Add a driver for DesignWare I2C controller IP block found on several
SoCs including Altera SoC products
Tested using Terrasic SoCKit board and GPIO expander board with I2C
EEPROM on it
Signed-off-by: Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
---
drivers/i2c/busses/Kconfig | 6 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-designware.c | 576 ++++++++++++++++++++++++++++++++++++
3 files changed, 583 insertions(+)
create mode 100644 drivers/i2c/busses/i2c-designware.c
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 181321b..a25a871 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -25,6 +25,12 @@ config I2C_IMX
for many i.MX ARM based SoCs, for MPC85xx and MPC5200 PowerPC based
SoCs.
+config I2C_DESIGNWARE
+ bool "Synopsys DesignWare I2C Master driver"
+ help
+ If you say yes to this option, support will be included for the
+ Synopsys DesignWare I2C adapter. Only master mode is supported.
+
config I2C_MV64XXX
bool "Marvell mv64xxx I2C Controller"
depends on HAVE_CLK && OFDEVICE
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 1dbfbdf..8dccc38 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_I2C_MV64XXX) += i2c-mv64xxx.o
obj-$(CONFIG_I2C_OMAP) += i2c-omap.o
obj-$(CONFIG_I2C_TEGRA) += i2c-tegra.o
obj-$(CONFIG_I2C_VERSATILE) += i2c-versatile.o
+obj-$(CONFIG_I2C_DESIGNWARE) += i2c-designware.o
diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c
new file mode 100644
index 0000000..333d312
--- /dev/null
+++ b/drivers/i2c/busses/i2c-designware.c
@@ -0,0 +1,576 @@
+/*
+ * Synopsys DesignWare I2C adapter driver (master only).
+ *
+ * Partly based on code of similar driver from U-Boot:
+ * Copyright (C) 2009 ST Micoelectronics
+ *
+ * and corresponding code from Linux Kernel
+ * Copyright (C) 2006 Texas Instruments.
+ * Copyright (C) 2007 MontaVista Software Inc.
+ * Copyright (C) 2009 Provigent Ltd.
+ *
+ * Copyright (C) 2014 Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <clock.h>
+#include <common.h>
+#include <driver.h>
+#include <init.h>
+#include <of.h>
+#include <malloc.h>
+#include <types.h>
+#include <xfuncs.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+
+#include <io.h>
+#include <i2c/i2c.h>
+
+#define DW_I2C_BIT_RATE 100000
+
+#define DW_IC_CON 0x0
+#define DW_IC_CON_MASTER (1 << 0)
+#define DW_IC_CON_SPEED_STD (1 << 1)
+#define DW_IC_CON_SPEED_FAST (1 << 2)
+#define DW_IC_CON_SLAVE_DISABLE (1 << 6)
+
+#define DW_IC_TAR 0x4
+
+#define DW_IC_DATA_CMD 0x10
+#define DW_IC_DATA_CMD_CMD (1 << 8)
+#define DW_IC_DATA_CMD_STOP (1 << 9)
+
+#define DW_IC_SS_SCL_HCNT 0x14
+#define DW_IC_SS_SCL_LCNT 0x18
+#define DW_IC_FS_SCL_HCNT 0x1c
+#define DW_IC_FS_SCL_LCNT 0x20
+
+#define DW_IC_INTR_MASK 0x30
+
+#define DW_IC_RAW_INTR_STAT 0x34
+#define DW_IC_INTR_RX_UNDER (1 << 0)
+#define DW_IC_INTR_RX_OVER (1 << 1)
+#define DW_IC_INTR_RX_FULL (1 << 2)
+#define DW_IC_INTR_TX_OVER (1 << 3)
+#define DW_IC_INTR_TX_EMPTY (1 << 4)
+#define DW_IC_INTR_RD_REQ (1 << 5)
+#define DW_IC_INTR_TX_ABRT (1 << 6)
+#define DW_IC_INTR_RX_DONE (1 << 7)
+#define DW_IC_INTR_ACTIVITY (1 << 8)
+#define DW_IC_INTR_STOP_DET (1 << 9)
+#define DW_IC_INTR_START_DET (1 << 10)
+#define DW_IC_INTR_GEN_CALL (1 << 11)
+
+#define DW_IC_RX_TL 0x38
+#define DW_IC_TX_TL 0x3c
+#define DW_IC_CLR_INTR 0x40
+#define DW_IC_CLR_TX_ABRT 0x54
+
+#define DW_IC_ENABLE 0x6c
+#define DW_IC_ENABLE_ENABLE (1 << 0)
+
+#define DW_IC_STATUS 0x70
+#define DW_IC_STATUS_TFNF (1 << 1)
+#define DW_IC_STATUS_TFE (1 << 2)
+#define DW_IC_STATUS_RFNE (1 << 3)
+#define DW_IC_STATUS_MST_ACTIVITY (1 << 5)
+
+#define DW_IC_TX_ABRT_SOURCE 0x80
+
+#define DW_IC_ENABLE_STATUS 0x9c
+#define DW_IC_ENABLE_STATUS_IC_EN (1 << 0)
+
+#define DW_IC_COMP_TYPE 0xfc
+#define DW_IC_COMP_TYPE_VALUE 0x44570140
+
+#define MAX_T_POLL_COUNT 100
+
+#define DW_TIMEOUT_IDLE (40 * MSECOND)
+#define DW_TIMEOUT_TX (2 * MSECOND)
+#define DW_TIMEOUT_RX (2 * MSECOND)
+
+struct dw_i2c_dev {
+ void __iomem *base;
+ struct clk *clk;
+ struct i2c_adapter adapter;
+};
+
+static inline struct dw_i2c_dev *to_dw_i2c_dev(struct i2c_adapter *a)
+{
+ return container_of(a, struct dw_i2c_dev, adapter);
+}
+
+static void i2c_dw_enable(struct dw_i2c_dev *dw, bool enable)
+{
+ /*
+ * This subrotine is an implementation of an algorithm
+ * described in "Cyclone V Hard Processor System Technical
+ * Reference * Manual" p. 20-19, "Disabling the I2C Controller"
+ */
+ int timeout = MAX_T_POLL_COUNT;
+
+ enable = enable ? DW_IC_ENABLE_ENABLE : 0;
+
+ do {
+ uint32_t ic_enable_status;
+
+ writel(enable, dw->base + DW_IC_ENABLE);
+
+ ic_enable_status = readl(dw->base + DW_IC_ENABLE_STATUS);
+ if ((ic_enable_status & DW_IC_ENABLE_STATUS_IC_EN) == enable)
+ return;
+
+ udelay(250);
+ } while (timeout--);
+
+ dev_warn(&dw->adapter.dev, "timeout in %sabling adapter\n",
+ enable ? "en" : "dis");
+}
+
+/*
+ * All of the code pertaining to tming calculation is taken from
+ * analogous driver in Linux kernel
+ */
+static uint32_t
+i2c_dw_scl_hcnt(uint32_t ic_clk, uint32_t tSYMBOL, uint32_t tf, int cond,
+ int offset)
+{
+ /*
+ * DesignWare I2C core doesn't seem to have solid strategy to meet
+ * the tHD;STA timing spec. Configuring _HCNT based on tHIGH spec
+ * will result in violation of the tHD;STA spec.
+ */
+ if (cond)
+ /*
+ * Conditional expression:
+ *
+ * IC_[FS]S_SCL_HCNT + (1+4+3) >= IC_CLK * tHIGH
+ *
+ * This is based on the DW manuals, and represents an ideal
+ * configuration. The resulting I2C bus speed will be
+ * faster than any of the others.
+ *
+ * If your hardware is free from tHD;STA issue, try this one.
+ */
+ return (ic_clk * tSYMBOL + 500000) / 1000000 - 8 + offset;
+ else
+ /*
+ * Conditional expression:
+ *
+ * IC_[FS]S_SCL_HCNT + 3 >= IC_CLK * (tHD;STA + tf)
+ *
+ * This is just experimental rule; the tHD;STA period turned
+ * out to be proportinal to (_HCNT + 3). With this setting,
+ * we could meet both tHIGH and tHD;STA timing specs.
+ *
+ * If unsure, you'd better to take this alternative.
+ *
+ * The reason why we need to take into account "tf" here,
+ * is the same as described in i2c_dw_scl_lcnt().
+ */
+ return (ic_clk * (tSYMBOL + tf) + 500000) / 1000000
+ - 3 + offset;
+}
+
+static uint32_t
+i2c_dw_scl_lcnt(uint32_t ic_clk, uint32_t tLOW, uint32_t tf, int offset)
+{
+ /*
+ * Conditional expression:
+ *
+ * IC_[FS]S_SCL_LCNT + 1 >= IC_CLK * (tLOW + tf)
+ *
+ * DW I2C core starts counting the SCL CNTs for the LOW period
+ * of the SCL clock (tLOW) as soon as it pulls the SCL line.
+ * In order to meet the tLOW timing spec, we need to take into
+ * account the fall time of SCL signal (tf). Default tf value
+ * should be 0.3 us, for safety.
+ */
+ return ((ic_clk * (tLOW + tf) + 500000) / 1000000) - 1 + offset;
+}
+
+static void i2c_dw_setup_timings(struct dw_i2c_dev *dw)
+{
+ uint32_t hcnt, lcnt;
+
+ const uint32_t sda_falling_time = 300; /* ns */
+ const uint32_t scl_falling_time = 300; /* ns */
+
+ const unsigned int input_clock_khz = clk_get_rate(dw->clk) / 1000;
+
+ /* Set SCL timing parameters for standard-mode */
+ hcnt = i2c_dw_scl_hcnt(input_clock_khz,
+ 4000, /* tHD;STA = tHIGH = 4.0 us */
+ sda_falling_time,
+ 0, /* 0: DW default, 1: Ideal */
+ 0); /* No offset */
+ lcnt = i2c_dw_scl_lcnt(input_clock_khz,
+ 4700, /* tLOW = 4.7 us */
+ scl_falling_time,
+ 0); /* No offset */
+
+ writel(hcnt, dw->base + DW_IC_SS_SCL_HCNT);
+ writel(lcnt, dw->base + DW_IC_SS_SCL_LCNT);
+
+ hcnt = i2c_dw_scl_hcnt(input_clock_khz,
+ 600, /* tHD;STA = tHIGH = 0.6 us */
+ sda_falling_time,
+ 0, /* 0: DW default, 1: Ideal */
+ 0); /* No offset */
+ lcnt = i2c_dw_scl_lcnt(input_clock_khz,
+ 1300, /* tLOW = 1.3 us */
+ scl_falling_time,
+ 0); /* No offset */
+
+ writel(hcnt, dw->base + DW_IC_FS_SCL_HCNT);
+ writel(lcnt, dw->base + DW_IC_FS_SCL_LCNT);
+}
+
+static int i2c_dw_wait_for_bits(struct dw_i2c_dev *dw, uint32_t offset,
+ uint32_t mask, uint32_t value, uint64_t timeout)
+{
+ const uint64_t start = get_time_ns();
+
+ do {
+ const uint32_t reg = readl(dw->base + offset);
+
+ if ((reg & mask) == value)
+ return 0;
+
+ } while (!is_timeout(start, timeout));
+
+ return -ETIMEDOUT;
+}
+
+static int i2c_dw_wait_for_idle(struct dw_i2c_dev *dw)
+{
+ const uint32_t mask = DW_IC_STATUS_MST_ACTIVITY | DW_IC_STATUS_TFE;
+ const uint32_t value = DW_IC_STATUS_TFE;
+
+ return i2c_dw_wait_for_bits(dw, DW_IC_STATUS, mask, value,
+ DW_TIMEOUT_IDLE);
+}
+
+static int i2c_dw_wait_for_tx_fifo_not_full(struct dw_i2c_dev *dw)
+{
+ const uint32_t mask = DW_IC_STATUS_TFNF;
+ const uint32_t value = DW_IC_STATUS_TFNF;
+
+ return i2c_dw_wait_for_bits(dw, DW_IC_STATUS, mask, value,
+ DW_TIMEOUT_TX);
+}
+
+static int i2c_dw_wait_for_rx_fifo_not_empty(struct dw_i2c_dev *dw)
+{
+ const uint32_t mask = DW_IC_STATUS_RFNE;
+ const uint32_t value = DW_IC_STATUS_RFNE;
+
+ return i2c_dw_wait_for_bits(dw, DW_IC_STATUS, mask, value,
+ DW_TIMEOUT_RX);
+}
+
+static void i2c_dw_reset(struct dw_i2c_dev *dw)
+{
+ i2c_dw_enable(dw, false);
+ i2c_dw_enable(dw, true);
+}
+
+static void i2c_dw_abort_tx(struct dw_i2c_dev *dw)
+{
+ i2c_dw_reset(dw);
+}
+
+static void i2c_dw_abort_rx(struct dw_i2c_dev *dw)
+{
+ i2c_dw_reset(dw);
+}
+
+static int i2c_dw_read(struct dw_i2c_dev *dw,
+ const struct i2c_msg *msg)
+{
+ int i;
+ for (i = 0; i < msg->len; i++) {
+ int ret;
+ const bool last_byte = i == msg->len - 1;
+ uint32_t ic_cmd_data = DW_IC_DATA_CMD_CMD;
+
+ if (last_byte)
+ ic_cmd_data |= DW_IC_DATA_CMD_STOP;
+
+ writel(ic_cmd_data, dw->base + DW_IC_DATA_CMD);
+
+ ret = i2c_dw_wait_for_rx_fifo_not_empty(dw);
+ if (ret < 0) {
+ i2c_dw_abort_rx(dw);
+ return ret;
+ }
+
+ msg->buf[i] = (uint8_t)readl(dw->base + DW_IC_DATA_CMD);
+ }
+
+ return msg->len;
+}
+
+static int i2c_dw_write(struct dw_i2c_dev *dw,
+ const struct i2c_msg *msg)
+{
+ int i;
+ uint32_t ic_int_stat;
+
+ for (i = 0; i < msg->len; i++) {
+ int ret;
+ uint32_t ic_cmd_data;
+ const bool last_byte = i == msg->len - 1;
+
+ ic_int_stat = readl(dw->base + DW_IC_RAW_INTR_STAT);
+
+ if (ic_int_stat & DW_IC_INTR_TX_ABRT)
+ return -EIO;
+
+ ret = i2c_dw_wait_for_tx_fifo_not_full(dw);
+ if (ret < 0) {
+ i2c_dw_abort_tx(dw);
+ return ret;
+ }
+
+ ic_cmd_data = msg->buf[i];
+
+ if (last_byte)
+ ic_cmd_data |= DW_IC_DATA_CMD_STOP;
+
+ writel(ic_cmd_data, dw->base + DW_IC_DATA_CMD);
+ }
+
+ return msg->len;
+}
+
+static int i2c_dw_wait_for_stop(struct dw_i2c_dev *dw)
+{
+ const uint32_t mask = DW_IC_INTR_STOP_DET;
+ const uint32_t value = DW_IC_INTR_STOP_DET;
+
+ return i2c_dw_wait_for_bits(dw, DW_IC_RAW_INTR_STAT, mask, value,
+ DW_TIMEOUT_IDLE);
+}
+
+static int i2c_dw_finish_xfer(struct dw_i2c_dev *dw)
+{
+ int ret;
+ uint32_t ic_int_stat;
+
+ /*
+ * We expect the controller to signal STOP condition on the
+ * bus, so we are going to wait for that first.
+ */
+ ret = i2c_dw_wait_for_stop(dw);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Now that we now that the stop condition has been signaled
+ * we need to wait for controller to go into IDLE state to
+ * make sure all of the possible error conditions on the bus
+ * have been propagated to apporpriate status
+ * registers. Experiment shows that not doing so often results
+ * in false positive "successful" transfers
+ */
+ ret = i2c_dw_wait_for_idle(dw);
+
+ if (ret >= 0) {
+ ic_int_stat = readl(dw->base + DW_IC_RAW_INTR_STAT);
+
+ if (ic_int_stat & DW_IC_INTR_TX_ABRT)
+ return -EIO;
+ }
+
+ return ret;
+}
+
+static int i2c_dw_set_address(struct dw_i2c_dev *dw, uint8_t address)
+{
+ int ret;
+ uint32_t ic_tar;
+ /*
+ * As per "Cyclone V Hard Processor System Technical Reference
+ * Manual" p. 20-19, we have to wait for controller to be in
+ * idle state in order to be able to set the address
+ * dynamically
+ */
+ ret = i2c_dw_wait_for_idle(dw);
+ if (ret < 0)
+ return ret;
+
+ ic_tar = readl(dw->base + DW_IC_TAR);
+ ic_tar &= 0xfffffc00;
+
+ writel(ic_tar | address, dw->base + DW_IC_TAR);
+
+ return 0;
+}
+
+static int i2c_dw_xfer(struct i2c_adapter *adapter,
+ struct i2c_msg *msgs, int num)
+{
+ int i, ret = 0;
+ struct dw_i2c_dev *dw = to_dw_i2c_dev(adapter);
+
+ for (i = 0; i < num; i++) {
+ if (msgs[i].flags & I2C_M_DATA_ONLY)
+ return -ENOTSUPP;
+
+ ret = i2c_dw_set_address(dw, msgs[i].addr);
+ if (ret < 0)
+ break;
+
+ if (msgs[i].flags & I2C_M_RD)
+ ret = i2c_dw_read(dw, &msgs[i]);
+ else
+ ret = i2c_dw_write(dw, &msgs[i]);
+
+ if (ret < 0)
+ break;
+
+ ret = i2c_dw_finish_xfer(dw);
+ if (ret < 0)
+ break;
+ }
+
+ if (ret == -EIO) {
+ /*
+ * If we got -EIO it means that transfer was for some
+ * reason aborted, so we should figure out the reason
+ * and take steps to clear that condition
+ */
+ const uint32_t ic_tx_abrt_source =
+ readl(dw->base + DW_IC_TX_ABRT_SOURCE);
+ dev_dbg(&dw->adapter.dev,
+ "<%s> ic_tx_abrt_source: 0x%04x\n",
+ __func__, ic_tx_abrt_source);
+ readl(dw->base + DW_IC_CLR_TX_ABRT);
+
+ return ret;
+ }
+
+ if (ret < 0) {
+ i2c_dw_reset(dw);
+ return ret;
+ }
+
+ return num;
+}
+
+
+static int i2c_dw_probe(struct device_d *pdev)
+{
+ struct dw_i2c_dev *dw;
+ struct i2c_platform_data *pdata;
+ int ret, bitrate;
+ uint32_t ic_con, ic_comp_type_value;
+
+ pdata = pdev->platform_data;
+
+ dw = kzalloc(sizeof(*dw), GFP_KERNEL);
+
+ if (IS_ENABLED(CONFIG_COMMON_CLK)) {
+ dw->clk = clk_get(pdev, NULL);
+ if (IS_ERR(dw->clk)) {
+ ret = PTR_ERR(dw->clk);
+ goto fail;
+ }
+ }
+
+ dw->adapter.master_xfer = i2c_dw_xfer;
+ dw->adapter.nr = pdev->id;
+ dw->adapter.dev.parent = pdev;
+ dw->adapter.dev.device_node = pdev->device_node;
+
+ dw->base = dev_request_mem_region(pdev, 0);
+ if (IS_ERR(dw->base)) {
+ ret = PTR_ERR(dw->base);
+ goto fail;
+ }
+
+ ic_comp_type_value = readl(dw->base + DW_IC_COMP_TYPE);
+ if (ic_comp_type_value != DW_IC_COMP_TYPE_VALUE) {
+ dev_err(pdev,
+ "unknown DesignWare IP block 0x%08x",
+ ic_comp_type_value);
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ i2c_dw_enable(dw, false);
+
+ if (IS_ENABLED(CONFIG_COMMON_CLK))
+ i2c_dw_setup_timings(dw);
+
+ bitrate = (pdata && pdata->bitrate) ? pdata->bitrate : DW_I2C_BIT_RATE;
+
+ /*
+ * We have to clear 'ic_10bitaddr_master' in 'ic_tar'
+ * register, otherwise 'ic_10bitaddr_master' in 'ic_con'
+ * wouldn't clear. We don't care about preserving the contents
+ * of that register so we set it to zero.
+ */
+ writel(0, dw->base + DW_IC_TAR);
+
+ switch (bitrate) {
+ case 400000:
+ ic_con = DW_IC_CON_SPEED_FAST;
+ break;
+ default:
+ dev_warn(pdev, "requested bitrate (%d) is not supported."
+ " Falling back to 100kHz", bitrate);
+ case 100000: /* FALLTHROUGH */
+ ic_con = DW_IC_CON_SPEED_STD;
+ break;
+ }
+
+ ic_con |= DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE;
+
+ writel(ic_con, dw->base + DW_IC_CON);
+
+ /*
+ * Since we will be working in polling mode set both
+ * thresholds to their minimum
+ */
+ writel(0, dw->base + DW_IC_RX_TL);
+ writel(0, dw->base + DW_IC_TX_TL);
+
+ /* Disable and clear all interrrupts */
+ writel(0, dw->base + DW_IC_INTR_MASK);
+ readl(dw->base + DW_IC_CLR_INTR);
+
+ i2c_dw_enable(dw, true);
+
+ ret = i2c_add_numbered_adapter(&dw->adapter);
+fail:
+ if (ret < 0) {
+ dev_err(pdev, "registration failed\n");
+ kfree(dw);
+ }
+
+ return ret;
+}
+
+static __maybe_unused struct of_device_id i2c_dw_dt_ids[] = {
+ { .compatible = "snps,designware-i2c", },
+ { /* sentinel */ }
+};
+
+static struct driver_d i2c_dw_driver = {
+ .probe = i2c_dw_probe,
+ .name = "i2c-designware",
+ .of_compatible = DRV_OF_COMPAT(i2c_dw_dt_ids),
+};
+coredevice_platform_driver(i2c_dw_driver);
--
2.1.4
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
