On Thu, Aug 23, 2018 at 2:59 AM Florian Bäuerle
<florian.baeuerle@xxxxxxxxxxxx> wrote:
>
> Signed-off-by: Florian Bäuerle <florian.baeuerle@xxxxxxxxxxxx>
> ---
> arch/arm/boards/phytec-phycard-imx27/lowlevel.c | 15 +++++++++++++++
> arch/arm/mach-imx/include/mach/debug_ll.h | 13 +++++++++++++
> include/serial/imx-uart.h | 5 +++++
> 3 files changed, 33 insertions(+)
>
> diff --git a/arch/arm/boards/phytec-phycard-imx27/lowlevel.c b/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> index e1132e0..8244337 100644
> --- a/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> +++ b/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> @@ -14,6 +14,8 @@
> #include <mach/imx-pll.h>
> #include <mach/esdctl.h>
> #include <mach/imx-nand.h>
> +#include <mach/debug_ll.h>
> +#include <serial/imx-uart.h>
>
> #define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
>
> @@ -58,6 +60,18 @@ static void sdram_init(void)
> MX27_ESDCTL_BASE_ADDR + IMX_ESDCTL0);
> }
>
> +static void setup_uart(void)
> +{
> + /* Set PE[12-15] use, direction, function and pull-up */
> + writel(0xfffc0f27, MX27_GPIO5_BASE_ADDR + 0x20);
> + writel(0x00005000, MX27_GPIO5_BASE_ADDR);
> + writel(0x00000000, MX27_GPIO5_BASE_ADDR + 0x38);
> + writel(0xffff0fff, MX27_GPIO5_BASE_ADDR + 0x40);
> +
Can constants from iomux-imx27.h be used here?
> + imx27_ungate_all_peripherals();
> + imx27_uart_setup_ll();
> +}
> +
> void __bare_init __naked phytec_phycard_imx27_common_init(void *fdt)
> {
> unsigned long r;
> @@ -97,6 +111,7 @@ void __bare_init __naked phytec_phycard_imx27_common_init(void *fdt)
> MX27_CSCR_MSHC_SEL, MX27_CCM_BASE_ADDR + MX27_CSCR);
>
> sdram_init();
> + setup_uart();
Majority of the boards gates this to happen on if
IS_ENABLED(CONFIG_DEBUG_LL) is true, so it might make sense to do the
same.
>
> imx27_barebox_boot_nand_external(fdt);
> }
> diff --git a/arch/arm/mach-imx/include/mach/debug_ll.h b/arch/arm/mach-imx/include/mach/debug_ll.h
> index 1550e05..6c9b21d 100644
> --- a/arch/arm/mach-imx/include/mach/debug_ll.h
> +++ b/arch/arm/mach-imx/include/mach/debug_ll.h
> @@ -56,6 +56,12 @@
> #error "unknown i.MX debug uart soc type"
> #endif
>
> +static inline void imx27_uart_setup_ll(void) {
> + void *base = IOMEM(IMX_UART_BASE(IMX_DEBUG_SOC,
> + CONFIG_DEBUG_IMX_UART_PORT));
> + imx27_uart_setup(base);
> +}
> +
> static inline void imx50_uart_setup_ll(void)
> {
> void *base = IOMEM(IMX_UART_BASE(IMX_DEBUG_SOC, CONFIG_DEBUG_IMX_UART_PORT));
> @@ -121,6 +127,7 @@ static inline void PUTC_LL(int c)
>
> #else
>
> +static inline void imx27_uart_setup_ll(void) {}
> static inline void imx50_uart_setup_ll(void) {}
> static inline void imx51_uart_setup_ll(void) {}
> static inline void imx53_uart_setup_ll(void) {}
> @@ -138,6 +145,12 @@ static inline void imx_ungate_all_peripherals(void __iomem *ccmbase)
> writel(0xffffffff, ccmbase + i);
> }
>
> +static inline void imx27_ungate_all_peripherals(void)
> +{
> + writel(0xfffffbff, IOMEM(MX27_CCM_BASE_ADDR) + 0x20);
> + writel(0xfffffffc, IOMEM(MX27_CCM_BASE_ADDR) + 0x24);
> +}
I think you can use MX27_PCCR0 and MX27_PCCR1 here instead of magic numbers.
> +
> static inline void imx6_ungate_all_peripherals(void)
> {
> imx_ungate_all_peripherals(IOMEM(MX6_CCM_BASE_ADDR));
> diff --git a/include/serial/imx-uart.h b/include/serial/imx-uart.h
> index c236065..0c033c2 100644
> --- a/include/serial/imx-uart.h
> +++ b/include/serial/imx-uart.h
> @@ -155,6 +155,11 @@ static inline void imx_uart_set_dte(void __iomem *uartbase)
> writel(ufcr, uartbase + UFCR);
> }
>
> +static inline void imx27_uart_setup(void __iomem *uartbase)
> +{
> + imx_uart_setup(uartbase, 66500000);
> +}
> +
> static inline void imx50_uart_setup(void __iomem *uartbase)
> {
> imx_uart_setup(uartbase, 66666666);
> --
> 1.8.3.1
>
>
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
