From: Juergen Borleis <jbe@xxxxxxxxxxxxxx> Signed-off-by Juergen Borleis <jbe@xxxxxxxxxxxxxx> Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> --- Documentation/boards/imx/Element14-WaRP7.rst | 54 +++++++++++++++ arch/arm/boards/Makefile | 1 + arch/arm/boards/element14-warp7/Makefile | 2 + arch/arm/boards/element14-warp7/board.c | 35 ++++++++++ .../element14-warp7/flash-header-mx7-warp.imxcfg | 81 ++++++++++++++++++++++ arch/arm/boards/element14-warp7/lowlevel.c | 48 +++++++++++++ arch/arm/dts/Makefile | 1 + arch/arm/dts/imx7s-warp.dts | 45 ++++++++++++ arch/arm/mach-imx/Kconfig | 5 ++ images/Makefile.imx | 5 ++ 10 files changed, 277 insertions(+) create mode 100644 Documentation/boards/imx/Element14-WaRP7.rst create mode 100644 arch/arm/boards/element14-warp7/Makefile create mode 100644 arch/arm/boards/element14-warp7/board.c create mode 100644 arch/arm/boards/element14-warp7/flash-header-mx7-warp.imxcfg create mode 100644 arch/arm/boards/element14-warp7/lowlevel.c create mode 100644 arch/arm/dts/imx7s-warp.dts diff --git a/Documentation/boards/imx/Element14-WaRP7.rst b/Documentation/boards/imx/Element14-WaRP7.rst new file mode 100644 index 000000000..d4e5e7991 --- /dev/null +++ b/Documentation/boards/imx/Element14-WaRP7.rst @@ -0,0 +1,54 @@ +element14 WaRP7 +=============== + +This CPU card is based on an NXP i.MX7S SoC. + +Supported hardware +================== + +- NXP PMIC PFUZE3000 +- Kingston 08EMCP04-EL3AV100 eMCP (eMMC and LPDDR3 memory in one package) + - 8 GiB eMMC Triple-Level cell NAND flash, eMMC standard 5.0 (HS400) + - 512 MiB LPDDR3 SDRAM starting at address 0x80000000 + +Bootstrapping barebox +===================== + +The device boots in internal boot mode from eMMC and is shipped with a +vendor modified u-boot imximage. + +Barebox can be used as a drop-in replacement for the shipped bootloader. + +The WaRP7 IO Board has a double DIP switch where switch number two defines the +boot source of the i.MX7 SoC: + + +-----+ + | | + | | O | <--- on = high level + | | | | + | O | | <--- off = low level + | | + | 1 2 | + +-----+ + +Bootsource is the internal eMMC: + + +-----+ + | | + | O | | + | | | | + | | O | <---- eMMC + | | + | 1 2 | + +-----+ + +Bootsource is the USB: + + +-----+ + | | + | O O | <---- USB + | | | | + | | | | + | | + | 1 2 | + +-----+ diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile index ff0a86fcb..2dec84d8c 100644 --- a/arch/arm/boards/Makefile +++ b/arch/arm/boards/Makefile @@ -140,4 +140,5 @@ obj-$(CONFIG_MACH_ZYLONITE) += zylonite/ obj-$(CONFIG_MACH_VARISCITE_MX6) += variscite-mx6/ obj-$(CONFIG_MACH_VSCOM_BALTOS) += vscom-baltos/ obj-$(CONFIG_MACH_QEMU_VIRT64) += qemu-virt64/ +obj-$(CONFIG_MACH_WARP7) += element14-warp7/ obj-$(CONFIG_MACH_VF610_TWR) += freescale-vf610-twr/ diff --git a/arch/arm/boards/element14-warp7/Makefile b/arch/arm/boards/element14-warp7/Makefile new file mode 100644 index 000000000..01c7a259e --- /dev/null +++ b/arch/arm/boards/element14-warp7/Makefile @@ -0,0 +1,2 @@ +obj-y += board.o +lwl-y += lowlevel.o diff --git a/arch/arm/boards/element14-warp7/board.c b/arch/arm/boards/element14-warp7/board.c new file mode 100644 index 000000000..84fc885da --- /dev/null +++ b/arch/arm/boards/element14-warp7/board.c @@ -0,0 +1,35 @@ +/* + * Copyright (C) 2017 Sascha Hauer, Pengutronix + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <common.h> +#include <init.h> +#include <environment.h> +#include <mach/bbu.h> +#include <asm/armlinux.h> +#include <generated/mach-types.h> +#include <partition.h> +#include <mach/generic.h> +#include <linux/sizes.h> + +static int warp7_devices_init(void) +{ + if (!of_machine_is_compatible("warp,imx7s-warp")) + return 0; + + imx6_bbu_internal_mmc_register_handler("mmc", "/dev/mmc2.boot0.barebox", + BBU_HANDLER_FLAG_DEFAULT); + + return 0; +} +device_initcall(warp7_devices_init); diff --git a/arch/arm/boards/element14-warp7/flash-header-mx7-warp.imxcfg b/arch/arm/boards/element14-warp7/flash-header-mx7-warp.imxcfg new file mode 100644 index 000000000..a3389218d --- /dev/null +++ b/arch/arm/boards/element14-warp7/flash-header-mx7-warp.imxcfg @@ -0,0 +1,81 @@ +/* + * Copyright (C) 2016 NXP Semiconductors + * + * SPDX-License-Identifier: GPL-2.0 + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +soc imx7 +loadaddr 0x80000000 +dcdofs 0x400 + +wm 32 0x30340004 0x4F400005 + +wm 32 0x30391000 0x00000002 +wm 32 0x307a0000 0x03040008 +wm 32 0x307a0064 0x00200038 +wm 32 0x307a0490 0x00000001 +wm 32 0x307a00d0 0x00350001 +wm 32 0x307a00dc 0x00c3000a +wm 32 0x307a00e0 0x00010000 +wm 32 0x307a00e4 0x00110006 +wm 32 0x307a00f4 0x0000033f +wm 32 0x307a0100 0x0a0e110b +wm 32 0x307a0104 0x00020211 +wm 32 0x307a0108 0x03060708 +wm 32 0x307a010c 0x00a0500c +wm 32 0x307a0110 0x05020307 +wm 32 0x307a0114 0x02020404 +wm 32 0x307a0118 0x02020003 +wm 32 0x307a011c 0x00000202 +wm 32 0x307a0120 0x00000202 + +wm 32 0x307a0180 0x00600018 +wm 32 0x307a0184 0x00e00100 +wm 32 0x307a0190 0x02098205 +wm 32 0x307a0194 0x00060303 +wm 32 0x307a01a0 0x80400003 +wm 32 0x307a01a4 0x00100020 +wm 32 0x307a01a8 0x80100004 + +wm 32 0x307a0200 0x00000015 +wm 32 0x307a0204 0x00161616 +wm 32 0x307a0210 0x00000f0f +wm 32 0x307a0214 0x04040404 +wm 32 0x307a0218 0x0f0f0404 + +wm 32 0x307a0240 0x06000600 +wm 32 0x307a0244 0x00000000 +wm 32 0x30391000 0x00000000 +wm 32 0x30790000 0x17421e40 +wm 32 0x30790004 0x10210100 +wm 32 0x30790008 0x00010000 +wm 32 0x30790010 0x0007080c +wm 32 0x307900b0 0x1010007e + +wm 32 0x3079001C 0x01010000 +wm 32 0x3079009c 0x00000d6e + +wm 32 0x30790030 0x06060606 +wm 32 0x30790020 0x0a0a0a0a +wm 32 0x30790050 0x01000008 +wm 32 0x30790050 0x00000008 +wm 32 0x30790018 0x0000000f +wm 32 0x307900c0 0x0e487304 +wm 32 0x307900c0 0x0e4c7304 +wm 32 0x307900c0 0x0e4c7306 +wm 32 0x307900c0 0x0e4c7304 + +check 32 while_any_bit_clear 0x307900c4 0x1 + +wm 32 0x307900c0 0x0e487304 + +wm 32 0x30384130 0x00000000 +wm 32 0x30340020 0x00000178 +wm 32 0x30384130 0x00000002 + +check 32 while_any_bit_clear 0x307a0004 0x1 diff --git a/arch/arm/boards/element14-warp7/lowlevel.c b/arch/arm/boards/element14-warp7/lowlevel.c new file mode 100644 index 000000000..98d8b6436 --- /dev/null +++ b/arch/arm/boards/element14-warp7/lowlevel.c @@ -0,0 +1,48 @@ +#define DEBUG +#include <io.h> +#include <common.h> +#include <linux/sizes.h> +#include <mach/generic.h> +#include <asm/barebox-arm-head.h> +#include <asm/barebox-arm.h> +#include <mach/debug_ll.h> +#include <asm/cache.h> + +extern char __dtb_imx7s_warp_start[]; + +static noinline void warp7_start(void) +{ + void __iomem *iomuxbase = IOMEM(MX7_IOMUX_BASE_ADDR); + void __iomem *uart = IOMEM(MX7_UART1_BASE_ADDR); + void __iomem *ccmbase = IOMEM(MX7_CCM_BASE_ADDR); + void *fdt; + + writel(0x3, ccmbase + 0x4000 + 16 * 148 + 0x8); + writel(0x10000000, ccmbase + 0x8000 + 128 * 95); + writel(0x3, ccmbase + 0x4000 + 16 * 148 + 0x4); + writel(0x0, iomuxbase + 0x128); + writel(0x0, iomuxbase + 0x12c); + + imx7_uart_setup(uart); + + pbl_set_putc(imx_uart_putc, uart); + + pr_debug("Element14 i.MX7 Warp\n"); + + fdt = __dtb_imx7s_warp_start - get_runtime_offset(); + + barebox_arm_entry(0x80000000, SZ_512M, fdt); +} + +ENTRY_FUNCTION(start_imx7s_element14_warp7, r0, r1, r2) +{ + imx7_cpu_lowlevel_init(); + + arm_early_mmu_cache_invalidate(); + + relocate_to_current_adr(); + setup_c(); + barrier(); + + warp7_start(); +} \ No newline at end of file diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 8ba99577e..6b2fa34f2 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -79,6 +79,7 @@ pbl-dtb-$(CONFIG_MACH_UDOO) += imx6q-udoo.dtb.o pbl-dtb-$(CONFIG_MACH_USI_TOPKICK) += kirkwood-topkick-bb.dtb.o pbl-dtb-$(CONFIG_MACH_VARISCITE_MX6) += imx6q-var-custom.dtb.o pbl-dtb-$(CONFIG_MACH_VSCOM_BALTOS) += am335x-baltos-minimal.dtb.o +pbl-dtb-$(CONFIG_MACH_WARP7) += imx7s-warp.dtb.o pbl-dtb-$(CONFIG_MACH_VF610_TWR) += vf610-twr.dtb.o clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts *.dtb.lzo diff --git a/arch/arm/dts/imx7s-warp.dts b/arch/arm/dts/imx7s-warp.dts new file mode 100644 index 000000000..8741c1384 --- /dev/null +++ b/arch/arm/dts/imx7s-warp.dts @@ -0,0 +1,45 @@ +/* + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <arm/imx7s-warp.dts> +#include "imx7s.dtsi" + +/ { + chosen { + stdout-path = &uart1; + + environment@0 { + compatible = "barebox,environment"; + device-path = &bareboxenv; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; + }; +}; + +&usdhc3 { + boot0-partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + barebox@0 { + label = "barebox"; + reg = <0x0 0x300000>; + }; + + bareboxenv: bareboxenv@300000 { + label = "bareboxenv"; + reg = <0x300000 0x0>; + }; + }; +}; \ No newline at end of file diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index fd1ecb6bb..f371ee075 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -39,6 +39,7 @@ config ARCH_TEXT_BASE default 0x4fc00000 if MACH_UDOO default 0x4fc00000 if MACH_VARISCITE_MX6 default 0x4fc00000 if MACH_PHYTEC_SOM_IMX6 + default 0x9fc00000 if MACH_WARP7 config ARCH_IMX_IMXIMAGE bool @@ -350,6 +351,10 @@ config MACH_CM_FX6 bool "CM FX6" select ARCH_IMX6 +config MACH_WARP7 + bool "NXP i.MX7: element 14 WaRP7 Board" + select ARCH_IMX7 + config MACH_VF610_TWR bool "Freescale VF610 Tower Board" select ARCH_VF610 diff --git a/images/Makefile.imx b/images/Makefile.imx index 3b911ec13..08c804888 100644 --- a/images/Makefile.imx +++ b/images/Makefile.imx @@ -409,6 +409,11 @@ CFG_start_imx6dl_eltec_hipercam.pblx.imximg = $(board)/eltec-hipercam/flash-head FILE_barebox-eltec-hipercam.img = start_imx6dl_eltec_hipercam.pblx.imximg image-$(CONFIG_MACH_ELTEC_HIPERCAM) += barebox-eltec-hipercam.img +pblx-$(CONFIG_MACH_WARP7) += start_imx7s_element14_warp7 +CFG_start_imx7s_element14_warp7.pblx.imximg = $(board)/element14-warp7/flash-header-mx7-warp.imxcfg +FILE_barebox-element14-imx7s-warp7.img = start_imx7s_element14_warp7.pblx.imximg +image-$(CONFIG_MACH_WARP7) += barebox-element14-imx7s-warp7.img + pblx-$(CONFIG_MACH_VF610_TWR) += start_vf610_twr CFG_start_vf610_twr.pblx.imximg = $(board)/freescale-vf610-twr/flash-header-vf610-twr.imxcfg FILE_barebox-vf610-twr.img = start_vf610_twr.pblx.imximg -- 2.11.0 _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox