Am 15.10.2012 23:42, schrieb Vicente Bergas:
diff --git a/arch/arm/mach-omap/include/mach/omap4-silicon.h b/arch/arm/mach-omap/include/mach/omap4-silicon.h
index 71ffe39..137cc88 100644
--- a/arch/arm/mach-omap/include/mach/omap4-silicon.h
+++ b/arch/arm/mach-omap/include/mach/omap4-silicon.h
@@ -196,6 +196,6 @@ struct dpll_param;
void omap4_ddr_init(const struct ddr_regs *, const struct dpll_param *);
void omap4_power_i2c_send(u32);
unsigned int omap4_revision(void);
-noinline int omap4_scale_vcores(unsigned vsel0_pin);
+noinline int omap4_scale_vcores(int vsel0_pin);
#endif
diff --git a/arch/arm/mach-omap/omap4_clock.c b/arch/arm/mach-omap/omap4_clock.c
index 1481f16..f7927d2 100644
--- a/arch/arm/mach-omap/omap4_clock.c
+++ b/arch/arm/mach-omap/omap4_clock.c
@@ -394,9 +394,38 @@ void omap4_enable_all_clocks(void)
sr32(CM_L3INIT_USBPHY_CLKCTRL, 0, 32, 0x301);
}
-void omap4_do_scale_tps62361(u32 reg, u32 volt_mv)
+#define GPIO_MASK 0x1f
+#define GPIO_OE 0x34
+#define GPIO_CLEARDATAOUT 0x90
+#define GPIO_SETDATAOUT 0x94
+
+static void __iomem *omap4_get_gpio_base(unsigned gpio)
+{
+ void __iomem *base;
+
+ if (gpio < 32)
+ base = (void *)0x4a310100;
+ else
+ base = (void *)(0x48053100 + ((gpio & ~GPIO_MASK) << 8));
+
+ return base;
+}
+
+void omap4_do_scale_tps62361(int vsel0_pin, u32 reg, u32 volt_mv)
{
u32 temp, step;
+ void __iomem *base;
+ u32 val;
+
+ /* Pull the GPIO low to select SET0 register, while we program SET1 */
+ if (vsel0_pin >= 0) {
+ base = omap4_get_gpio_base(vsel0_pin);
+ val = 1 << (vsel0_pin & GPIO_MASK);
+ writel(val, base + GPIO_CLEARDATAOUT);
+ val = readl(base + GPIO_OE);
+ val &= (1 << (vsel0_pin & GPIO_MASK));
Please note that the bit needs to be set to zero here to
set it to output. So it was wrong in my patch.
I have fixed it now. Please take a look in the
ARM OMAP: Enable gpio output patch.
Teresa
+ writel(val, base + GPIO_OE);
+ }
step = volt_mv - TPS62361_BASE_VOLT_MV;
step /= 10;
@@ -411,4 +440,10 @@ void omap4_do_scale_tps62361(u32 reg, u32 volt_mv)
if (!wait_on_value(OMAP44XX_PRM_VC_VAL_BYPASS_VALID_BIT, 0,
OMAP44XX_PRM_VC_VAL_BYPASS, LDELAY))
puts("Scaling voltage failed for vdd_mpu from TPS\n");
+
+ /* Pull the GPIO high to select SET1 register */
+ if (vsel0_pin >= 0) {
+ val = 1 << (vsel0_pin & GPIO_MASK);
+ writel(val, base + GPIO_SETDATAOUT);
+ }
}
diff --git a/arch/arm/mach-omap/omap4_generic.c b/arch/arm/mach-omap/omap4_generic.c
index 765fcb5..8e692ba 100644
--- a/arch/arm/mach-omap/omap4_generic.c
+++ b/arch/arm/mach-omap/omap4_generic.c
@@ -495,27 +495,11 @@ enum omap_boot_src omap4_bootsrc(void)
return OMAP_BOOTSRC_UNKNOWN;
}
-#define GPIO_MASK 0x1f
-
-static void __iomem *omap4_get_gpio_base(unsigned gpio)
-{
- void __iomem *base;
-
- if (gpio < 32)
- base = (void *)0x4a310000;
- else
- base = (void *)(0x48053000 + ((gpio & ~GPIO_MASK) << 8));
-
- return base;
-}
-
#define I2C_SLAVE 0x12
-noinline int omap4_scale_vcores(unsigned vsel0_pin)
+noinline int omap4_scale_vcores(int vsel0_pin)
{
- void __iomem *base;
unsigned int rev = omap4_revision();
- u32 val = 0;
/* For VC bypass only VCOREx_CGF_FORCE is necessary and
* VCOREx_CFG_VOLTAGE changes can be discarded
@@ -523,33 +507,6 @@ noinline int omap4_scale_vcores(unsigned vsel0_pin)
writel(0, OMAP44XX_PRM_VC_CFG_I2C_MODE);
writel(0x6026, OMAP44XX_PRM_VC_CFG_I2C_CLK);
- /* TPS - supplies vdd_mpu on 4460 */
- if (rev >= OMAP4460_ES1_0) {
- /*
- * Setup SET1 and SET0 with right values so that kernel
- * can use either of them based on its needs.
- */
- omap4_do_scale_tps62361(TPS62361_REG_ADDR_SET0, 1430);
- omap4_do_scale_tps62361(TPS62361_REG_ADDR_SET1, 1430);
-
- /*
- * Select SET1 in TPS62361:
- * VSEL1 is grounded on board. So the following selects
- * VSEL1 = 0 and VSEL0 = 1
- */
- base = omap4_get_gpio_base(vsel0_pin);
-
- val = 1 << (vsel0_pin & GPIO_MASK);
- writel(val, base + 0x190);
-
- val = readl(base + 0x134);
- val &= (1 << (vsel0_pin & GPIO_MASK));
- writel(val, base + 0x134);
-
- val = 1 << (vsel0_pin & GPIO_MASK);
- writel(val, base + 0x194);
- }
-
/* set VCORE1 force VSEL */
/*
* 4430 : supplies vdd_mpu
@@ -568,8 +525,13 @@ noinline int omap4_scale_vcores(unsigned vsel0_pin)
/* 0x55: i2c addr, 28: ~ 1200 mvolts*/
omap4_power_i2c_send((0x2855 << 8) | I2C_SLAVE);
+ /* TPS - supplies vdd_mpu on 4460 */
+ if (rev >= OMAP4460_ES1_0)
+ omap4_do_scale_tps62361(vsel0_pin,
+ TPS62361_REG_ADDR_SET1, 1203);
+
/* FIXME: set VCORE2 force VSEL, Check the reset value */
- omap4_power_i2c_send((0x295B << 8) | I2C_SLAVE);
+ omap4_power_i2c_send((0x285B << 8) | I2C_SLAVE);
/* set VCORE3 force VSEL */
switch (rev) {
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
