;
+ touchscreen-size-y = <1024>;
+
+ touchscreen-fuzz-x = <0>;
+ touchscreen-fuzz-y = <0>;
+
+ /* Touch screen calibration */
+ threshold = <50>;
+ gain = <5>;
+ offset = <10>;
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ non-removable;
+ mmc-pwrseq = <&usdhc2_pwrseq>;
+ pm-ignore-notify;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+
+ partitions {
+ /*
+ * Map a partition at the last 64k of the area available for
+ * the second stage bootloader.
+ */
+ compatible = "fixed-partitions";
+ #size-cells = <1>;
+ #address-cells = <1>;
+
+ bootstate_backend: bootstate_backend@f0000 {
+ reg = <0xf0000 0x10000>;
+ label = "bootstate";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/imx6dl-plybas.dts b/arch/arm/dts/imx6dl-plybas.dts
new file mode 100644
index 0000000000..de0ba05e13
--- /dev/null
+++ b/arch/arm/dts/imx6dl-plybas.dts
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+ model = "Plymovent BAS board";
+ compatible = "ply,plybas", "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x10000000>;
+ };
+
+ backlight_lcd {
+ status = "disabled";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ button@20 {
+ label = "START";
+ linux,code = <31>;
+ gpios = <&gpio5 8 1>;
+ };
+ button@21 {
+ label = "CLEAN";
+ linux,code = <46>;
+ gpios = <&gpio5 9 1>;
+ };
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ debug0 {
+ label = "debug0";
+ gpios = <&gpio1 8 0>;
+ };
+
+ debug1 {
+ label = "debug1";
+ gpios = <&gpio1 9 0>;
+ };
+
+ light_tower1 {
+ label = "light_tower1";
+ gpios = <&gpio4 22 0>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ light_tower2 {
+ label = "light_tower2";
+ gpios = <&gpio4 23 0>;
+ };
+
+ light_tower3 {
+ label = "light_tower3";
+ gpios = <&gpio4 24 0>;
+ };
+
+ light_tower4 {
+ label = "light_tower4";
+ gpios = <&gpio4 25 0>;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ fsl,uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 20>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* CAN1_SR + CAN2_SR GPIO outputs */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
+
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 /* YACO_nIRQ */
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 /* YACO_BOOT0 */
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* YACO_nRESET */
+
+ MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x13070 /* BUZZER */
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x13070 /* ANA_OUT_SD */
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 /* ANA_OUT_ERR */
+
+ MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x13070 /* RELAY1 */
+ MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06 0x13070 /* RELAY2 */
+
+ MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0 /* IN1 */
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0 /* IN2 */
+ MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1b0b0 /* IN3 */
+ MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x1b0b0 /* IN4 */
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x1b0b0 /* IN5 */
+ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0 /* IN6 */
+ MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x1b0b0 /* IN7 */
+ MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b0 /* IN8 */
+ MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x1b0b0 /* IN9 */
+ MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b0 /* IN10 */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* IN11 */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 /* IN12 */
+
+ MX6QDL_PAD_DI0_PIN3__GPIO4_IO19 0x1a0b0 /* HMI */
+
+ /* HW revision detect */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 /* DEBUG0 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* DEBUG1 */
+
+ MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070 /* LED1 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070 /* LED2 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070 /* LED3 (lighttower) */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070 /* LED4 (lighttower) */
+ >;
+ };
+
+ /* RS485 UART */
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-plym2m.dts b/arch/arm/dts/imx6dl-plym2m.dts
new file mode 100644
index 0000000000..b66321fb46
--- /dev/null
+++ b/arch/arm/dts/imx6dl-plym2m.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Plymovent M2M board";
+ compatible = "ply,plym2m", "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x10000000>;
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ debug0 {
+ label = "debug0";
+ gpios = <&gpio1 8 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* CAN1_SR GPIO output */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* CAN1_TERM */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 /* TSC_BUSY */
+
+ /* HW revision detect */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_backlight_m2m: backlightm2mgrp {
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-prtmvt.dts b/arch/arm/dts/imx6dl-prtmvt.dts
new file mode 100644
index 0000000000..05fce7178f
--- /dev/null
+++ b/arch/arm/dts/imx6dl-prtmvt.dts
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+ model = "Protonic MVT board";
+ compatible = "prt,prtmvt", "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x20000000>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ button@20 {
+ label = "GPIO Key F1";
+ linux,code = <59>;
+ gpios = <&pca_gpio 0 GPIO_ACTIVE_LOW>;
+ };
+ button@21 {
+ label = "GPIO Key F2";
+ linux,code = <60>;
+ gpios = <&pca_gpio 1 GPIO_ACTIVE_LOW>;
+ };
+ button@22 {
+ label = "GPIO Key F3";
+ linux,code = <61>;
+ gpios = <&pca_gpio 2 GPIO_ACTIVE_LOW>;
+ };
+ button@23 {
+ label = "GPIO Key F4";
+ linux,code = <62>;
+ gpios = <&pca_gpio 3 GPIO_ACTIVE_LOW>;
+ };
+ button@24 {
+ label = "GPIO Key F5";
+ linux,code = <63>;
+ gpios = <&pca_gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ // Center
+ button@25 {
+ label = "GPIO Key CYCLE";
+ linux,code = <154>;
+ gpios = <&pca_gpio 5 GPIO_ACTIVE_LOW>;
+ };
+ button@26 {
+ label = "GPIO Key ESC";
+ linux,code = <1>;
+ gpios = <&pca_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+ button@27 {
+ label = "GPIO Key UP";
+ linux,code = <103>;
+ gpios = <&pca_gpio 7 GPIO_ACTIVE_LOW>;
+ };
+ button@28 {
+ label = "GPIO Key DOWN";
+ linux,code = <108>;
+ gpios = <&pca_gpio 8 GPIO_ACTIVE_LOW>;
+ };
+ button@29 {
+ label = "GPIO Key OK";
+ linux,code = <0x160>;
+ gpios = <&pca_gpio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ button@2a {
+ label = "GPIO Key F6";
+ linux,code = <64>;
+ gpios = <&pca_gpio 10 GPIO_ACTIVE_LOW>;
+ };
+ button@2b {
+ label = "GPIO Key F7";
+ linux,code = <65>;
+ gpios = <&pca_gpio 11 GPIO_ACTIVE_LOW>;
+ };
+ button@2c {
+ label = "GPIO Key F8";
+ linux,code = <66>;
+ gpios = <&pca_gpio 12 GPIO_ACTIVE_LOW>;
+ };
+ button@2d {
+ label = "GPIO Key F9";
+ linux,code = <67>;
+ gpios = <&pca_gpio 13 GPIO_ACTIVE_LOW>;
+ };
+ button@2e {
+ label = "GPIO Key F10";
+ linux,code = <68>;
+ gpios = <&pca_gpio 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&pwm2 {
+ status = "disabled";
+};
+
+&pcie {
+ status = "disabled";
+};
+
+&i2c1 {
+ pca_gpio: gpio@74 {
+ #gpio-cells = <2>;
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pca9539>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ gpio-controller;
+ };
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_pca9539: pca9539 {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-prtrvt.dts b/arch/arm/dts/imx6dl-prtrvt.dts
new file mode 100644
index 0000000000..802bd50ae6
--- /dev/null
+++ b/arch/arm/dts/imx6dl-prtrvt.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic RVT board";
+ compatible = "prt,prtrvt", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x10000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+
+ nfc@0 {
+ compatible = "ti,trf7970a";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nfc>;
+ spi-max-frequency = <2000000>;
+ interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
+ ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
+ <&gpio5 11 GPIO_ACTIVE_LOW>;
+ vin-supply = <®_3v3>;
+ vin-voltage-override = <3100000>;
+ autosuspend-delay = <30000>;
+ irq-status-read-quirk;
+ en2-rf-quirk;
+ t5t-rmb-extra-byte-quirk;
+ status = "okay";
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* nc */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_nfc: nfcgrp {
+ fsl,pins = <
+ /* NFC_ASK_OOK */
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x100b1
+ /* NFC_PWR_EN */
+ MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x100b1
+ /* NFC_EN2 */
+ MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x100b1
+ /* NFC_EN */
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
+ /* NFC_MOD */
+ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x100b1
+ /* NFC_IRQ */
+ MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x100b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-prtvt7.dts b/arch/arm/dts/imx6dl-prtvt7.dts
new file mode 100644
index 0000000000..c202e6786d
--- /dev/null
+++ b/arch/arm/dts/imx6dl-prtvt7.dts
@@ -0,0 +1,472 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic VT7";
+ compatible = "prt,prtvt7", "fsl,imx6dl";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000>;
+ brightness-levels = <0 20 81 248 1000>;
+ default-brightness-level = <20>;
+ num-interpolated-steps = <21>;
+ power-supply = <®_12v_bl>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ display {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_disp>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ esc {
+ label = "GPIO Key ESC";
+ linux,code = <KEY_ESC>;
+ gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+ };
+
+ up {
+ label = "GPIO Key UP";
+ linux,code = <KEY_UP>;
+ gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+ };
+
+ down {
+ label = "GPIO Key DOWN";
+ linux,code = <KEY_DOWN>;
+ gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+ };
+
+ enter {
+ label = "GPIO Key Enter";
+ linux,code = <KEY_ENTER>;
+ gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+ };
+
+ cycle {
+ label = "GPIO Key CYCLE";
+ linux,code = <KEY_CYCLEWINDOWS>;
+ gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+ };
+
+ f1 {
+ label = "GPIO Key F1";
+ linux,code = <KEY_F1>;
+ gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+ };
+
+ f2 {
+ label = "GPIO Key F2";
+ linux,code = <KEY_F2>;
+ gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+ };
+
+ f3 {
+ label = "GPIO Key F3";
+ linux,code = <KEY_F3>;
+ gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+ };
+
+ f4 {
+ label = "GPIO Key F4";
+ linux,code = <KEY_F4>;
+ gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+ };
+
+ f5 {
+ label = "GPIO Key F5";
+ linux,code = <KEY_F5>;
+ gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+ };
+
+ f6 {
+ label = "GPIO Key F6";
+ linux,code = <KEY_F6>;
+ gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+ };
+
+ f7 {
+ label = "GPIO Key F7";
+ linux,code = <KEY_F7>;
+ gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+ };
+
+ f8 {
+ label = "GPIO Key F8";
+ linux,code = <KEY_F8>;
+ gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+ };
+
+ f9 {
+ label = "GPIO Key F9";
+ linux,code = <KEY_F9>;
+ gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+ };
+
+ f10 {
+ label = "GPIO Key F10";
+ linux,code = <KEY_F10>;
+ gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ panel {
+ compatible = "innolux,g070y2t0ec";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+
+ reg_12v_bl: regulator-bl-12v {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_12v_bl>;
+ regulator-name = "12v-bl";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ tsc@0 {
+ compatible = "ti,tsc2046";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ spi-max-frequency = <100000>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+ pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ vcc-supply = <®_3v3>;
+
+ ti,vref-delay-usecs = /bits/ 16 <100>;
+
+ ti,x-min = /bits/ 16 <0>;
+ ti,x-max = /bits/ 16 <8000>;
+ ti,y-min = /bits/ 16 <0>;
+ ti,y-max = /bits/ 16 <4800>;
+ ti,x-plate-ohms = /bits/ 16 <800>;
+ ti,y-plate-ohms = /bits/ 16 <300>;
+ ti,pressure-max = /bits/ 16 <4095>;
+
+ ti,skip-samples = <2>;
+ ti,sample-period-msecs = <10>;
+ ti,report-period-msecs = <30>;
+
+ ti,filter-tolerance = <80>;
+ ti,touch-resistance-threshold = <3500>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&i2c1 {
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_codec>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+&i2c3 {
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ gpio_pca: gpio@74 {
+ compatible = "nxp,pca9539";
+ reg = <0x74>;
+ interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&ipu1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+ status = "okay";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&usbh1 {
+ status = "disabled";
+};
+
+&vpu {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_codec: codecgrp {
+ fsl,pins = <
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_ipu1_disp: ipudisp1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
+
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
+
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_12v_bl: 12blgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_tsc: tscgrp {
+
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-victgo.dts b/arch/arm/dts/imx6dl-victgo.dts
new file mode 100644
index 0000000000..55bc4c8d41
--- /dev/null
+++ b/arch/arm/dts/imx6dl-victgo.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2016 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-vicut1.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Kverneland Tellus GO";
+ compatible = "kvg,victgo", "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x20000000>;
+ };
+
+ rotary-encoder {
+ compatible = "rotary-encoder";
+ pinctrl-0 = <&pinctrl_rotary_ch>;
+ gpios = <&gpio2 3 0>, <&gpio2 4 0>;
+ linux,axis = <8>; /* REL_WHEEL */
+ rotary-encoder,steps-per-period = <4>;
+ rotary-encoder,relative-axis;
+ rotary-encoder,rollover;
+ wakeup-source;
+ };
+
+ rotary-button {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pinctrl_rotary_btn>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ button@0 {
+ label = "Rotary Key";
+ gpios = <&gpio2 05 1>;
+ linux,code = <KEY_ENTER>;
+ gpio-key,wakeup;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&uart2 {
+ status = "disabled";
+};
+
+&i2c1 {
+ ht16k33: ht16k33@70 {
+ compatible = "holtek,ht16k33";
+ pinctrl-0 = <&pinctrl_ht16k33>;
+ reg = <0x70>;
+ refresh-rate-hz = <20>;
+ debounce-delay-ms = <50>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+ keypad,num-rows = <12>;
+ keypad,num-columns = <3>;
+ linux,keymap = <
+ MATRIX_KEY(2, 0, KEY_F6)
+ MATRIX_KEY(3, 0, KEY_F8)
+ MATRIX_KEY(4, 0, KEY_F10)
+ MATRIX_KEY(5, 0, KEY_F4)
+ MATRIX_KEY(6, 0, KEY_F2)
+ MATRIX_KEY(2, 1, KEY_F5)
+ MATRIX_KEY(3, 1, KEY_F7)
+ MATRIX_KEY(4, 1, KEY_F9)
+ MATRIX_KEY(5, 1, KEY_F3)
+ MATRIX_KEY(6, 1, KEY_F1)
+ >;
+ };
+};
+
+&pwm2 {
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
+ MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_rotary_ch: rotarygrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 /* ROTARY_A */
+ MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 /* ROTARY_B */
+ >;
+ };
+
+ pinctrl_rotary_btn: rotarygrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b0 /* ROTARY_BTN */
+ >;
+ };
+
+ pinctrl_ht16k33: ht16k33grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 /* IRQ */
+ >;
+ };
+
+ pinctrl_tsc2046e: tsc2046egrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6dl-vicut1.dts b/arch/arm/dts/imx6dl-vicut1.dts
new file mode 100644
index 0000000000..725acbefc5
--- /dev/null
+++ b/arch/arm/dts/imx6dl-vicut1.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6dl.dtsi>
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+ model = "Kverneland UT1 Board";
+ compatible = "kvg,vicut1", "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6q-prti6q.dts b/arch/arm/dts/imx6q-prti6q.dts
new file mode 100644
index 0000000000..f0469d5f62
--- /dev/null
+++ b/arch/arm/dts/imx6q-prti6q.dts
@@ -0,0 +1,554 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6q.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic PRTI6Q board";
+ compatible = "prt,prti6q", "fsl,imx6q";
+
+ chosen {
+ environment {
+ compatible = "barebox,environment";
+ device-path = &ecspi1, "partname:env";
+ };
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0xf0000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <16>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ can3_25m_osc: can3-25m-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-debug1 {
+ function = LED_FUNCTION_SD;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_wifi: regulator-wifi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ enable-active-high;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "regulator-WL12xx";
+ startup-delay-us = <70000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux_ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux_pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x0 0x100000>;
+ };
+
+ partition@100000 {
+ label = "env";
+ reg = <0x100000 0x10000>;
+ };
+
+ partition@110000 {
+ label = "spare";
+ reg = <0x110000 0x2f0000>;
+ };
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can3>;
+ clocks = <&can3_25m_osc>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <5000000>;
+ };
+
+ adc@1 {
+ compatible = "ti,adc128s052";
+ reg = <1>;
+ spi-max-frequency = <2000000>;
+ vref-supply = <®_3v3>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@0 {
+ reg = <0>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ sgtl5000: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+/* DDC */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* can2_l */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can2_h */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "ac97-slave";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ vmmc-supply = <®_wifi>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+
+ wifi {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi>;
+ interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = "38400000";
+ tcxo-clock-frequency = "19200000";
+ };
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
+ >;
+ };
+
+ pinctrl_can3: can3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ /* ADC128S022 CS */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T
+ * configure DDC pins for HDMI!
+ */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ /* DDC */
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg_id: usbotgidgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi: wifigrp {
+ fsl,pins = <
+ /* WL12xx IRQ */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6q-prtwd2.dts b/arch/arm/dts/imx6q-prtwd2.dts
new file mode 100644
index 0000000000..8572917865
--- /dev/null
+++ b/arch/arm/dts/imx6q-prtwd2.dts
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2018 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6q.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Protonic WD2 board";
+ compatible = "prt,prtwd2", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+ };
+
+ /* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
+ i2c@4 {
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ i2c-gpio,delay-us = <20>; /* ~10 kHz */
+ i2c-gpio,scl-output-only;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&can1 {
+ pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ pause;
+ full-duplex;
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* V in */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* I charge */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* V bus */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ /* nc */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ no-1-8-v;
+ non-removable;
+ mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+ pm-ignore-notify;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_eth_chg>;
+
+ pinctrl_can1phy: can1phy {
+ fsl,pins = <
+ /* CAN1_SR */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP4 */
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x130b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ /* nINTRP */
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1f8b0
+ MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f8b0
+ >;
+ };
+
+ pinctrl_usb_eth_chg: usbethchggrp {
+ fsl,pins = <
+ /* USB charging control */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ /* WL_REG_ON */
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6q-vicut1.dts b/arch/arm/dts/imx6q-vicut1.dts
new file mode 100644
index 0000000000..9f60ed1ac2
--- /dev/null
+++ b/arch/arm/dts/imx6q-vicut1.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6q.dtsi>
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+ model = "Kverneland UT1Q Board";
+ compatible = "kvg,vicut1q", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0xf0000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ /* phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; */
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-prti6q.dtsi b/arch/arm/dts/imx6qdl-prti6q.dtsi
new file mode 100644
index 0000000000..ed526d185f
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-prti6q.dtsi
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: regulator-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "h1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-vicut1.dtsi b/arch/arm/dts/imx6qdl-vicut1.dtsi
new file mode 100644
index 0000000000..dc18614f89
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-vicut1.dtsi
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ gpio_key_pwr: gpio_keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ power {
+ label = "GPIO Key Power";
+ gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ debug0 {
+ label = "debug0";
+ gpios = <&gpio1 8 0>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ debug1 {
+ label = "debug1";
+ gpios = <&gpio1 9 0>;
+ linux,default-trigger = "mmc";
+ };
+
+ power_led {
+ label = "power_led";
+ gpios = <&gpio2 24 0>;
+ default-state = "on";
+ };
+
+ isb_led {
+ label = "isb_led";
+ gpios = <&gpio4 31 0>;
+ default-state = "off";
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&i2c3 {
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&iomuxc {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ /* CAN1_SR + CAN2_SR GPIO outputs */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
+ /* CAN1_TERM */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ /* ITU656_nRESET */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ /* CAM1_MIRROR */
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
+ /* CAM2_MIRROR */
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
+ /* CAM_nDETECT */
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ /* nON_SWITCH */
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
+ /* ISB_IN1 */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
+ /* ISB_nIN2 */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
+ /* WARN_LIGHT */
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
+ /* ON2_FB */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
+ /* YACO_nIRQ */
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
+ /* YACO_BOOT0 */
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
+ /* YACO_nRESET */
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
+ /* FORCE_ON1 */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
+ /* AUDIO_nRESET */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
+ /* ITU656_nPDN */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+
+ /* HW revision detect */
+ /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ /* REV_ID1 = PWM output LED_PWM (SION) */
+ /* defined in &pinctrl_pwm3 */
+ /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ /* REV_ID4 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+
+ /* New in HW revision 1 */
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 /* ON1_FB */
+ MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 /* DIP1_FB */
+
+ /* New in UTC (UT1 HW revision 1) and TGO */
+ /* WHEEL */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x100b0
+ /* RADAR */
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x100b0
+ /* PTO */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x100b0
+ /* CPU_ON1_CTRL */
+ MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0
+ /* CPU_ON2_CTRL */
+ MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x1b0b0
+ /* CPU_HITCH_IN_OUT */
+ MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x100b0
+ /* CPU_LIGHT_ON */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x100b0
+ /* CPU_CONTACT_IN */
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x100b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ /* YaCO AUX Uart */
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ /* YaCO Touchscreen UART */
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ /* DEBUG0A */
+ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
+ /* DEBUG1A */
+ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
+ /* DEBUG0 */
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ /* DEBUG1 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ /* POWER_LED */
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
+ /* ISB_LED */
+ MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ /* ISB LED (not in TGO or UTC version 1+) */
+ MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ /* REV_ID1 = PWM output LED_PWM (SION for ID) */
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x4001b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qp-prtwd3.dts b/arch/arm/dts/imx6qp-prtwd3.dts
new file mode 100644
index 0000000000..0ef0bae036
--- /dev/null
+++ b/arch/arm/dts/imx6qp-prtwd3.dts
@@ -0,0 +1,675 @@
+/*
+ * Copyright (c) 2018 Protonic Holland
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include <arm/imx6qp.dtsi>
+#include "imx6qdl-prti6q.dtsi"
+
+/ {
+ model = "Protonic WD3 board";
+ compatible = "prt,prtwd3", "fsl,imx6qp";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ aliases {
+ mdio-gpio0 = &mdio0;
+ };
+
+ usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
+ };
+
+ clk20m_can: fdcan_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <20000000>;
+ };
+
+ clk25m_switch: switch_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ clk25m_phy3: phy3_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ clk50m_phy: phy_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mdio0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&gpio5 6 GPIO_ACTIVE_HIGH
+ &gpio5 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ display_panel0 {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ display_panel0_in: endpoint {
+ remote-endpoint = <&serializer0_out>;
+ };
+ };
+ };
+
+ display_panel1 {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_panel1>;
+
+ port {
+ display_panel1_in: endpoint {
+ remote-endpoint = <&serializer1_out>;
+ };
+ };
+ };
+
+ backlight_lcd: backlight_lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192 255>;
+ default-brightness-level = <15>;
+ power-supply = <®_3v3>;
+ };
+
+ backlight_panel1: backlight_panel1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 5000000>;
+ brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192 255>;
+ default-brightness-level = <0>;
+ power-supply = <®_3v3>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ status = "okay";
+
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET_REF>,
+ <&clks IMX6QDL_CLK_ENET_REF>;
+ clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+ assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF>;
+ assigned-clock-rates = <125000000>;
+
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+
+ mdio1: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Microchip KSZ9031 */
+ rgmii_phy: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_EDGE_FALLING>;
+
+ /* FIXME: tx/rx clk skew are currently set by imx
+ * platform driver. Write own walues here to not depend
+ * fixup of horror.
+ */
+
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ /* reset assert time is provided by documentation */
+ reset-assert-us = <10000>;
+ /* documented reset deassert time (100us) is not enough
+ * use test value of 300us.
+ */
+ reset-deassert-us = <1000>;
+
+ clocks = <&clk25m_phy3>;
+ };
+ };
+};
+
+&ecspi2 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+ sja1105_switch: sja1105@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "nxp,sja1105q";
+ spi-max-frequency = <4000000>;
+ spi-cpha;
+ spi-rx-delay-us = <1>;
+ spi-tx-delay-us = <1>;
+
+ reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
+
+ clocks = <&clk25m_switch>;
+ #clock-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "usb";
+ phy-handle = <&usbeth_phy>;
+ phy-mode = "rmii";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "t1slave";
+ phy-handle = <&tja1102_phy1>;
+ phy-mode = "rmii";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "t1master";
+ phy-handle = <&tja1102_phy0>;
+ phy-mode = "rmii";
+
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "rj45";
+ phy-handle = <&rgmii_phy>;
+ phy-mode = "rgmii-id";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "cpu";
+ ethernet = <&fec>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+&mdio0 {
+ usbeth_phy: ethernet-phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x3>;
+
+ interrupts-extended = <&gpio5 12 IRQ_TYPE_LEVEL_LOW>;
+ micrel,led-mode = <0>;
+
+ reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <500>;
+ reset-deassert-us = <1000>;
+
+ /* FIXME: the clock is provided by switch and we should know
+ * and we should request it only after switch have done clock
+ * configuration. Since it is currently not implemented,
+ * use fixed clock.
+ * WARNING: Using fixed clocks in this case is potential source
+ * for evil bugs. Switch may reconfigure, stop or change clk
+ * freq without letting PHY to know about it.
+ */
+ clocks = <&clk50m_phy>;
+ clock-names = "rmii-ref";
+ };
+
+ tja1102_phy0: ethernet-phy@4 {
+ compatible = "ethernet-phy-id0180.dc80";
+ reg = <0x4>;
+
+ interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ /* reset detection time is 20 usec. */
+ reset-assert-us = <20>;
+ /* reset to standby 2 msec. */
+ reset-deassert-us = <2000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tja1102_phy1: ethernet-phy@5 {
+ reg = <0x5>;
+
+ interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+ can3: can@0 {
+ compatible = "microchip,mcp2518fd";
+ spi-max-frequency = <5000000>;
+ reg = <0>;
+ clocks = <&clk20m_can>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <25 0x2>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ serializer0: ds90ub927@c {
+ compatible = "ti,ds90ub927";
+ reg = <0x0c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ serializer0_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ /* port@1 {
+ reg = <1>;
+ serializer0_audio_in: endpoint {
+ remote-endpoint = <&audio_i2s0_out>;
+ };
+ }; */
+ port@2 {
+ reg = <2>;
+ serializer0_out: endpoint {
+ remote-endpoint = <&display_panel0_in>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ serializer1: ds90ub927@c {
+ compatible = "ti,ds90ub927";
+ reg = <0x0c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ serializer1_in: endpoint {
+ remote-endpoint = <&lvds1_out>;
+ };
+ };
+ port@2 {
+ reg = <2>;
+ serializer1_out: endpoint {
+ remote-endpoint = <&display_panel1_in>;
+ };
+ };
+ };
+
+ camdeser: ds90ub954@30 {
+ compatible = "ti,ds90ub954";
+ reg = <0x30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ camdeser_fpd_link_in: endpoint {
+ };
+ };
+ port@1 {
+ reg = <1>;
+ camdeser_mipi_out: endpoint {
+ remote-endpoint = <&mipi_csi_in>;
+ };
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v; /* force 3.3V VIO */
+ non-removable;
+ mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+ pm-ignore-notify;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <1>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&serializer0_in>;
+ };
+ };
+ };
+
+ lvds-channel@1 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds1_out: endpoint {
+ remote-endpoint = <&serializer1_in>;
+ };
+ };
+ };
+};
+
+&mipi_csi {
+ status = "okay";
+ port@0 {
+ reg = <0>;
+
+ mipi_csi_in: endpoint {
+ remote-endpoint = <&camdeser_mipi_out>;
+ };
+ };
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ /* Empty, to disable parallel camera from PRTI6Q */
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Configure clock provider for RGMII ref clock */
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0b0
+ /* Configure clock consumer for RGMII ref clock */
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+
+ /* SJA1105Q switch reset */
+ MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x10030
+
+ /* phy3/rgmii_phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x10030
+ /* phy3/rgmii_phy int */
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x40010000
+ >;
+ };
+
+ pinctrl_mdio0: mdio0grp {
+ fsl,pins = <
+ /* phy0/usbeth_phy reset */
+ MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x10030
+ /* phy0/usbeth_phy int */
+ MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
+
+ /* phy12/tja1102_phy0 reset */
+ MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x10030
+ /* phy12/tja1102_phy0 int */
+ MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x100b1
+ /* phy12/tja1102_phy0 enable. Set 100K pull-up */
+ MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1f030
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ /* CAN1_SR + CAN2_SR GPIO outputs */
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
+ /* CAN1_TERM (not used on WD3) */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+
+ /* HW revision detect */
+ /* REV_ID0 */
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+ /* REV_ID1 */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* REV_ID2 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* REV_ID3 */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ /* REV_ID4 */
+ MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+
+ /* USB charging control */
+ /* CHG Control */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
+ /* RID0 */
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
+ /* RID1 */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
+ /* RID2 */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
+
+ /* Power VSEL and TG */
+ /* VSEL */
+ MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x1b0b0
+ /* TG */
+ MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
+
+ /* Display panel 0 GPIO */
+ /* L/R */
+ MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b0
+ /* TS_nINT */
+ MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0
+ /* EN */
+ MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30 0x1b0b0
+ /* LVDS0_nINT */
+ MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x1b0b0
+ /* LVDS0_PD */
+ MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01 0x1b0b0
+
+ /* Display panel 1 GPIO */
+ /* L/R */
+ MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
+ /* TS_nINT */
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
+ /* EN */
+ MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x1b0b0
+ /* LVDS1_nINT */
+ MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x1b0b0
+ /* LVDS1_PD */
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b0
+
+ /* Camera */
+ /* CAM_GPIO0 */
+ MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31 0x1b0b0
+ /* CAM_nINT */
+ MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x1b0b0
+ /* CAM_GPIO1 */
+ MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x1b0b0
+ /* CAM_nPD */
+ MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x1b0b0
+ /* CAM_LOCK */
+ MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x1b0b0
+
+ /* USB ethernet reset (asix) */
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ /* WL_REG_ON */
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001f8b1
+ MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001f8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ /* No leds */
+ fsl,pins = <>;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ /* CS */
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ /* CAN2_nINT */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qp-vicutp.dts b/arch/arm/dts/imx6qp-vicutp.dts
new file mode 100644
index 0000000000..44cfe68867
--- /dev/null
+++ b/arch/arm/dts/imx6qp-vicutp.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include <arm/imx6qp.dtsi>
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+ model = "Kverneland UT1P Board";
+ compatible = "kvg,vicutp", "fsl,imx6qp";
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ /* phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; */
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6ul-prti6g.dts b/arch/arm/dts/imx6ul-prti6g.dts
new file mode 100644
index 0000000000..e65198bab2
--- /dev/null
+++ b/arch/arm/dts/imx6ul-prti6g.dts
@@ -0,0 +1,81 @@
+/*
+ * Copyright (C) 2016 Protonic Holland
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "imx6ul-prti6g.dtsi"
+
+/ {
+ model = "Protonic PRTI6G Board";
+ compatible = "prt,prti6g", "fsl,imx6ul";
+};
+
+&pinctrl_hog {
+ fsl,pins = <
+ /* HW revision detect */
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
+ MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
+ MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BOARD_ID0 */
+ MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 /* BOARD_ID1 */
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* BOARD_ID2 */
+ MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 /* BOARD_ID3 */
+
+ /* Safety controller IO */
+ MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* WAKE_SC */
+ MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* PROGRAM_SC */
+ >;
+};
+
+&ecspi2 {
+ status = "okay";
+};
+
+&can2 {
+ status = "okay";
+};
+
+&i2c2 {
+ can_adc: ads1015@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+};
diff --git a/arch/arm/dts/imx6ul-prti6g.dtsi b/arch/arm/dts/imx6ul-prti6g.dtsi
new file mode 100644
index 0000000000..c20bbd5bc2
--- /dev/null
+++ b/arch/arm/dts/imx6ul-prti6g.dtsi
@@ -0,0 +1,330 @@
+/*
+ * Copyright (C) 2016 Protonic Holland
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <arm/imx6ul.dtsi>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ environment@0 {
+ compatible = "barebox,environment";
+ device-path = &flash, "partname:env";
+ };
+ };
+
+ memory {
+ reg = <0x80000000 0x10000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p2v: 3p2-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-3P2V";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-always-on;
+ };
+
+ reg_1p35v: 1p35-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-1P35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ debug {
+ label = "debug0";
+ gpios = <&gpio4 16 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&usbotg1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p2v>;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash: w25q64fv@0 {
+ compatible = "winbond,w25q64", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x0 0x60000>; /* 384 Kb */
+ };
+
+ partition@60000 {
+ label = "env";
+ reg = <0x60000 0x10000>; /* 64 Kb */
+ };
+
+ partition@70000 {
+ label = "dtb";
+ reg = <0x70000 0x10000>; /* 64 Kb */
+ };
+
+ partition@80000 {
+ label = "kernel";
+ reg = <0x80000 0x780000>; /* 7680 Kb */
+ };
+ };
+};
+
+&ecspi2 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ /* RFID chip */
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ tmp103: tmp103@70 {
+ compatible = "ti,tmp103", "tmp103";
+ reg = <0x70>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1 &pinctrl_ethphy0_rst>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <11>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ prti6g {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* HW revision detect */
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
+ MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
+ MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BOARD_ID0 */
+ MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 /* BOARD_ID1 */
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* BOARD_ID2 */
+ MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 /* BOARD_ID3 */
+
+ /* CAN diagnostics (nSMBALERT) */
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__GPIO4_IO16 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
+ MX6UL_PAD_NAND_READY_B__GPIO4_IO12 0x170b0 /* SD1 CD */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x0b0b0
+ MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x000b1
+ MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x0b0b0
+ MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x0b0b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x0b0b0
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x000b1
+ MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x0b0b0
+ MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x0b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
+ MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_VSYNC__I2C2_SDA 0x4001b8b0
+ MX6UL_PAD_CSI_HSYNC__I2C2_SCL 0x4001b8b0
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x100b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x100b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ >;
+ };
+
+ pinctrl_ethphy0_rst: ethphy-rstgrp-0 {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x00880 /* PHY RESET */
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x0b0b0 /* SR */
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* TERM */
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x0b0b0 /* nSMBALERT */
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x0b0b0
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x0b0b0
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* SR */
+ >;
+ };
+ };
+};
--
2.27.0
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
