Re: [PATCH] ARM: Add Advantech imx6 board support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Christoph,

On Thu, Apr 05, 2018 at 03:15:49PM +0200, Christoph Fritz wrote:
> +	phy_register_fixup_for_uid(0x004dd072, 0xffffffef, ar8035_phy_fixup);
> +
> +	switch (bootsource_get()) {
> +	case BOOTSOURCE_MMC:
> +		environment_path = basprintf("/chosen/environment-sd%d",
> +					     bootsource_get_instance() + 1);
> +		envdev = "MMC";
> +		break;
> +	case BOOTSOURCE_SPI:
> +	default:
> +		environment_path = basprintf("/chosen/environment-sd4");
> +		envdev = "MMC";
> +		break;
> +	}
> +
> +	if (environment_path) {
> +		ret = of_device_enable_path(environment_path);
> +		if (ret < 0)
> +			pr_warn("Failed to enable env partition '%s' (%d)\n",
> +				environment_path, ret);
> +		free(environment_path);
> +	}
> +
> +	pr_notice("Using environment in %s\n", envdev);

This is always "MMC", not very informative. Maybe "eMMC" and "external
SD"?

> +
> +	imx6_bbu_internal_mmc_register_handler("mmc3", "/dev/mmc3",
> +						BBU_HANDLER_FLAG_DEFAULT);

That would be the eMMC, right? For this I can recommend putting barebox
into the boot partitions of the eMMC. Normally there are two of them
and with imx6_bbu_internal_mmcboot_register_handler() you even get a
robust barebox A/B update mechanism.

> +
> +	return 0;
> +}
> +device_initcall(advantech_mx6_devices_init);
> diff --git a/arch/arm/boards/advantech-mx6/flash-header-advantech-rom-7421.imxcfg b/arch/arm/boards/advantech-mx6/flash-header-advantech-rom-7421.imxcfg
> new file mode 100644
> index 0000000..611e06b
> --- /dev/null
> +++ b/arch/arm/boards/advantech-mx6/flash-header-advantech-rom-7421.imxcfg
> @@ -0,0 +1,73 @@
> +soc imx6
> +loadaddr 0x10000000
> +dcdofs 0x400
> +
> +wm 32 0x020e0774 0x000C0000

[...]

> +wm 32 0x021b0004 0x0002556D
> +wm 32 0x021b0404 0x00011006
> +wm 32 0x021b001c 0x00000000

> +wm 32 0x020c4068 0x00C03F3F
> +wm 32 0x020c406c 0x0030FC03
> +wm 32 0x020c4070 0x0FFFC000
> +wm 32 0x020c4074 0x3FF00000
> +wm 32 0x020c4078 0x00FFF300
> +wm 32 0x020c407c 0x0F0000C3
> +wm 32 0x020c4080 0x000003FF

Please remove writing these clock registers here. The registers get
overwritten in a few moments by barebox anyway. Often enough these gate
settings disable the USB clocks and then booting this image from USB is
no longer possible.

> +wm 32 0x020e0010 0xF00000CF
> +wm 32 0x020e0018 0x007F007F
> +wm 32 0x020e001c 0x007F007F
> diff --git a/arch/arm/boards/advantech-mx6/lowlevel.c b/arch/arm/boards/advantech-mx6/lowlevel.c
> new file mode 100644
> index 0000000..5efb91a
> --- /dev/null
> +++ b/arch/arm/boards/advantech-mx6/lowlevel.c
> @@ -0,0 +1,58 @@
> +/*
> + * Copyright (C) 2018 Christoph Fritz <chf.fritz@xxxxxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <debug_ll.h>
> +#include <common.h>
> +#include <asm/barebox-arm-head.h>
> +#include <asm/barebox-arm.h>
> +#include <image-metadata.h>
> +#include <mach/generic.h>
> +#include <mach/esdctl.h>
> +#include <linux/sizes.h>
> +
> +static inline void setup_uart(void)
> +{
> +	void __iomem *iomuxbase = (void *)MX6_IOMUXC_BASE_ADDR;
> +
> +	writel(0x3, iomuxbase + 0x4c);
> +
> +	imx6_ungate_all_peripherals();
> +	imx6_uart_setup_ll();
> +
> +	putc_ll('>');
> +}
> +
> +extern char __dtb_imx6dl_advantech_rom_7421_start[];
> +
> +BAREBOX_IMD_TAG_STRING(advantech_imx6dl_memsize_512M, IMD_TYPE_PARAMETER,
> +		       "memsize=512", 0);
> +
> +ENTRY_FUNCTION(start_advantech_imx6dl_rom_7421, r0, r1, r2)
> +{
> +	void *fdt;
> +
> +	imx6_cpu_lowlevel_init();
> +
> +	arm_setup_stack(0x00920000 - 8);
> +
> +	IMD_USED(advantech_imx6dl_memsize_512M);
> +
> +	if (IS_ENABLED(CONFIG_DEBUG_LL))
> +		setup_uart();
> +
> +	fdt = __dtb_imx6dl_advantech_rom_7421_start - get_runtime_offset();

Since "a43e2bbc46 ARM: return positive offset in get_runtime_offset()"
this must be '+' get_runtime_offset();

> +#include <dt-bindings/gpio/gpio.h>
> +#include <arm/imx6dl.dtsi>
> +#include "imx6dl.dtsi"
> +
> +/ {
> +	model = "Advantech i.MX6 ROM-7421";
> +	compatible = "advantech,imx6dl-rom-7421", "fsl,imx6dl";
> +
> +	chosen {
> +		linux,stdout-path = &uart1;

just stdout-path. linux,stdout-path is the old binding.

> +
> +		environment-sd2 {			/* Micro SD */
> +			compatible = "barebox,environment";
> +			device-path = &usdhc2, "partname:barebox-environment";
> +			status = "disabled";
> +		};
> +
> +		environment-sd4 {			/* eMMC */
> +			compatible = "barebox,environment";
> +			device-path = &usdhc4, "partname:barebox-environment";
> +			status = "disabled";
> +		};
> +	};
> +};
> +
> +&ecspi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi1>;
> +	fsl,spi-num-chipselects = <1>;
> +	cs-gpios = <&gpio3 19 0>;
> +	status = "okay";
> +
> +	flash: m25p80@0 {
> +		compatible = "m25p80";
> +		spi-max-frequency = <20000000>;
> +		reg = <0>;
> +		status = "okay";
> +
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +
> +		partition@400 {
> +			label = "SPL";
> +			reg = <0x400 0xa0000>;
> +		};
> +
> +		partition@d0000 {
> +			label = "MAC";
> +			reg = <0xd0000 0x1000>;
> +		};

What's in the free space? If you can use the space up to 0xd0000 then
you could put a full barebox before it instead of just a SPL (I guess
this partitioning comes from the original vendor, right?)

> +	};
> +};
> +
> +&usdhc4 {					/* eMMC */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc4>;
> +	bus-width = <8>;
> +	non-removable;
> +	no-1-8-v;
> +	status = "okay";
> +
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +	partition@400 {
> +		label = "CRC";
> +		reg = <0x200000 0x200>;
> +	};
> +
> +	partition@600 {
> +		label = "barebox_CRCed";
> +		reg = <0x200200 0x96000>;
> +	};
> +
> +	partition@96600 {
> +		label = "barebox-environment";
> +		reg = <0x296200 0x20000>;
> +	};

the @adr in the partition names do not match the actual start of the
partitions, this should be fixed. Overall the partitions look strange.
Aren't barebox_CRCed and barebox-environment in somewhere in the middle
of the device which is already occupied by the regular partitions?

> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +
> +	imx6dl-advantech-rom-742 {

This additional subnode is obsolete, please remove and move the pinctrl
nodes one level up.

> diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
> index eb135c3..e4de3d1 100644
> --- a/arch/arm/mach-imx/Kconfig
> +++ b/arch/arm/mach-imx/Kconfig
> @@ -39,6 +39,7 @@ config ARCH_TEXT_BASE
>  	default 0x4fc00000 if MACH_UDOO
>  	default 0x4fc00000 if MACH_VARISCITE_MX6
>  	default 0x4fc00000 if MACH_PHYTEC_SOM_IMX6
> +	default 0x4fc00000 if MACH_ADVANTECH_ROM_742X

You shouldn't need this.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox



[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux