On Wednesday 13 June 2018 01:30:33 Mike Bird wrote:
> On Wed June 13 2018 01:25:00 William Morder wrote:
> > I don't get any error messages. I get nothing at all. The browser just
> > doesn't load over a direct connection. If you mean what do I get when I
> > run a command in a console, I am just now going through commands. So far,
> > ifconfig and iwconfig turn up nothing new; it looks normal enough.
>
> You had earlier stated that "network-aware programs cannot recognize
> wlan0". What appears in ifconfig and iwconfig?
>
> --Mike
I've already tried these; I used these commands all the time, especially
iwconfig.
ifconfig -a
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:1d:60:94:77:a4 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 0 (Local Loopback)
RX packets 552644 bytes 2130121850 (1.9 GiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 552644 bytes 2130121850 (1.9 GiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.246.154.167 netmask 255.255.252.0 broadcast 10.246.155.255
inet6 fe80::202:72ff:fe88:d1fd prefixlen 64 scopeid 0x20<link>
ether 00:02:72:88:d1:fd txqueuelen 1000 (Ethernet)
RX packets 2776170 bytes 4048306737 (3.7 GiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1449588 bytes 197469814 (188.3 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Note that I disable ipv6, so I'm curious if it has somehow got re-enabled.
iwconfig
wlan0 IEEE 802.11bg ESSID:"WHERE I LIVE"
Mode:Managed Frequency:2.412 GHz Access Point: AC:86:74:A3:66:C2
Bit Rate=54 Mb/s Tx-Power=30 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=58/100 Signal level=58/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:161 Invalid misc:41051 Missed beacon:0
lo no wireless extensions.
eth0 no wireless extensions.
But when I look at network configuration in other places (for instance, in
Trinity Control Center), no network connections at all are supposed to be
enabled.
Bill
---------------------------------------------------------------------
To unsubscribe, e-mail: trinity-users-unsubscribe@xxxxxxxxxxxxxxxxxxxxxxxxxx
For additional commands, e-mail: trinity-users-help@xxxxxxxxxxxxxxxxxxxxxxxxxx
Read list messages on the web archive: http://trinity-users.pearsoncomputing.net/
Please remember not to top-post: http://trinity.pearsoncomputing.net/mailing_lists/#top-posting
