Port of a Linux commit 68a0bfec72cb4f117198ae31df114dad4c5e405d
When we have only two view ports in a DesignWare PCIe platform, iatu0
is used for both CFG and IO accesses. When CFGs are sent to peripherals
(e.g., lspci), iatu0 frequently switches between CFG and IO.
For such scenarios, a MEMORY might be sent as an IOs by mistake.
Considering the following configurations:
MEMORY -> BASE_ADDR: 0xb4100000, LIMIT: 0xb4100FFF, TYPE=mem
CFG -> BASE_ADDR: 0xb4000000, LIMIT: 0xb4000FFF, TYPE=cfg
IO -> BASE_ADDR: 0xFFFFFFFF, LIMIT: 0xFFFFFFFE, TYPE=io
Suppose PCIe has just completed a CFG access. To switch back to IO, it
sets the BASE_ADDR to 0xFFFFFFFF, LIMIT 0xFFFFFFFE and TYPE to IO. When
another CFG comes, the BASE_ADDR is set to 0xb4000000 to switch to CFG. At
this moment, a MEMORY access shows up, since it matches with iatu0 (due to
0xb4000000 <= MEMORY BASE_ADDR <= MEMORY LIMIT <= 0xFFFFFFF), it is treated
as an IO access by mistake, then sent to perpheral.
This patch fixes the problem by exchanging the assignments of `MEMORYs' and
`CFGs/IOs', which assigning MEMORYs to iatu0, CFGs and IOs to iatu1.
We can still have issues with IO transfer, however memory transfer is used
predominantly therefore we are just minimizing the risk of failure.
Actually, we can not do much when we have only two viewports. We can
either not allow the less frequent IO transfers at all, or can live with a
remote possibility of getting it corrupted.
Signed-off-by: Dong Bo <dongbo4@xxxxxxxxxx>
[pratyush.anand@xxxxxxxxx: Modified commit log to capture remote risk]
Signed-off-by: Pratyush Anand <pratyush.anand@xxxxxxxxx>
Signed-off-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Signed-off-by: Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
---
drivers/pci/pcie-designware.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/pci/pcie-designware.c b/drivers/pci/pcie-designware.c
index cf1b3032e..817d70850 100644
--- a/drivers/pci/pcie-designware.c
+++ b/drivers/pci/pcie-designware.c
@@ -377,12 +377,12 @@ static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
va_cfg_base = pp->va_cfg1_base;
}
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
type, cpu_addr,
busdev, cfg_size);
ret = dw_pcie_cfg_read(va_cfg_base + where, size, val);
if (pp->num_viewport <= 2)
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
PCIE_ATU_TYPE_IO, pp->io_mod_base,
pp->io_bus_addr, pp->io_size);
@@ -416,12 +416,12 @@ static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
va_cfg_base = pp->va_cfg1_base;
}
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
type, cpu_addr,
busdev, cfg_size);
ret = dw_pcie_cfg_write(va_cfg_base + where, size, val);
if (pp->num_viewport <= 2)
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
PCIE_ATU_TYPE_IO, pp->io_mod_base,
pp->io_bus_addr, pp->io_size);
@@ -572,7 +572,7 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
* we should not program the ATU here.
*/
if (!pp->ops->rd_other_conf) {
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
PCIE_ATU_TYPE_MEM, pp->mem_mod_base,
pp->mem_bus_addr, pp->mem_size);
if (pp->num_viewport <= 2)
--
2.19.1
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
