Hi Thorsten, On Fri, Apr 26, 2019 at 11:13:08AM +0200, Thorsten Scherer wrote: > --- > Documentation/boards/imx/amazon-kindle-3.rst | 10 +-- > Documentation/boards/omap.rst | 2 +- > Documentation/boards/openrisc.rst | 78 ++++++++++---------- > Documentation/boards/sandbox.rst | 4 +- > 4 files changed, 47 insertions(+), 47 deletions(-) > > diff --git a/Documentation/boards/imx/amazon-kindle-3.rst b/Documentation/boards/imx/amazon-kindle-3.rst > index 6b5d9fe53..93fbc10d9 100644 > --- a/Documentation/boards/imx/amazon-kindle-3.rst > +++ b/Documentation/boards/imx/amazon-kindle-3.rst > @@ -15,9 +15,9 @@ To upload and run a new bootloader the device can be put into USB-downloader > mode by the SOC microcode when Vol+ is pressed during startup. A new USB > device "SE Blank RINGO" should appear, barebox may be uploaded using > > -.. code-block:: console > +.. code-block:: sh > > - $ scripts/imx/imx-usb-loader barebox.imximg > + $ scripts/imx/imx-usb-loader barebox.imximg I don't understand why you change this to "sh", but let the lines still begin with "$"... > > Note: a USB serial ACM console will be launched by a barebox init script > when the cursor select key is pressed during startup (e.g. before running > @@ -28,7 +28,7 @@ When installing the barebox imximg on the eMMC take care not to overwrite > the partition table and vendor supplied serial numbers stored on the eMMC. > e.g. just write the imx-header and the application section: > > -.. code-block:: sh > +.. code-block:: console ... while here you're changing it to "console", and the lines don't start with a "$". Lines beginning with "$" are not valid sh scripts, so this looks wrong to me. > > - memcpy -b -s barebox.imximg -d /dev/disk0.imx_header 1024 0 1024 > - memcpy -b -s barebox.imximg -d /dev/disk0.self 4096 0 195584 > + memcpy -b -s barebox.imximg -d /dev/disk0.imx_header 1024 0 1024 > + memcpy -b -s barebox.imximg -d /dev/disk0.self 4096 0 195584 > diff --git a/Documentation/boards/omap.rst b/Documentation/boards/omap.rst > index 717a38fe0..700b1ef1e 100644 > --- a/Documentation/boards/omap.rst > +++ b/Documentation/boards/omap.rst > @@ -17,7 +17,7 @@ special partitioning). The same procedure can be used for barebox. With such a > card (assumed to be at /dev/sdc), the following can be used to build and install > barebox: > > -.. code-block:: console > +.. code-block:: sh > > # mount -t fat /dev/sdc1 /mnt > # make panda_xload_defconfig Same here, this would turn the lines into comments in sh, but the '#' is intended as a prompt marker (traditionally for the root prompt). - Roland > diff --git a/Documentation/boards/openrisc.rst b/Documentation/boards/openrisc.rst > index f9d67f965..838039e53 100644 > --- a/Documentation/boards/openrisc.rst > +++ b/Documentation/boards/openrisc.rst > @@ -6,52 +6,52 @@ or1ksim > > Compile or1ksim emulator: > > -.. code-block:: console > +.. code-block:: sh > > - $ cd ~/ > - $ git clone https://github.com/openrisc/or1ksim > - $ cd or1ksim > - $ ./configure > - $ make > + $ cd ~/ > + $ git clone https://github.com/openrisc/or1ksim > + $ cd or1ksim > + $ ./configure > + $ make > > Create minimal or1ksim.cfg file: > > .. code-block:: none > > - section cpu > - ver = 0x12 > - cfgr = 0x20 > - rev = 0x0001 > - end > - > - section memory > - name = "RAM" > - type = unknown > - baseaddr = 0x00000000 > - size = 0x02000000 > - delayr = 1 > - delayw = 2 > - end > - > - section uart > - enabled = 1 > - baseaddr = 0x90000000 > - irq = 2 > - 16550 = 1 > - /* channel = "tcp:10084" */ > - channel = "xterm:" > - end > - > - section ethernet > - enabled = 1 > - baseaddr = 0x92000000 > - irq = 4 > - rtx_type = "tap" > - tap_dev = "tap0" > - end > + section cpu > + ver = 0x12 > + cfgr = 0x20 > + rev = 0x0001 > + end > + > + section memory > + name = "RAM" > + type = unknown > + baseaddr = 0x00000000 > + size = 0x02000000 > + delayr = 1 > + delayw = 2 > + end > + > + section uart > + enabled = 1 > + baseaddr = 0x90000000 > + irq = 2 > + 16550 = 1 > + /* channel = "tcp:10084" */ > + channel = "xterm:" > + end > + > + section ethernet > + enabled = 1 > + baseaddr = 0x92000000 > + irq = 4 > + rtx_type = "tap" > + tap_dev = "tap0" > + end > > Run or1ksim: > > -.. code-block:: console > +.. code-block:: sh > > - $ ~/or1ksim/sim -f or1ksim.cfg barebox > + $ ~/or1ksim/sim -f or1ksim.cfg barebox > diff --git a/Documentation/boards/sandbox.rst b/Documentation/boards/sandbox.rst > index 85a54e6b0..b5673a0df 100644 > --- a/Documentation/boards/sandbox.rst > +++ b/Documentation/boards/sandbox.rst > @@ -17,9 +17,9 @@ The barebox sandbox can be built with the host compiler: > Running the sandbox > ------------------- > > -Once you compile barebox for the sandbox, you can run it with:: > +Once you compile barebox for the sandbox, you can run it with: > > -.. code-block:: console > +.. code-block:: sh > > $ barebox [<OPTIONS>] > > -- > 2.20.1 > > > _______________________________________________ > barebox mailing list > barebox@xxxxxxxxxxxxxxxxxxx > http://lists.infradead.org/mailman/listinfo/barebox > -- Roland Hieber | r.hieber@xxxxxxxxxxxxxx | Pengutronix e.K. | https://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim | Phone: +49-5121-206917-5086 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
