Hi Sascha,
as discussed at FOSDEM: *ping* ;-)
Juergen Beisert wrote:
> Using these macros simplify the configuration for special GPIO usage. But
> they should use correct bit positions for usage in the IOMUX_PAD() macro.
>
> Note: These are the bit positions of the i.MX35 CPU. Not checked for the
> other i.MX3x CPUs.
>
> Signed-off-by: Juergen Beisert <jbe@xxxxxxxxxxxxxx>
>
> ---
> arch/arm/mach-imx/include/mach/iomux-v3.h | 34
> +++++++++++++++--------------- 1 file changed, 17 insertions(+), 17
> deletions(-)
>
> Index: u-boot-v2/arch/arm/mach-imx/include/mach/iomux-v3.h
> ===================================================================
> --- u-boot-v2.orig/arch/arm/mach-imx/include/mach/iomux-v3.h
> +++ u-boot-v2/arch/arm/mach-imx/include/mach/iomux-v3.h
> @@ -68,25 +68,25 @@ struct pad_desc {
> /*
> * Use to set PAD control
> */
> -#define PAD_CTL_DRIVE_VOLTAGE_3_3_V 0
> -#define PAD_CTL_DRIVE_VOLTAGE_1_8_V 1
> +#define PAD_CTL_DRIVE_VOLTAGE_3_3_V (0)
> +#define PAD_CTL_DRIVE_VOLTAGE_1_8_V (1 << 13)
>
> -#define PAD_CTL_NO_HYSTERESIS 0
> -#define PAD_CTL_HYSTERESIS 1
> +#define PAD_CTL_NO_HYSTERESIS (0)
> +#define PAD_CTL_HYSTERESIS (1 << 8)
>
> -#define PAD_CTL_PULL_DISABLED 0x0
> -#define PAD_CTL_PULL_KEEPER 0xa
> -#define PAD_CTL_PULL_DOWN_100K 0xc
> -#define PAD_CTL_PULL_UP_47K 0xd
> -#define PAD_CTL_PULL_UP_100K 0xe
> -#define PAD_CTL_PULL_UP_22K 0xf
> -
> -#define PAD_CTL_OUTPUT_CMOS 0
> -#define PAD_CTL_OUTPUT_OPEN_DRAIN 1
> -
> -#define PAD_CTL_DRIVE_STRENGTH_NORM 0
> -#define PAD_CTL_DRIVE_STRENGTH_HIGH 1
> -#define PAD_CTL_DRIVE_STRENGTH_MAX 2
> +#define PAD_CTL_PULL_DISABLED (0)
> +#define PAD_CTL_PULL_KEEPER (0xa << 4)
> +#define PAD_CTL_PULL_DOWN_100K (0xc << 4)
> +#define PAD_CTL_PULL_UP_47K (0xd << 4)
> +#define PAD_CTL_PULL_UP_100K (0xe << 4)
> +#define PAD_CTL_PULL_UP_22K (0xf << 4)
> +
> +#define PAD_CTL_OUTPUT_CMOS (0)
> +#define PAD_CTL_OUTPUT_OPEN_DRAIN (1 << 3)
> +
> +#define PAD_CTL_DRIVE_STRENGTH_NORM (0)
> +#define PAD_CTL_DRIVE_STRENGTH_HIGH (1 << 1)
> +#define PAD_CTL_DRIVE_STRENGTH_MAX (2 << 1)
>
> #define PAD_CTL_SLEW_RATE_SLOW 0
> #define PAD_CTL_SLEW_RATE_FAST 1
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
