Use the spi-nor framework for the m25p80 driver to de-duplicate the code base
and follow along with the linux kernel version, so bugfixes or features can be
easier integrated.
Based on the Linux v4.1-rc3 version of m25p80.c.
Signed-off-by: Steffen Trumtrar <s.trumtrar@xxxxxxxxxxxxxx>
---
drivers/mtd/devices/Kconfig | 2 +-
drivers/mtd/devices/m25p80.c | 998 +++++++------------------------------------
2 files changed, 166 insertions(+), 834 deletions(-)
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 7f9c30625844..345c348c692b 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -21,7 +21,7 @@ config MTD_DATAFLASH_WRITE_VERIFY
config MTD_M25P80
tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)"
- depends on SPI
+ depends on MTD_SPI_NOR
help
This enables access to most modern SPI flash chips, used for
program and data storage. Series supported include Atmel AT26DF,
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 095a4ca0936c..c941767de94c 100644
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -25,774 +25,202 @@
#include <errno.h>
#include <linux/err.h>
#include <clock.h>
-#include <linux/math64.h>
-#include <linux/mtd/cfi.h>
#include <linux/mtd/mtd.h>
+#include <linux/mtd/spi-nor.h>
+#include <linux/mod_devicetable.h>
-/* Flash opcodes. */
-#define OPCODE_WREN 0x06 /* Write enable */
-#define OPCODE_RDSR 0x05 /* Read status register */
-#define OPCODE_WRSR 0x01 /* Write status register 1 byte */
-#define OPCODE_NORM_READ 0x03 /* Read data bytes (low frequency) */
-#define OPCODE_FAST_READ 0x0b /* Read data bytes (high frequency) */
-#define OPCODE_PP 0x02 /* Page program (up to 256 bytes) */
-#define OPCODE_BE_4K 0x20 /* Erase 4KiB block */
-#define OPCODE_BE_32K 0x52 /* Erase 32KiB block */
-#define OPCODE_CHIP_ERASE 0xc7 /* Erase whole flash chip */
-#define OPCODE_SE 0xd8 /* Sector erase (usually 64KiB) */
-#define OPCODE_RDID 0x9f /* Read JEDEC ID */
-
-/* Used for SST flashes only. */
-#define OPCODE_BP 0x02 /* Byte program */
-#define OPCODE_WRDI 0x04 /* Write disable */
-#define OPCODE_AAI_WP 0xad /* Auto address increment word program */
-
-/* Used for Macronix flashes only. */
-#define OPCODE_EN4B 0xb7 /* Enter 4-byte mode */
-#define OPCODE_EX4B 0xe9 /* Exit 4-byte mode */
-
-/* Used for Spansion flashes only. */
-#define OPCODE_BRWR 0x17 /* Bank register write */
-
-/* Status Register bits. */
-#define SR_WIP 1 /* Write in progress */
-#define SR_WEL 2 /* Write enable latch */
-/* meaning of other SR_* bits may differ between vendors */
-#define SR_BP0 4 /* Block protect 0 */
-#define SR_BP1 8 /* Block protect 1 */
-#define SR_BP2 0x10 /* Block protect 2 */
-#define SR_SRWD 0x80 /* SR write protect */
-
-/* Define max times to check status register before we give up. */
-#define MAX_READY_WAIT 40 /* M25P16 specs 40s max chip erase */
#define MAX_CMD_SIZE 6
-#define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16)
-
-/****************************************************************************/
-
-#define SPI_NAME_SIZE 32
-
struct m25p {
struct spi_device *spi;
+ struct spi_nor spi_nor;
struct mtd_info mtd;
- u16 page_size;
- unsigned sector_size;
- u16 addr_width;
- u8 erase_opcode;
- u8 erase_opcode_4k;
- u8 *command;
+ u8 command[MAX_CMD_SIZE];
};
-static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
-{
- return container_of(mtd, struct m25p, mtd);
-}
-
-/****************************************************************************/
-
-/*
- * Internal helper functions
- */
-
-/*
- * Read the status register, returning its value in the location
- * Return the status register value.
- * Returns negative if error occurred.
- */
-static int read_sr(struct m25p *flash)
-{
- ssize_t retval;
- u8 code = OPCODE_RDSR;
- u8 val;
-
- retval = spi_write_then_read(flash->spi, &code, 1, &val, 1);
-
- if (retval < 0) {
- dev_err(&flash->spi->dev, "error %d reading SR\n",
- (int) retval);
- return retval;
- }
-
- return val;
-}
-
-/*
- * Write status register 1 byte
- * Returns negative if error occurred.
- */
-static int write_sr(struct m25p *flash, u8 val)
-{
- flash->command[0] = OPCODE_WRSR;
- flash->command[1] = val;
-
- return spi_write(flash->spi, flash->command, 2);
-}
-
-/*
- * Set write enable latch with Write Enable command.
- * Returns negative if error occurred.
- */
-static inline int write_enable(struct m25p *flash)
-{
- u8 code = OPCODE_WREN;
-
- return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
-}
-
-/*
- * Send write disble instruction to the chip.
- */
-static inline int write_disable(struct m25p *flash)
-{
- u8 code = OPCODE_WRDI;
-
- return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
-}
-
-/*
- * Enable/disable 4-byte addressing mode.
- */
-static inline int set_4byte(struct m25p *flash, u32 jedec_id, int enable)
-{
- switch (JEDEC_MFR(jedec_id)) {
- case CFI_MFR_MACRONIX:
- flash->command[0] = enable ? OPCODE_EN4B : OPCODE_EX4B;
- return spi_write(flash->spi, flash->command, 1);
- default:
- /* Spansion style */
- flash->command[0] = OPCODE_BRWR;
- flash->command[1] = enable << 7;
- return spi_write(flash->spi, flash->command, 2);
- }
-}
-
-/*
- * Service routine to read status register until ready, or timeout occurs.
- * Returns non-zero if error.
- */
-static int wait_till_ready(struct m25p *flash)
+static int m25p80_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
{
- int sr;
- uint64_t timer_start;
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
+ int ret;
- timer_start = get_time_ns();
+ ret = spi_write_then_read(spi, &code, 1, val, len);
+ if (ret < 0)
+ dev_err(&spi->dev, "error %d reading %x\n", ret, code);
- do {
- if ((sr = read_sr(flash)) < 0)
- break;
- else if (!(sr & SR_WIP))
- return 0;
-
- } while (!(is_timeout(timer_start, MAX_READY_WAIT * SECOND)));
-
- return -ETIMEDOUT;
-}
-
-/*
- * Erase the whole flash memory
- *
- * Returns 0 if successful, non-zero otherwise.
- */
-static int erase_chip(struct m25p *flash)
-{
- dev_dbg(&flash->spi->dev, "%s %lldKiB\n",
- __func__, (long long)(flash->mtd.size >> 10));
-
- /* Wait until finished previous write command. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- /* Send write enable, then erase commands. */
- write_enable(flash);
-
- /* Set up command buffer. */
- flash->command[0] = OPCODE_CHIP_ERASE;
-
- spi_write(flash->spi, flash->command, 1);
-
- return 0;
+ return ret;
}
-static void m25p_addr2cmd(struct m25p *flash, unsigned int addr, u8 *cmd)
+static void m25p_addr2cmd(struct spi_nor *nor, unsigned int addr, u8 *cmd)
{
/* opcode is in cmd[0] */
- cmd[1] = addr >> (flash->addr_width * 8 - 8);
- cmd[2] = addr >> (flash->addr_width * 8 - 16);
- cmd[3] = addr >> (flash->addr_width * 8 - 24);
- cmd[4] = addr >> (flash->addr_width * 8 - 32);
+ cmd[1] = addr >> (nor->addr_width * 8 - 8);
+ cmd[2] = addr >> (nor->addr_width * 8 - 16);
+ cmd[3] = addr >> (nor->addr_width * 8 - 24);
+ cmd[4] = addr >> (nor->addr_width * 8 - 32);
}
-static int m25p_cmdsz(struct m25p *flash)
+static int m25p_cmdsz(struct spi_nor *nor)
{
- return 1 + flash->addr_width;
-}
-
-/*
- * Erase one sector of flash memory at offset ``offset'' which is any
- * address within the sector which should be erased.
- *
- * Returns 0 if successful, non-zero otherwise.
- */
-static int erase_sector(struct m25p *flash, u32 offset, u32 command)
-{
- dev_dbg(&flash->spi->dev, "%s %dKiB at 0x%08x\n",
- __func__, flash->mtd.erasesize / 1024, offset);
-
- /* Wait until finished previous write command. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- /* Send write enable, then erase commands. */
- write_enable(flash);
-
- /* Set up command buffer. */
- flash->command[0] = command;
- m25p_addr2cmd(flash, offset, flash->command);
-
- spi_write(flash->spi, flash->command, m25p_cmdsz(flash));
-
- return 0;
+ return 1 + nor->addr_width;
}
-/****************************************************************************/
-
-/*
- * MTD implementation
- */
-
-/*
- * Erase an address range on the flash chip. The address range may extend
- * one or more erase sectors. Return an error is there is a problem erasing.
- */
-static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr)
+static int m25p80_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len,
+ int wr_en)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- u32 addr;
- uint32_t rem;
- uint64_t len;
-
- dev_dbg(&flash->spi->dev, "%s at 0x%llx, len %lld\n",
- __func__, (long long)instr->addr,
- (long long)instr->len);
-
- div_u64_rem(instr->len, mtd->erasesize, &rem);
- if (rem)
- return -EINVAL;
-
- addr = instr->addr;
- len = instr->len;
-
- /* whole-chip erase? */
- if (len == flash->mtd.size) {
- if (erase_chip(flash)) {
- instr->state = MTD_ERASE_FAILED;
- return -EIO;
- }
- return 0;
- }
-
- if (flash->erase_opcode_4k) {
- while (len && (addr & (flash->sector_size - 1))) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode_4k))
- return -EIO;
- addr += mtd->erasesize;
- len -= mtd->erasesize;
- }
-
- while (len >= flash->sector_size) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode))
- return -EIO;
- addr += flash->sector_size;
- len -= flash->sector_size;
- }
-
- while (len) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode_4k))
- return -EIO;
- addr += mtd->erasesize;
- len -= mtd->erasesize;
- }
- } else {
- while (len) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode))
- return -EIO;
-
- if (len <= mtd->erasesize)
- break;
- addr += mtd->erasesize;
- len -= mtd->erasesize;
- }
- }
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
+ flash->command[0] = opcode;
+ if (buf)
+ memcpy(&flash->command[1], buf, len);
- instr->state = MTD_ERASE_DONE;
- mtd_erase_callback(instr);
-
- return 0;
+ return spi_write(spi, flash->command, len + 1);
}
-/*
- * Read an address range from the flash chip. The address range
- * may be any size provided it is within the physical boundaries.
- */
-static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf)
+static void m25p80_write(struct spi_nor *nor, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- struct spi_transfer t[2];
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
+ struct spi_transfer t[2] = {};
struct spi_message m;
- int fast_read = 0;
-
- if (flash->spi->max_speed_hz >= 25000000)
- fast_read = 1;
+ int cmd_sz = m25p_cmdsz(nor);
spi_message_init(&m);
- memset(t, 0, (sizeof t));
- /* NOTE:
- * OPCODE_FAST_READ (if available) is faster.
- * Should add 1 byte DUMMY_BYTE.
- */
+ if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
+ cmd_sz = 1;
+
+ flash->command[0] = nor->program_opcode;
+ m25p_addr2cmd(nor, to, flash->command);
+
t[0].tx_buf = flash->command;
- t[0].len = m25p_cmdsz(flash) + fast_read;
+ t[0].len = cmd_sz;
spi_message_add_tail(&t[0], &m);
- t[1].rx_buf = buf;
+ t[1].tx_buf = buf;
t[1].len = len;
spi_message_add_tail(&t[1], &m);
- /* Wait till previous write/erase is done. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- /* FIXME switch to OPCODE_FAST_READ. It's required for higher
- * clocks; and at this writing, every chip this driver handles
- * supports that opcode.
- */
+ spi_sync(spi, &m);
- /* Set up the write data buffer. */
- flash->command[0] = fast_read ? OPCODE_FAST_READ : OPCODE_NORM_READ;
- m25p_addr2cmd(flash, from, flash->command);
-
- spi_sync(flash->spi, &m);
-
- *retlen = m.actual_length - m25p_cmdsz(flash) - fast_read;
-
- return 0;
+ *retlen += m.actual_length - cmd_sz;
}
/*
- * Write an address range to the flash chip. Data must be written in
- * FLASH_PAGESIZE chunks. The address range may be any size provided
- * it is within the physical boundaries.
+ * Read an address range from the nor chip. The address range
+ * may be any size provided it is within the physical boundaries.
*/
-static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
+static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- u32 page_offset, page_size;
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
struct spi_transfer t[2];
struct spi_message m;
+ unsigned int dummy = nor->read_dummy;
- dev_dbg(&flash->spi->dev, "m25p80_write %ld bytes at 0x%08llx\n",
- (unsigned long)len, to);
+ /* convert the dummy cycles to the number of bytes */
+ dummy /= 8;
spi_message_init(&m);
memset(t, 0, (sizeof t));
+ flash->command[0] = nor->read_opcode;
+ m25p_addr2cmd(nor, from, flash->command);
+
t[0].tx_buf = flash->command;
- t[0].len = m25p_cmdsz(flash);
+ t[0].len = m25p_cmdsz(nor) + dummy;
spi_message_add_tail(&t[0], &m);
- t[1].tx_buf = buf;
+ t[1].rx_buf = buf;
+ t[1].len = len;
spi_message_add_tail(&t[1], &m);
- /* Wait until finished previous write command. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- write_enable(flash);
-
- /* Set up the opcode in the write buffer. */
- flash->command[0] = OPCODE_PP;
- m25p_addr2cmd(flash, to, flash->command);
-
- page_offset = to & (flash->page_size - 1);
-
- /* do all the bytes fit onto one page? */
- if (page_offset + len <= flash->page_size) {
- t[1].len = len;
-
- spi_sync(flash->spi, &m);
-
- *retlen = m.actual_length - m25p_cmdsz(flash);
- } else {
- u32 i;
-
- /* the size of data remaining on the first page */
- page_size = flash->page_size - page_offset;
-
- t[1].len = page_size;
- spi_sync(flash->spi, &m);
-
- *retlen = m.actual_length - m25p_cmdsz(flash);
-
- /* write everything in flash->page_size chunks */
- for (i = page_size; i < len; i += page_size) {
- page_size = len - i;
- if (page_size > flash->page_size)
- page_size = flash->page_size;
-
- /* write the next page to flash */
- m25p_addr2cmd(flash, to + i, flash->command);
-
- t[1].tx_buf = buf + i;
- t[1].len = page_size;
-
- wait_till_ready(flash);
-
- write_enable(flash);
-
- spi_sync(flash->spi, &m);
-
- *retlen += m.actual_length - m25p_cmdsz(flash);
- }
- }
+ spi_sync(spi, &m);
+ *retlen = m.actual_length - m25p_cmdsz(nor) - dummy;
return 0;
}
-static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
+static int m25p80_erase(struct spi_nor *nor, loff_t offset)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- struct spi_transfer t[2];
- struct spi_message m;
- size_t actual;
- int cmd_sz, ret;
+ struct m25p *flash = nor->priv;
- dev_dbg(&flash->spi->dev, "%s to 0x%08x, len %zd\n",
- __func__, (u32)to, len);
+ dev_dbg(nor->dev, "%dKiB at 0x%08x\n",
+ flash->mtd.erasesize / 1024, (u32)offset);
- spi_message_init(&m);
- memset(t, 0, (sizeof t));
+ /* Set up command buffer. */
+ flash->command[0] = nor->erase_opcode;
+ m25p_addr2cmd(nor, offset, flash->command);
- t[0].tx_buf = flash->command;
- t[0].len = m25p_cmdsz(flash);
- spi_message_add_tail(&t[0], &m);
+ spi_write(flash->spi, flash->command, m25p_cmdsz(nor));
- t[1].tx_buf = buf;
- spi_message_add_tail(&t[1], &m);
-
- /* Wait until finished previous write command. */
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
-
- write_enable(flash);
-
- actual = to % 2;
- /* Start write from odd address. */
- if (actual) {
- flash->command[0] = OPCODE_BP;
- m25p_addr2cmd(flash, to, flash->command);
-
- /* write one byte. */
- t[1].len = 1;
- spi_sync(flash->spi, &m);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
- *retlen += m.actual_length - m25p_cmdsz(flash);
- }
- to += actual;
-
- flash->command[0] = OPCODE_AAI_WP;
- m25p_addr2cmd(flash, to, flash->command);
-
- /* Write out most of the data here. */
- cmd_sz = m25p_cmdsz(flash);
- for (; actual < len - 1; actual += 2) {
- t[0].len = cmd_sz;
- /* write two bytes. */
- t[1].len = 2;
- t[1].tx_buf = buf + actual;
-
- spi_sync(flash->spi, &m);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
- *retlen += m.actual_length - cmd_sz;
- cmd_sz = 1;
- to += 2;
- }
- write_disable(flash);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
-
- /* Write out trailing byte if it exists. */
- if (actual != len) {
- write_enable(flash);
- flash->command[0] = OPCODE_BP;
- m25p_addr2cmd(flash, to, flash->command);
- t[0].len = m25p_cmdsz(flash);
- t[1].len = 1;
- t[1].tx_buf = buf + actual;
-
- spi_sync(flash->spi, &m);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
- *retlen += m.actual_length - m25p_cmdsz(flash);
- write_disable(flash);
- }
-
-time_out:
- return ret;
+ return 0;
}
-/****************************************************************************/
-
/*
- * SPI device driver setup and teardown
- */
-
-struct flash_info {
- /* JEDEC id zero means "no ID" (most older chips); otherwise it has
- * a high byte of zero plus three data bytes: the manufacturer id,
- * then a two byte device id.
- */
- u32 jedec_id;
- u16 ext_id;
-
- /* The size listed here is what works with OPCODE_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
- unsigned sector_size;
- u16 n_sectors;
-
- u16 page_size;
- u16 addr_width;
-
- u16 flags;
-#define SECT_4K 0x01 /* OPCODE_BE_4K works uniformly */
-#define M25P_NO_ERASE 0x02 /* No erase command needed */
-};
-
-#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- ((unsigned long)&(struct flash_info) { \
- .jedec_id = (_jedec_id), \
- .ext_id = (_ext_id), \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags), \
- })
-
-#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width) \
- ((unsigned long)&(struct flash_info) { \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = (_page_size), \
- .addr_width = (_addr_width), \
- .flags = M25P_NO_ERASE, \
- })
-
-/* NOTE: double check command sets and memory organization when you add
- * more flash chips. This current list focusses on newer chips, which
- * have been converging on command sets which including JEDEC ID.
+ * Do NOT add to this array without reading the following:
+ *
+ * Historically, many flash devices are bound to this driver by their name. But
+ * since most of these flash are compatible to some extent, and their
+ * differences can often be differentiated by the JEDEC read-ID command, we
+ * encourage new users to add support to the spi-nor library, and simply bind
+ * against a generic string here (e.g., "nor-jedec").
+ *
+ * Many flash names are kept here in this list (as well as in spi-nor.c) to
+ * keep them available as module aliases for existing platforms.
*/
static const struct platform_device_id m25p_ids[] = {
- /* Atmel -- some are (confusingly) marketed as "DataFlash" */
- { "at25fs010", INFO(0x1f6601, 0, 32 * 1024, 4, SECT_4K) },
- { "at25fs040", INFO(0x1f6604, 0, 64 * 1024, 8, SECT_4K) },
-
- { "at25df041a", INFO(0x1f4401, 0, 64 * 1024, 8, SECT_4K) },
- { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
- { "at25df641", INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) },
-
- { "at26f004", INFO(0x1f0400, 0, 64 * 1024, 8, SECT_4K) },
- { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
- { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) },
- { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
-
- { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
-
- /* EON -- en25xxx */
- { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) },
- { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) },
- { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
- { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) },
- { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
-
- /* Everspin */
- { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2) },
-
- /* Intel/Numonyx -- xxxs33b */
- { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) },
- { "320s33b", INFO(0x898912, 0, 64 * 1024, 64, 0) },
- { "640s33b", INFO(0x898913, 0, 64 * 1024, 128, 0) },
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
-
- /* Macronix */
- { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
- { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
- { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
- { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
- { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) },
- { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) },
- { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
- { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
- { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
- { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
-
- /* Micron */
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
- { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) },
- { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
- { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) },
-
- /* Spansion -- single (large) sector size only, at least
- * for the chips listed here (without boot sectors).
- */
- { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, 0) },
- { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 0) },
- { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) },
- { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, 0) },
- { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, 0) },
- { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) },
- { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
- { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
- { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 0) },
- { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 0) },
- { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
- { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
- { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
- { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
- { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
- { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, SECT_4K) },
- { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
-
- /* SST -- large erase sizes are "overlays", "sectors" are 4K */
- { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K) },
- { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K) },
- { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K) },
- { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K) },
- { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K) },
- { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K) },
- { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K) },
- { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K) },
-
- /* ST Microelectronics -- newer production may have feature updates */
- { "m25p05", INFO(0x202010, 0, 32 * 1024, 2, 0) },
- { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
- { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
- { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
- { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
- { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
- { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
- { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
- { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
- { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) },
-
- { "m25p05-nonjedec", INFO(0, 0, 32 * 1024, 2, 0) },
- { "m25p10-nonjedec", INFO(0, 0, 32 * 1024, 4, 0) },
- { "m25p20-nonjedec", INFO(0, 0, 64 * 1024, 4, 0) },
- { "m25p40-nonjedec", INFO(0, 0, 64 * 1024, 8, 0) },
- { "m25p80-nonjedec", INFO(0, 0, 64 * 1024, 16, 0) },
- { "m25p16-nonjedec", INFO(0, 0, 64 * 1024, 32, 0) },
- { "m25p32-nonjedec", INFO(0, 0, 64 * 1024, 64, 0) },
- { "m25p64-nonjedec", INFO(0, 0, 64 * 1024, 128, 0) },
- { "m25p128-nonjedec", INFO(0, 0, 256 * 1024, 64, 0) },
-
- { "m45pe10", INFO(0x204011, 0, 64 * 1024, 2, 0) },
- { "m45pe80", INFO(0x204014, 0, 64 * 1024, 16, 0) },
- { "m45pe16", INFO(0x204015, 0, 64 * 1024, 32, 0) },
-
- { "m25pe20", INFO(0x208012, 0, 64 * 1024, 4, 0) },
- { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) },
- { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
-
- { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) },
- { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) },
- { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) },
- { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
-
- /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
- { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
- { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
- { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
- { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
- { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
- { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
-
- /* Catalyst / On Semiconductor -- non-JEDEC */
- { "cat25c11", CAT25_INFO( 16, 8, 16, 1) },
- { "cat25c03", CAT25_INFO( 32, 8, 16, 2) },
- { "cat25c09", CAT25_INFO( 128, 8, 32, 2) },
- { "cat25c17", CAT25_INFO( 256, 8, 32, 2) },
- { "cat25128", CAT25_INFO(2048, 8, 64, 2) },
+ {"at25fs010"}, {"at25fs040"}, {"at25df041a"}, {"at25df321a"},
+ {"at25df641"}, {"at26f004"}, {"at26df081a"}, {"at26df161a"},
+ {"at26df321"}, {"at45db081d"},
+ {"en25f32"}, {"en25p32"}, {"en25q32b"}, {"en25p64"},
+ {"en25q64"}, {"en25qh128"}, {"en25qh256"},
+ {"f25l32pa"},
+ {"mr25h256"}, {"mr25h10"},
+ {"gd25q32"}, {"gd25q64"},
+ {"160s33b"}, {"320s33b"}, {"640s33b"},
+ {"mx25l2005a"}, {"mx25l4005a"}, {"mx25l8005"}, {"mx25l1606e"},
+ {"mx25l3205d"}, {"mx25l3255e"}, {"mx25l6405d"}, {"mx25l12805d"},
+ {"mx25l12855e"},{"mx25l25635e"},{"mx25l25655e"},{"mx66l51235l"},
+ {"mx66l1g55g"},
+ {"n25q064"}, {"n25q128a11"}, {"n25q128a13"}, {"n25q256a"},
+ {"n25q512a"}, {"n25q512ax3"}, {"n25q00"},
+ {"pm25lv512"}, {"pm25lv010"}, {"pm25lq032"},
+ {"s25sl032p"}, {"s25sl064p"}, {"s25fl256s0"}, {"s25fl256s1"},
+ {"s25fl512s"}, {"s70fl01gs"}, {"s25sl12800"}, {"s25sl12801"},
+ {"s25fl129p0"}, {"s25fl129p1"}, {"s25sl004a"}, {"s25sl008a"},
+ {"s25sl016a"}, {"s25sl032a"}, {"s25sl064a"}, {"s25fl008k"},
+ {"s25fl016k"}, {"s25fl064k"}, {"s25fl132k"},
+ {"sst25vf040b"},{"sst25vf080b"},{"sst25vf016b"},{"sst25vf032b"},
+ {"sst25vf064c"},{"sst25wf512"}, {"sst25wf010"}, {"sst25wf020"},
+ {"sst25wf040"},
+ {"m25p05"}, {"m25p10"}, {"m25p20"}, {"m25p40"},
+ {"m25p80"}, {"m25p16"}, {"m25p32"}, {"m25p64"},
+ {"m25p128"}, {"n25q032"},
+ {"m25p05-nonjedec"}, {"m25p10-nonjedec"}, {"m25p20-nonjedec"},
+ {"m25p40-nonjedec"}, {"m25p80-nonjedec"}, {"m25p16-nonjedec"},
+ {"m25p32-nonjedec"}, {"m25p64-nonjedec"}, {"m25p128-nonjedec"},
+ {"m45pe10"}, {"m45pe80"}, {"m45pe16"},
+ {"m25pe20"}, {"m25pe80"}, {"m25pe16"},
+ {"m25px16"}, {"m25px32"}, {"m25px32-s0"}, {"m25px32-s1"},
+ {"m25px64"}, {"m25px80"},
+ {"w25x10"}, {"w25x20"}, {"w25x40"}, {"w25x80"},
+ {"w25x16"}, {"w25x32"}, {"w25q32"}, {"w25q32dw"},
+ {"w25x64"}, {"w25q64"}, {"w25q80"}, {"w25q80bl"},
+ {"w25q128"}, {"w25q256"}, {"cat25c11"},
+ {"cat25c03"}, {"cat25c09"}, {"cat25c17"}, {"cat25128"},
+
+ /*
+ * Generic support for SPI NOR that can be identified by the JEDEC READ
+ * ID opcode (0x9F). Use this, if possible.
+ */
+ {"nor-jedec"},
{ },
};
-static const struct platform_device_id *jedec_probe(struct spi_device *spi)
-{
- int tmp;
- u8 code = OPCODE_RDID;
- u8 id[5];
- u32 jedec;
- u16 ext_jedec;
- struct flash_info *info;
-
- /* JEDEC also defines an optional "extended device information"
- * string for after vendor-specific data, after the three bytes
- * we use here. Supporting some chips might require using it.
- */
- tmp = spi_write_then_read(spi, &code, 1, id, 5);
- if (tmp < 0) {
- dev_dbg(&spi->dev, "%s: error %d reading JEDEC ID\n",
- dev_name(&spi->dev), tmp);
- return ERR_PTR(tmp);
- }
- jedec = id[0];
- jedec = jedec << 8;
- jedec |= id[1];
- jedec = jedec << 8;
- jedec |= id[2];
-
- ext_jedec = id[3] << 8 | id[4];
-
- for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) {
- info = (void *)m25p_ids[tmp].driver_data;
- if (info->jedec_id == jedec) {
- if (info->ext_id != 0 && info->ext_id != ext_jedec)
- continue;
- return &m25p_ids[tmp];
- }
- }
- dev_err(&spi->dev, "unrecognized JEDEC id %06x\n", jedec);
- return ERR_PTR(-ENODEV);
-}
-
-
/*
* board specific setup should have ensured the SPI clock used here
* matches what the READ command supports, at least until this driver
@@ -801,164 +229,68 @@ static const struct platform_device_id *jedec_probe(struct spi_device *spi)
static int m25p_probe(struct device_d *dev)
{
struct spi_device *spi = (struct spi_device *)dev->type_data;
- const struct platform_device_id *id = NULL;
struct flash_platform_data *data;
struct m25p *flash;
- struct flash_info *info = NULL;
- unsigned i;
- unsigned do_jdec_probe = 1;
- char *flashname = NULL;
- const char *typename = NULL;
+ struct spi_nor *nor;
+ enum read_mode mode = SPI_NOR_NORMAL;
+ char *flash_name = NULL;
int device_id;
+ int ret;
- /* Platform data helps sort out which chip type we have, as
- * well as how this board partitions it. If we don't have
- * a chip ID, try the JEDEC id commands; they'll work for most
- * newer chips, even if we don't recognize the particular chip.
- */
data = dev->platform_data;
- if (data && data->type)
- typename = data->type;
- else if (dev->id_entry)
- typename = dev->id_entry->name;
-
- if (typename) {
- const struct platform_device_id *plat_id;
-
- for (i = 0; i < ARRAY_SIZE(m25p_ids) - 1; i++) {
- plat_id = &m25p_ids[i];
- if (strcmp(typename, plat_id->name))
- continue;
- break;
- }
-
- if (i < ARRAY_SIZE(m25p_ids) - 1) {
- id = plat_id;
- info = (void *)id->driver_data;
- /* If flash type is provided but the memory is not
- * JEDEC compliant, don't try to probe the JEDEC id */
- if (!info->jedec_id)
- do_jdec_probe = 0;
- } else
- dev_warn(&spi->dev, "unrecognized id %s\n", typename);
- }
-
- if (do_jdec_probe) {
- const struct platform_device_id *jid;
-
- jid = jedec_probe(spi);
- if (IS_ERR(jid)) {
- return PTR_ERR(jid);
- } else if (jid != id) {
- /*
- * JEDEC knows better, so overwrite platform ID. We
- * can't trust partitions any longer, but we'll let
- * mtd apply them anyway, since some partitions may be
- * marked read-only, and we don't want to lose that
- * information, even if it's not 100% accurate.
- */
- if (id)
- dev_warn(dev, "found %s, expected %s\n",
- jid->name, id->name);
-
- id = jid;
- info = (void *)jid->driver_data;
- }
- }
flash = xzalloc(sizeof *flash);
- flash->command = xmalloc(MAX_CMD_SIZE);
+ nor = &flash->spi_nor;
+
+ /* install the hooks */
+ nor->read = m25p80_read;
+ nor->write = m25p80_write;
+ nor->erase = m25p80_erase;
+ nor->write_reg = m25p80_write_reg;
+ nor->read_reg = m25p80_read_reg;
+
+ nor->dev = dev;
+ nor->mtd = &flash->mtd;
+ nor->priv = flash;
+
+ flash->mtd.priv = nor;
+ flash->mtd.parent = &spi->dev;
flash->spi = spi;
+
dev->priv = (void *)flash;
- /*
- * Atmel, SST and Intel/Numonyx serial flash tend to power
- * up with the software protection bits set
- */
-
- if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL ||
- JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL ||
- JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) {
- write_enable(flash);
- write_sr(flash, 0);
- }
+
+ if (data && data->name)
+ flash->mtd.name = data->name;
+
+ if (data && data->type)
+ flash_name = data->type;
+ else if (data && data->name)
+ flash_name = data->name;
+ else if (dev->id_entry)
+ flash_name = dev->id_entry->name;
+ else
+ flash_name = NULL; /* auto-detect */
+
+ ret = spi_nor_scan(nor, flash_name, mode);
+ if (ret)
+ return ret;
device_id = DEVICE_ID_SINGLE;
if (dev->device_node) {
const char *alias = of_alias_get(dev->device_node);
if (alias)
- flashname = xstrdup(alias);
+ flash_name = xstrdup(alias);
} else if (data && data->name) {
- flashname = data->name;
+ flash_name = data->name;
}
- if (!flashname) {
+ if (!flash_name) {
device_id = DEVICE_ID_DYNAMIC;
- flashname = "m25p";
- }
-
- flash->mtd.type = MTD_NORFLASH;
- flash->mtd.writesize = 1;
- flash->mtd.flags = MTD_CAP_NORFLASH;
- flash->mtd.size = (uint64_t)info->sector_size * info->n_sectors;
- flash->mtd.erase = m25p80_erase;
- flash->mtd.read = m25p80_read;
-
- /* sst flash chips use AAI word program */
- if (IS_ENABLED(CONFIG_MTD_SST25L) && JEDEC_MFR(info->jedec_id) == CFI_MFR_SST)
- flash->mtd.write = sst_write;
- else
- flash->mtd.write = m25p80_write;
-
- /* prefer "small sector" erase if possible */
- if (info->flags & SECT_4K) {
- flash->erase_opcode_4k = OPCODE_BE_4K;
- flash->erase_opcode = OPCODE_SE;
- flash->mtd.erasesize = 4096;
- } else {
- flash->erase_opcode = OPCODE_SE;
- flash->mtd.erasesize = info->sector_size;
- }
-
- if (info->flags & M25P_NO_ERASE)
- flash->mtd.flags |= MTD_NO_ERASE;
-
- flash->mtd.parent = &spi->dev;
- flash->page_size = info->page_size;
- flash->sector_size = info->sector_size;
-
- if (info->addr_width)
- flash->addr_width = info->addr_width;
- else {
- /* enable 4-byte addressing if the device exceeds 16MiB */
- if (flash->mtd.size > 0x1000000) {
- flash->addr_width = 4;
- set_4byte(flash, info->jedec_id, 1);
- } else
- flash->addr_width = 3;
+ flash_name = "m25p";
}
- dev_info(dev, "%s (%lld Kbytes)\n", id->name,
- (long long)flash->mtd.size >> 10);
-
- dev_dbg(dev, "mtd .name = %s, .size = 0x%llx (%lldMiB) "
- ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n",
- flash->mtd.name,
- (long long)flash->mtd.size, (long long)(flash->mtd.size >> 20),
- flash->mtd.erasesize, flash->mtd.erasesize / 1024,
- flash->mtd.numeraseregions);
-
- if (flash->mtd.numeraseregions)
- for (i = 0; i < flash->mtd.numeraseregions; i++)
- dev_dbg(dev, "mtd.eraseregions[%d] = { .offset = 0x%llx, "
- ".erasesize = 0x%.8x (%uKiB), "
- ".numblocks = %d }\n",
- i, (long long)flash->mtd.eraseregions[i].offset,
- flash->mtd.eraseregions[i].erasesize,
- flash->mtd.eraseregions[i].erasesize / 1024,
- flash->mtd.eraseregions[i].numblocks);
-
- return add_mtd_device(&flash->mtd, flashname, device_id);
+ return add_mtd_device(&flash->mtd, flash_name, device_id);
}
static __maybe_unused struct of_device_id m25p80_dt_ids[] = {
--
2.1.4
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
