[PATCH 3.16.y-ckt 092/180] usb: define a generic USB_RESUME_TIMEOUT macro

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



3.16.7-ckt11 -stable review patch.  If anyone has any objections, please let me know.

------------------

From: Felipe Balbi <balbi@xxxxxx>

commit 62f0342de1f012f3e90607d39e20fce811391169 upstream.

Every USB Host controller should use this new
macro to define for how long resume signalling
should be driven on the bus.

Currently, almost every single USB controller
is using a 20ms timeout for resume signalling.

That's problematic for two reasons:

a) sometimes that 20ms timer expires a little
before 20ms, which makes us fail certification

b) some (many) devices actually need more than
20ms resume signalling.

Sure, in case of (b) we can state that the device
is against the USB spec, but the fact is that
we have no control over which device the certification
lab will use. We also have no control over which host
they will use. Most likely they'll be using a Windows
PC which, again, we have no control over how that
USB stack is written and how long resume signalling
they are using.

At the end of the day, we must make sure Linux passes
electrical compliance when working as Host or as Device
and currently we don't pass compliance as host because
we're driving resume signallig for exactly 20ms and
that confuses certification test setup resulting in
Certification failure.

Acked-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
Acked-by: Peter Chen <peter.chen@xxxxxxxxxxxxx>
Signed-off-by: Felipe Balbi <balbi@xxxxxx>
Signed-off-by: Luis Henriques <luis.henriques@xxxxxxxxxxxxx>
---
 include/linux/usb.h | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/include/linux/usb.h b/include/linux/usb.h
index d2465bc0e73c..2e47496ace0d 100644
--- a/include/linux/usb.h
+++ b/include/linux/usb.h
@@ -210,6 +210,32 @@ void usb_put_intf(struct usb_interface *intf);
 #define USB_MAXINTERFACES	32
 #define USB_MAXIADS		(USB_MAXINTERFACES/2)
 
+/*
+ * USB Resume Timer: Every Host controller driver should drive the resume
+ * signalling on the bus for the amount of time defined by this macro.
+ *
+ * That way we will have a 'stable' behavior among all HCDs supported by Linux.
+ *
+ * Note that the USB Specification states we should drive resume for *at least*
+ * 20 ms, but it doesn't give an upper bound. This creates two possible
+ * situations which we want to avoid:
+ *
+ * (a) sometimes an msleep(20) might expire slightly before 20 ms, which causes
+ * us to fail USB Electrical Tests, thus failing Certification
+ *
+ * (b) Some (many) devices actually need more than 20 ms of resume signalling,
+ * and while we can argue that's against the USB Specification, we don't have
+ * control over which devices a certification laboratory will be using for
+ * certification. If CertLab uses a device which was tested against Windows and
+ * that happens to have relaxed resume signalling rules, we might fall into
+ * situations where we fail interoperability and electrical tests.
+ *
+ * In order to avoid both conditions, we're using a 40 ms resume timeout, which
+ * should cope with both LPJ calibration errors and devices not following every
+ * detail of the USB Specification.
+ */
+#define USB_RESUME_TIMEOUT	40 /* ms */
+
 /**
  * struct usb_interface_cache - long-term representation of a device interface
  * @num_altsetting: number of altsettings defined.
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]