The TX6 boards come with 3 different PMIC variants from which we
currently only support the ltc3673. Detect the other two by i2c
address and set them up correctly. The code is based on the karo
U-Boot port.
Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
---
arch/arm/boards/karo-tx6x/Makefile | 1 +
arch/arm/boards/karo-tx6x/board.c | 167 +++++++------------------------
arch/arm/boards/karo-tx6x/pmic-ltc3676.c | 149 +++++++++++++++++++++++++++
arch/arm/boards/karo-tx6x/pmic-rn5t567.c | 154 ++++++++++++++++++++++++++++
arch/arm/boards/karo-tx6x/pmic-rn5t618.c | 152 ++++++++++++++++++++++++++++
arch/arm/boards/karo-tx6x/pmic.h | 8 ++
6 files changed, 501 insertions(+), 130 deletions(-)
create mode 100644 arch/arm/boards/karo-tx6x/pmic-ltc3676.c
create mode 100644 arch/arm/boards/karo-tx6x/pmic-rn5t567.c
create mode 100644 arch/arm/boards/karo-tx6x/pmic-rn5t618.c
create mode 100644 arch/arm/boards/karo-tx6x/pmic.h
diff --git a/arch/arm/boards/karo-tx6x/Makefile b/arch/arm/boards/karo-tx6x/Makefile
index 01c7a25..51b7c2d 100644
--- a/arch/arm/boards/karo-tx6x/Makefile
+++ b/arch/arm/boards/karo-tx6x/Makefile
@@ -1,2 +1,3 @@
obj-y += board.o
lwl-y += lowlevel.o
+obj-y += pmic-ltc3676.o pmic-rn5t567.o pmic-rn5t618.o
diff --git a/arch/arm/boards/karo-tx6x/board.c b/arch/arm/boards/karo-tx6x/board.c
index b955b81..6cb4689 100644
--- a/arch/arm/boards/karo-tx6x/board.c
+++ b/arch/arm/boards/karo-tx6x/board.c
@@ -26,122 +26,40 @@
#include <mach/bbu.h>
#include <mach/imx6.h>
#include <mfd/imx6q-iomuxc-gpr.h>
+#include "pmic.h"
#define ETH_PHY_RST IMX_GPIO_NR(7, 6)
#define ETH_PHY_PWR IMX_GPIO_NR(3, 20)
#define ETH_PHY_INT IMX_GPIO_NR(7, 1)
-#define DIV_ROUND(n,d) (((n) + ((d)/2)) / (d))
-
-#define LTC3676_BUCK1 0x01
-#define LTC3676_BUCK2 0x02
-#define LTC3676_BUCK3 0x03
-#define LTC3676_BUCK4 0x04
-#define LTC3676_DVB1A 0x0A
-#define LTC3676_DVB1B 0x0B
-#define LTC3676_DVB2A 0x0C
-#define LTC3676_DVB2B 0x0D
-#define LTC3676_DVB3A 0x0E
-#define LTC3676_DVB3B 0x0F
-#define LTC3676_DVB4A 0x10
-#define LTC3676_DVB4B 0x11
-#define LTC3676_MSKPG 0x13
-#define LTC3676_CLIRQ 0x1f
-
-#define LTC3676_BUCK_DVDT_FAST (1 << 0)
-#define LTC3676_BUCK_KEEP_ALIVE (1 << 1)
-#define LTC3676_BUCK_CLK_RATE_LOW (1 << 2)
-#define LTC3676_BUCK_PHASE_SEL (1 << 3)
-#define LTC3676_BUCK_ENABLE_300 (1 << 4)
-#define LTC3676_BUCK_PULSE_SKIP (0 << 5)
-#define LTC3676_BUCK_BURST_MODE (1 << 5)
-#define LTC3676_BUCK_CONTINUOUS (2 << 5)
-#define LTC3676_BUCK_ENABLE (1 << 7)
-
-#define LTC3676_PGOOD_MASK (1 << 5)
-
-#define LTC3676_MSKPG_BUCK1 (1 << 0)
-#define LTC3676_MSKPG_BUCK2 (1 << 1)
-#define LTC3676_MSKPG_BUCK3 (1 << 2)
-#define LTC3676_MSKPG_BUCK4 (1 << 3)
-#define LTC3676_MSKPG_LDO2 (1 << 5)
-#define LTC3676_MSKPG_LDO3 (1 << 6)
-#define LTC3676_MSKPG_LDO4 (1 << 7)
-
-#define VDD_IO_VAL mV_to_regval(vout_to_vref(3300 * 10, 5))
-#define VDD_IO_VAL_LP mV_to_regval(vout_to_vref(3100 * 10, 5))
-#define VDD_IO_VAL_2 mV_to_regval(vout_to_vref(3300 * 10, 5_2))
-#define VDD_IO_VAL_2_LP mV_to_regval(vout_to_vref(3100 * 10, 5_2))
-#define VDD_SOC_VAL mV_to_regval(vout_to_vref(1425 * 10, 6))
-#define VDD_SOC_VAL_LP mV_to_regval(vout_to_vref(900 * 10, 6))
-#define VDD_DDR_VAL mV_to_regval(vout_to_vref(1500 * 10, 7))
-#define VDD_DDR_VAL_LP mV_to_regval(vout_to_vref(1500 * 10, 7))
-#define VDD_CORE_VAL mV_to_regval(vout_to_vref(1425 * 10, 8))
-#define VDD_CORE_VAL_LP mV_to_regval(vout_to_vref(900 * 10, 8))
-
-/* LDO1 */
-#define R1_1 470
-#define R2_1 150
-/* LDO4 */
-#define R1_4 470
-#define R2_4 150
-/* Buck1 */
-#define R1_5 390
-#define R2_5 110
-#define R1_5_2 470
-#define R2_5_2 150
-/* Buck2 (SOC) */
-#define R1_6 150
-#define R2_6 180
-/* Buck3 (DDR) */
-#define R1_7 150
-#define R2_7 140
-/* Buck4 (CORE) */
-#define R1_8 150
-#define R2_8 180
-
-/* calculate voltages in 10mV */
-#define R1(idx) R1_##idx
-#define R2(idx) R2_##idx
-
-#define vout_to_vref(vout, idx) ((vout) * R2(idx) / (R1(idx) + R2(idx)))
-#define vref_to_vout(vref, idx) DIV_ROUND_UP((vref) * (R1(idx) + R2(idx)), R2(idx))
-
-#define mV_to_regval(mV) DIV_ROUND(((((mV) < 4125) ? 4125 : (mV)) - 4125), 125)
-#define regval_to_mV(v) (((v) * 125 + 4125))
-
-static struct ltc3673_regs {
- u8 addr;
- u8 val;
- u8 mask;
-} ltc3676_regs[] = {
- { LTC3676_MSKPG, ~LTC3676_MSKPG_BUCK1, },
- { LTC3676_DVB2B, VDD_SOC_VAL_LP | LTC3676_PGOOD_MASK, ~0x3f, },
- { LTC3676_DVB3B, VDD_DDR_VAL_LP, ~0x3f, },
- { LTC3676_DVB4B, VDD_CORE_VAL_LP | LTC3676_PGOOD_MASK, ~0x3f, },
- { LTC3676_DVB2A, VDD_SOC_VAL, ~0x3f, },
- { LTC3676_DVB3A, VDD_DDR_VAL, ~0x3f, },
- { LTC3676_DVB4A, VDD_CORE_VAL, ~0x3f, },
- { LTC3676_BUCK1, LTC3676_BUCK_BURST_MODE | LTC3676_BUCK_CLK_RATE_LOW, },
- { LTC3676_BUCK2, LTC3676_BUCK_BURST_MODE, },
- { LTC3676_BUCK3, LTC3676_BUCK_BURST_MODE, },
- { LTC3676_BUCK4, LTC3676_BUCK_BURST_MODE, },
- { LTC3676_CLIRQ, 0, }, /* clear interrupt status */
-};
-static struct ltc3673_regs ltc3676_regs_2[] = {
- { LTC3676_DVB1B, VDD_IO_VAL_2_LP | LTC3676_PGOOD_MASK, ~0x3f, },
- { LTC3676_DVB1A, VDD_IO_VAL_2, ~0x3f, },
-};
+static void eth_init(void)
+{
+ void __iomem *iomux = (void *)MX6_IOMUXC_BASE_ADDR;
+ uint32_t val;
+
+ val = readl(iomux + IOMUXC_GPR1);
+ val |= IMX6Q_GPR1_ENET_CLK_SEL_ANATOP;
+ writel(val, iomux + IOMUXC_GPR1);
+}
+static struct {
+ unsigned char addr;
+ int (*init)(struct i2c_client *client);
+ const char *name;
+} i2c_addrs[] = {
+ { 0x3c, ltc3676_pmic_setup, "ltc3676" },
+ { 0x32, rn5t618_pmic_setup, "rn5t618" },
+ { 0x33, rn5t567_pmic_setup, "rn5t567" },
+};
-static int setup_pmic_voltages(void)
+int setup_pmic_voltages(void)
{
- struct i2c_adapter *adapter = NULL;
+ struct i2c_adapter *adapter;
struct i2c_client client;
- int addr = 0x3c;
- int bus = 0;
+ int ret = -ENODEV;
int i;
- struct ltc3673_regs *r;
+ int bus = 0;
+ uint8_t reg;
adapter = i2c_get_adapter(bus);
if (!adapter) {
@@ -150,37 +68,26 @@ static int setup_pmic_voltages(void)
}
client.adapter = adapter;
- client.addr = addr;
- r = ltc3676_regs;
+ for (i = 0; i < ARRAY_SIZE(i2c_addrs); i++) {
+ client.addr = i2c_addrs[i].addr;
- for (i = 0; i < ARRAY_SIZE(ltc3676_regs); i++, r++) {
- if (i2c_write_reg(&client, r->addr, &r->val, 1) != 1) {
- pr_err("i2c write error\n");
- return -EIO;
- }
- }
+ pr_debug("Probing for I2C dev 0x%02x\n", client.addr);
- r = ltc3676_regs_2;
-
- for (i = 0; i < ARRAY_SIZE(ltc3676_regs_2); i++, r++) {
- if (i2c_write_reg(&client, r->addr, &r->val, 1) != 1) {
- pr_err("i2c write error\n");
- return -EIO;
+ ret = i2c_write_reg(&client, 0x00, ®, 0);
+ if (ret == 0) {
+ pr_info("Detected %s PMIC\n", i2c_addrs[i].name);
+ ret = i2c_addrs[i].init(&client);
+ goto out;
}
}
- return 0;
-}
+ pr_err("No PMIC found\n");
+out:
+ if (ret)
+ pr_err("PMIC setup failed with %s\n", strerror(-ret));
-static void eth_init(void)
-{
- void __iomem *iomux = (void *)MX6_IOMUXC_BASE_ADDR;
- uint32_t val;
-
- val = readl(iomux + IOMUXC_GPR1);
- val |= IMX6Q_GPR1_ENET_CLK_SEL_ANATOP;
- writel(val, iomux + IOMUXC_GPR1);
+ return ret;
}
#define IMX6_SRC_SBMR1 0x04
diff --git a/arch/arm/boards/karo-tx6x/pmic-ltc3676.c b/arch/arm/boards/karo-tx6x/pmic-ltc3676.c
new file mode 100644
index 0000000..0cddb92
--- /dev/null
+++ b/arch/arm/boards/karo-tx6x/pmic-ltc3676.c
@@ -0,0 +1,149 @@
+/*
+ * Copyright (C) 2014 Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <i2c/i2c.h>
+#include "pmic.h"
+
+#define LTC3676_BUCK1 0x01
+#define LTC3676_BUCK2 0x02
+#define LTC3676_BUCK3 0x03
+#define LTC3676_BUCK4 0x04
+#define LTC3676_DVB1A 0x0A
+#define LTC3676_DVB1B 0x0B
+#define LTC3676_DVB2A 0x0C
+#define LTC3676_DVB2B 0x0D
+#define LTC3676_DVB3A 0x0E
+#define LTC3676_DVB3B 0x0F
+#define LTC3676_DVB4A 0x10
+#define LTC3676_DVB4B 0x11
+#define LTC3676_MSKPG 0x13
+#define LTC3676_CLIRQ 0x1f
+
+#define LTC3676_BUCK_DVDT_FAST (1 << 0)
+#define LTC3676_BUCK_KEEP_ALIVE (1 << 1)
+#define LTC3676_BUCK_CLK_RATE_LOW (1 << 2)
+#define LTC3676_BUCK_PHASE_SEL (1 << 3)
+#define LTC3676_BUCK_ENABLE_300 (1 << 4)
+#define LTC3676_BUCK_PULSE_SKIP (0 << 5)
+#define LTC3676_BUCK_BURST_MODE (1 << 5)
+#define LTC3676_BUCK_CONTINUOUS (2 << 5)
+#define LTC3676_BUCK_ENABLE (1 << 7)
+
+#define LTC3676_PGOOD_MASK (1 << 5)
+
+#define LTC3676_MSKPG_BUCK1 (1 << 0)
+#define LTC3676_MSKPG_BUCK2 (1 << 1)
+#define LTC3676_MSKPG_BUCK3 (1 << 2)
+#define LTC3676_MSKPG_BUCK4 (1 << 3)
+#define LTC3676_MSKPG_LDO2 (1 << 5)
+#define LTC3676_MSKPG_LDO3 (1 << 6)
+#define LTC3676_MSKPG_LDO4 (1 << 7)
+
+#define VDD_IO_VAL mV_to_regval(vout_to_vref(3300 * 10, 5))
+#define VDD_IO_VAL_LP mV_to_regval(vout_to_vref(3100 * 10, 5))
+#define VDD_IO_VAL_2 mV_to_regval(vout_to_vref(3300 * 10, 5_2))
+#define VDD_IO_VAL_2_LP mV_to_regval(vout_to_vref(3100 * 10, 5_2))
+#define VDD_SOC_VAL mV_to_regval(vout_to_vref(1425 * 10, 6))
+#define VDD_SOC_VAL_LP mV_to_regval(vout_to_vref(900 * 10, 6))
+#define VDD_DDR_VAL mV_to_regval(vout_to_vref(1500 * 10, 7))
+#define VDD_DDR_VAL_LP mV_to_regval(vout_to_vref(1500 * 10, 7))
+#define VDD_CORE_VAL mV_to_regval(vout_to_vref(1425 * 10, 8))
+#define VDD_CORE_VAL_LP mV_to_regval(vout_to_vref(900 * 10, 8))
+
+/* LDO1 */
+#define R1_1 470
+#define R2_1 150
+/* LDO4 */
+#define R1_4 470
+#define R2_4 150
+/* Buck1 */
+#define R1_5 390
+#define R2_5 110
+#define R1_5_2 470
+#define R2_5_2 150
+/* Buck2 (SOC) */
+#define R1_6 150
+#define R2_6 180
+/* Buck3 (DDR) */
+#define R1_7 150
+#define R2_7 140
+/* Buck4 (CORE) */
+#define R1_8 150
+#define R2_8 180
+
+/* calculate voltages in 10mV */
+#define R1(idx) R1_##idx
+#define R2(idx) R2_##idx
+
+#define vout_to_vref(vout, idx) ((vout) * R2(idx) / (R1(idx) + R2(idx)))
+#define vref_to_vout(vref, idx) DIV_ROUND_UP((vref) * (R1(idx) + R2(idx)), R2(idx))
+
+#define mV_to_regval(mV) DIV_ROUND(((((mV) < 4125) ? 4125 : (mV)) - 4125), 125)
+#define regval_to_mV(v) (((v) * 125 + 4125))
+
+static struct ltc3673_regs {
+ u8 addr;
+ u8 val;
+ u8 mask;
+} ltc3676_regs[] = {
+ { LTC3676_MSKPG, ~LTC3676_MSKPG_BUCK1, },
+ { LTC3676_DVB2B, VDD_SOC_VAL_LP | LTC3676_PGOOD_MASK, ~0x3f, },
+ { LTC3676_DVB3B, VDD_DDR_VAL_LP, ~0x3f, },
+ { LTC3676_DVB4B, VDD_CORE_VAL_LP | LTC3676_PGOOD_MASK, ~0x3f, },
+ { LTC3676_DVB2A, VDD_SOC_VAL, ~0x3f, },
+ { LTC3676_DVB3A, VDD_DDR_VAL, ~0x3f, },
+ { LTC3676_DVB4A, VDD_CORE_VAL, ~0x3f, },
+ { LTC3676_BUCK1, LTC3676_BUCK_BURST_MODE | LTC3676_BUCK_CLK_RATE_LOW, },
+ { LTC3676_BUCK2, LTC3676_BUCK_BURST_MODE, },
+ { LTC3676_BUCK3, LTC3676_BUCK_BURST_MODE, },
+ { LTC3676_BUCK4, LTC3676_BUCK_BURST_MODE, },
+ { LTC3676_CLIRQ, 0, }, /* clear interrupt status */
+};
+
+static struct ltc3673_regs ltc3676_regs_2[] = {
+ { LTC3676_DVB1B, VDD_IO_VAL_2_LP | LTC3676_PGOOD_MASK, ~0x3f, },
+ { LTC3676_DVB1A, VDD_IO_VAL_2, ~0x3f, },
+};
+
+
+int ltc3676_pmic_setup(struct i2c_client *client)
+{
+ int i;
+ struct ltc3673_regs *r;
+
+ r = ltc3676_regs;
+
+ for (i = 0; i < ARRAY_SIZE(ltc3676_regs); i++, r++) {
+ if (i2c_write_reg(client, r->addr, &r->val, 1) != 1) {
+ pr_err("i2c write error\n");
+ return -EIO;
+ }
+ }
+
+ r = ltc3676_regs_2;
+
+ for (i = 0; i < ARRAY_SIZE(ltc3676_regs_2); i++, r++) {
+ if (i2c_write_reg(client, r->addr, &r->val, 1) != 1) {
+ pr_err("i2c write error\n");
+ return -EIO;
+ }
+ }
+
+ return 0;
+}
+
diff --git a/arch/arm/boards/karo-tx6x/pmic-rn5t567.c b/arch/arm/boards/karo-tx6x/pmic-rn5t567.c
new file mode 100644
index 0000000..363ffbc
--- /dev/null
+++ b/arch/arm/boards/karo-tx6x/pmic-rn5t567.c
@@ -0,0 +1,154 @@
+/*
+ * Copyright (C) 2014 Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <i2c/i2c.h>
+#include "pmic.h"
+
+#define RN5T567_NOETIMSET 0x11
+#define RN5T567_LDORTC1_SLOT 0x2a
+#define RN5T567_DC1CTL 0x2c
+#define RN5T567_DC1CTL2 0x2d
+#define RN5T567_DC2CTL 0x2e
+#define RN5T567_DC2CTL2 0x2f
+#define RN5T567_DC3CTL 0x30
+#define RN5T567_DC3CTL2 0x31
+#define RN5T567_DC1DAC 0x36 /* CORE */
+#define RN5T567_DC2DAC 0x37 /* SOC */
+#define RN5T567_DC3DAC 0x38 /* DDR */
+#define RN5T567_DC1DAC_SLP 0x3b
+#define RN5T567_DC2DAC_SLP 0x3c
+#define RN5T567_DC3DAC_SLP 0x3d
+#define RN5T567_LDOEN1 0x44
+#define RN5T567_LDODIS 0x46
+#define RN5T567_LDOEN2 0x48
+#define RN5T567_LDO3DAC 0x4e /* IO */
+#define RN5T567_LDORTC1DAC 0x56 /* VBACKUP */
+
+#define NOETIMSET_DIS_OFF_NOE_TIM (1 << 3)
+
+#define VDD_RTC_VAL mV_to_regval_rtc(3000)
+#define VDD_HIGH_VAL mV_to_regval3(3000)
+#define VDD_HIGH_VAL_LP mV_to_regval3(3000)
+#define VDD_CORE_VAL mV_to_regval(1350) /* DCDC1 */
+#define VDD_CORE_VAL_LP mV_to_regval(900)
+#define VDD_SOC_VAL mV_to_regval(1350) /* DCDC2 */
+#define VDD_SOC_VAL_LP mV_to_regval(900)
+#define VDD_DDR_VAL mV_to_regval(1350) /* DCDC3 */
+#define VDD_DDR_VAL_LP mV_to_regval(1350)
+
+/* calculate voltages in 10mV */
+#define v2r(v,n,m) DIV_ROUND(((((v) < (n)) ? (n) : (v)) - (n)), (m))
+#define r2v(r,n,m) (((r) * (m) + (n)) / 10)
+
+/* DCDC1-3 */
+#define mV_to_regval(mV) v2r((mV) * 10, 6000, 125)
+#define regval_to_mV(r) r2v(r, 6000, 125)
+
+/* LDO1-2 */
+#define mV_to_regval2(mV) v2r((mV) * 10, 9000, 250)
+#define regval2_to_mV(r) r2v(r, 9000, 250)
+
+/* LDO3 */
+#define mV_to_regval3(mV) v2r((mV) * 10, 6000, 250)
+#define regval3_to_mV(r) r2v(r, 6000, 250)
+
+/* LDORTC */
+#define mV_to_regval_rtc(mV) v2r((mV) * 10, 17000, 250)
+#define regval_rtc_to_mV(r) r2v(r, 17000, 250)
+
+static struct rn5t567_regs {
+ u8 addr;
+ u8 val;
+ u8 mask;
+} rn5t567_regs[] = {
+ { RN5T567_NOETIMSET, NOETIMSET_DIS_OFF_NOE_TIM | 0x5, },
+ { RN5T567_DC1DAC, VDD_CORE_VAL, },
+ { RN5T567_DC2DAC, VDD_SOC_VAL, },
+ { RN5T567_DC3DAC, VDD_DDR_VAL, },
+ { RN5T567_DC1DAC_SLP, VDD_CORE_VAL_LP, },
+ { RN5T567_DC2DAC_SLP, VDD_SOC_VAL_LP, },
+ { RN5T567_DC3DAC_SLP, VDD_DDR_VAL_LP, },
+ { RN5T567_LDOEN1, 0x01f, ~0x1f, },
+ { RN5T567_LDOEN2, 0x10, ~0x30, },
+ { RN5T567_LDODIS, 0x00, },
+ { RN5T567_LDO3DAC, VDD_HIGH_VAL, },
+ { RN5T567_LDORTC1DAC, VDD_RTC_VAL, },
+ { RN5T567_LDORTC1_SLOT, 0x0f, ~0x3f, },
+};
+
+static int rn5t567_setup_regs(struct i2c_client *client, struct rn5t567_regs *r,
+ size_t count)
+{
+ int ret;
+ int i;
+
+ for (i = 0; i < count; i++, r++) {
+#ifdef DEBUG
+ unsigned char value;
+
+ ret = i2c_read_reg(client, r->addr, &value, 1);
+ if ((value & ~r->mask) != r->val) {
+ pr_debug("Changing PMIC reg %02x from %02x to %02x\n",
+ r->addr, value, r->val);
+ }
+ if (ret != 1) {
+ pr_debug("%s: failed to read PMIC register %02x: %d\n",
+ __func__, r->addr, ret);
+ return ret;
+ }
+#endif
+ ret = i2c_write_reg(client, r->addr, &r->val, 1);
+ if (ret != 1) {
+ pr_err("%s: failed to write PMIC register %02x: %d\n",
+ __func__, r->addr, ret);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+int rn5t567_pmic_setup(struct i2c_client *client)
+{
+ int ret;
+ unsigned char value;
+
+ ret = i2c_read_reg(client, 0x11, &value, 1);
+ if (ret != 1) {
+ pr_err("i2c read error\n");
+ return ret;
+ }
+
+ ret = rn5t567_setup_regs(client, rn5t567_regs,
+ ARRAY_SIZE(rn5t567_regs));
+ if (ret)
+ return ret;
+
+ ret = i2c_read_reg(client, RN5T567_DC1DAC, &value, 1);
+ if (ret == 1)
+ pr_debug("VDDCORE set to %umV\n", regval_to_mV(value));
+ else
+ pr_err("i2c read error\n");
+
+ ret = i2c_read_reg(client, RN5T567_DC2DAC, &value, 1);
+ if (ret == 1)
+ pr_debug("VDDSOC set to %umV\n", regval_to_mV(value));
+ else
+ pr_err("i2c read error\n");
+
+ return ret;
+}
diff --git a/arch/arm/boards/karo-tx6x/pmic-rn5t618.c b/arch/arm/boards/karo-tx6x/pmic-rn5t618.c
new file mode 100644
index 0000000..7c722c2
--- /dev/null
+++ b/arch/arm/boards/karo-tx6x/pmic-rn5t618.c
@@ -0,0 +1,152 @@
+/*
+ * Copyright (C) 2014 Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <i2c/i2c.h>
+#include "pmic.h"
+
+#define RN5T618_NOETIMSET 0x11
+#define RN5T618_LDORTC1_SLOT 0x2a
+#define RN5T618_DC1CTL 0x2c
+#define RN5T618_DC1CTL2 0x2d
+#define RN5T618_DC2CTL 0x2e
+#define RN5T618_DC2CTL2 0x2f
+#define RN5T618_DC3CTL 0x30
+#define RN5T618_DC3CTL2 0x31
+#define RN5T618_DC1DAC 0x36 /* CORE */
+#define RN5T618_DC2DAC 0x37 /* SOC */
+#define RN5T618_DC3DAC 0x38 /* DDR */
+#define RN5T618_DC1DAC_SLP 0x3b
+#define RN5T618_DC2DAC_SLP 0x3c
+#define RN5T618_DC3DAC_SLP 0x3d
+#define RN5T618_LDOEN1 0x44
+#define RN5T618_LDODIS 0x46
+#define RN5T618_LDOEN2 0x48
+#define RN5T618_LDO3DAC 0x4e /* IO */
+#define RN5T618_LDORTCDAC 0x56 /* VBACKUP */
+
+#define VDD_RTC_VAL mV_to_regval_rtc(3000)
+#define VDD_HIGH_VAL mV_to_regval3(3000)
+#define VDD_HIGH_VAL_LP mV_to_regval3(3000)
+#define VDD_CORE_VAL mV_to_regval(1425) /* DCDC1 */
+#define VDD_CORE_VAL_LP mV_to_regval(900)
+#define VDD_SOC_VAL mV_to_regval(1425) /* DCDC2 */
+#define VDD_SOC_VAL_LP mV_to_regval(900)
+#define VDD_DDR_VAL mV_to_regval(1500) /* DCDC3 */
+#define VDD_DDR_VAL_LP mV_to_regval(1500)
+
+/* calculate voltages in 10mV */
+#define v2r(v,n,m) DIV_ROUND(((((v) < (n)) ? (n) : (v)) - (n)), (m))
+#define r2v(r,n,m) (((r) * (m) + (n)) / 10)
+
+/* DCDC1-3 */
+#define mV_to_regval(mV) v2r((mV) * 10, 6000, 125)
+#define regval_to_mV(r) r2v(r, 6000, 125)
+
+/* LDO1-2 */
+#define mV_to_regval2(mV) v2r((mV) * 10, 9000, 250)
+#define regval2_to_mV(r) r2v(r, 9000, 250)
+
+/* LDO3 */
+#define mV_to_regval3(mV) v2r((mV) * 10, 6000, 250)
+#define regval3_to_mV(r) r2v(r, 6000, 250)
+
+/* LDORTC */
+#define mV_to_regval_rtc(mV) v2r((mV) * 10, 17000, 250)
+#define regval_rtc_to_mV(r) r2v(r, 17000, 250)
+
+static struct rn5t618_regs {
+ u8 addr;
+ u8 val;
+ u8 mask;
+} rn5t618_regs[] = {
+ { RN5T618_NOETIMSET, 0, },
+ { RN5T618_DC1DAC, VDD_CORE_VAL, },
+ { RN5T618_DC2DAC, VDD_SOC_VAL, },
+ { RN5T618_DC3DAC, VDD_DDR_VAL, },
+ { RN5T618_DC1DAC_SLP, VDD_CORE_VAL_LP, },
+ { RN5T618_DC2DAC_SLP, VDD_SOC_VAL_LP, },
+ { RN5T618_DC3DAC_SLP, VDD_DDR_VAL_LP, },
+ { RN5T618_LDOEN1, 0x01f, ~0x1f, },
+ { RN5T618_LDOEN2, 0x10, ~0x30, },
+ { RN5T618_LDODIS, 0x00, },
+ { RN5T618_LDO3DAC, VDD_HIGH_VAL, },
+ { RN5T618_LDORTCDAC, VDD_RTC_VAL, },
+ { RN5T618_LDORTC1_SLOT, 0x0f, ~0x3f, },
+};
+
+static int rn5t618_setup_regs(struct i2c_client *client, struct rn5t618_regs *r,
+ size_t count)
+{
+ int ret;
+ int i;
+
+ for (i = 0; i < count; i++, r++) {
+#ifdef DEBUG
+ unsigned char value;
+
+ ret = i2c_read_reg(client, r->addr, &value, 1);
+ if ((value & ~r->mask) != r->val) {
+ pr_debug("Changing PMIC reg %02x from %02x to %02x\n",
+ r->addr, value, r->val);
+ }
+ if (ret != 1) {
+ pr_debug("%s: failed to read PMIC register %02x: %d\n",
+ __func__, r->addr, ret);
+ return ret;
+ }
+#endif
+ ret = i2c_write_reg(client, r->addr, &r->val, 1);
+ if (ret != 1) {
+ pr_err("%s: failed to write PMIC register %02x: %d\n",
+ __func__, r->addr, ret);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+int rn5t618_pmic_setup(struct i2c_client *client)
+{
+ int ret;
+ unsigned char value;
+
+ ret = i2c_read_reg(client, 0x11, &value, 1);
+ if (ret) {
+ pr_err("i2c read error\n");
+ return ret;
+ }
+
+ ret = rn5t618_setup_regs(client, rn5t618_regs,
+ ARRAY_SIZE(rn5t618_regs));
+ if (ret)
+ return ret;
+
+ ret = i2c_read_reg(client, RN5T618_DC1DAC, &value, 1);
+ if (ret == 1)
+ pr_debug("VDDCORE set to %umV\n", regval_to_mV(value));
+ else
+ pr_err("i2c read error\n");
+
+ ret = i2c_read_reg(client, RN5T618_DC2DAC, &value, 1);
+ if (ret == 1)
+ pr_debug("VDDSOC set to %umV\n", regval_to_mV(value));
+ else
+ pr_err("i2c read error\n");
+
+ return ret;
+}
diff --git a/arch/arm/boards/karo-tx6x/pmic.h b/arch/arm/boards/karo-tx6x/pmic.h
new file mode 100644
index 0000000..2427a52
--- /dev/null
+++ b/arch/arm/boards/karo-tx6x/pmic.h
@@ -0,0 +1,8 @@
+
+#include <i2c/i2c.h>
+
+#define DIV_ROUND(n,d) (((n) + ((d)/2)) / (d))
+
+int ltc3676_pmic_setup(struct i2c_client *client);
+int rn5t567_pmic_setup(struct i2c_client *client);
+int rn5t618_pmic_setup(struct i2c_client *client);
--
2.7.0
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
