Hi Juergen,
On Mon, Oct 11, 2010 at 2:48 PM, Juergen Beisert <jbe@xxxxxxxxxxxxxx> wrote:
> Sascha Hauer wrote:
>> With SD cards older than 2.0 the sd_send_if_cond() fails. Do
>> not assume it's an MMC card in this case. Instead, assume
>> it's a MMC card if sd_send_op_cond() fails.
>>
>> Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
>> ---
>> Âdrivers/mci/mci-core.c | Â 24 +++++++-----------------
>> Â1 files changed, 7 insertions(+), 17 deletions(-)
>>
>> diff --git a/drivers/mci/mci-core.c b/drivers/mci/mci-core.c
>> index a6c81b8..57b82bf 100644
>> --- a/drivers/mci/mci-core.c
>> +++ b/drivers/mci/mci-core.c
>> @@ -1148,26 +1148,16 @@ static int mci_card_probe(struct device_d *mci_dev)
>>
>> Â Â Â /* Check if this card can handle the "SD Card Physical Layer
>> Specification 2.0" */ rc = sd_send_if_cond(mci_dev);
>> - Â Â if (rc) {
>> + Â Â rc = sd_send_op_cond(mci_dev);
>> + Â Â if (rc && rc == -ETIMEDOUT) {
>> Â Â Â Â Â Â Â /* If the command timed out, we check for an MMC card */
>> - Â Â Â Â Â Â if (rc == -ETIMEDOUT) {
>> - Â Â Â Â Â Â Â Â Â Â pr_debug("Card seems to be a MultiMediaCard\n");
>> - Â Â Â Â Â Â Â Â Â Â rc = mmc_send_op_cond(mci_dev);
>> - Â Â Â Â Â Â Â Â Â Â if (rc) {
>> - Â Â Â Â Â Â Â Â Â Â Â Â Â Â pr_err("MultiMediaCard voltage select failed with %d\n", rc);
>> - Â Â Â Â Â Â Â Â Â Â Â Â Â Â goto on_error;
>> - Â Â Â Â Â Â Â Â Â Â }
>> - Â Â Â Â Â Â } else
>> - Â Â Â Â Â Â Â Â Â Â goto on_error;
>> - Â Â } else {
>> - Â Â Â Â Â Â /* Its a 2.xx card. Setup operation conditions */
>> - Â Â Â Â Â Â rc = sd_send_op_cond(mci_dev);
>> - Â Â Â Â Â Â if (rc) {
>> - Â Â Â Â Â Â Â Â Â Â pr_debug("Cannot setup SD card's operation condition\n");
>> - Â Â Â Â Â Â Â Â Â Â goto on_error;
>> - Â Â Â Â Â Â }
>> + Â Â Â Â Â Â pr_debug("Card seems to be a MultiMediaCard\n");
>> + Â Â Â Â Â Â rc = mmc_send_op_cond(mci_dev);
>> Â Â Â }
>>
>> + Â Â if (rc)
>> + Â Â Â Â Â Â goto on_error;
>> +
>> Â Â Â rc = mci_startup(mci_dev);
>> Â Â Â if (rc) {
>> Â Â Â Â Â Â Â printf("Card's startup fails with %d\n", rc);
>
> Tested-by: Juergen Beisert <jbe@xxxxxxxxxxxxxx>
>
> @Marek: You need this patch to make your SD card work on the mini2440.
After applying a patch it 's better but it hangs:
IO settings: bus width=1, frequency=0 Hz
IO settings: bus width=1, frequency=200098 Hz
Command with response
Command with response
Command with response
Command with response
Put the Card in Identify Mode
Command with response
Command with long response
Card's identification data is: 1B534D53-44202020-10C811B9-74008197
Get/Set relative address
Command with response
Get card's specific data
Command with response
Command with long response
Card's specific data is: 002F0032-5F5983CA-6DB7FF9F-96400063
Transfer speed: 25000000
Max. block length are: Write=512, Read=512 Bytes
Capacity: 970 MiB
Read block length: 512, Write block length: 512
Select the card, and put it into Transfer Mode
Command with response
Changing transfer frequency
Command with response
Trying to read the SCR (try 1 of 3)
Command with response
Command with response
Command with response
IO settings: bus width=1, frequency=50625000 Hz
Command with response
Card is up and running now, registering as a disk
mci_sd_read called: Read 1 block(s), starting at 0 to 31BBFBB9
Command with response
Than it hangs maybe in while(1) in s3c_send_command?
>
> jbe
>
> --
> Pengutronix e.K.               Â| Juergen Beisert       |
> Linux Solutions for Science and Industry   Â| Phone: +49-8766-939 228   |
> Vertretung Sued/Muenchen, Germany       | Fax:  +49-5121-206917-5555 |
> Amtsgericht Hildesheim, HRA 2686 Â Â Â Â Â Â Â| http://www.pengutronix.de/ Â|
>
BR,
marek
--
as simple and primitive as possible
-------------------------------------------------
Marek Belisko - OPEN-NANDRA
Freelance Developer
Ruska Nova Ves 219 | Presov, 08005 Slovak Republic
Tel: +421 915 052 184
skype: marekwhite
icq: 290551086
web: http://open-nandra.com
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
