Main benefit of this is to get xhci connected USB scanners to work.
Some devices use a clear endpoint halt request as a 'soft reset' even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side. xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host side
toggle and sequence, and get it in sync with the device side.
Cc: <stable@xxxxxxxxxxxxxxx> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@xxxxxxxxxxxxxxx>
---
drivers/usb/host/xhci-ring.c | 2 +-
drivers/usb/host/xhci.c | 100 +++++++++++++++++++++++++++++++++++++++----
drivers/usb/host/xhci.h | 2 +
3 files changed, 94 insertions(+), 10 deletions(-)
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 88da8d6..b46b5b9 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1729,7 +1729,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,
if (!command)
return;
- ep->ep_state |= EP_HALTED;
+ ep->ep_state |= EP_HALTED | EP_RECENTLY_HALTED;
ep->stopped_stream = stream_id;
xhci_queue_reset_ep(xhci, command, slot_id, ep_index);
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index ec8ac16..b06d1a5 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -1338,6 +1338,12 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags)
goto exit;
}
+ /* Reject urb if endpoint is in soft reset, queue must stay empty */
+ if (xhci->devs[slot_id]->eps[ep_index].ep_state & EP_CONFIG_PENDING) {
+ xhci_warn(xhci, "Can't enqueue URB while ep is in soft reset\n");
+ ret = -EINVAL;
+ }
+
if (usb_endpoint_xfer_isoc(&urb->ep->desc))
size = urb->number_of_packets;
else
@@ -2948,23 +2954,36 @@ void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci,
}
}
-/* Called when clearing halted device. The core should have sent the control
+/* Called after clearing a halted device. USB core should have sent the control
* message to clear the device halt condition. The host side of the halt should
- * already be cleared with a reset endpoint command issued when the STALL tx
- * event was received.
- *
- * Context: in_interrupt
+ * already be cleared with a reset endpoint command issued immediately when the
+ * STALL tx event was received.
*/
void xhci_endpoint_reset(struct usb_hcd *hcd,
struct usb_host_endpoint *ep)
{
struct xhci_hcd *xhci;
+ struct usb_device *udev;
+ struct xhci_virt_device *virt_dev;
+ struct xhci_virt_ep *virt_ep;
+ struct xhci_input_control_ctx *ctrl_ctx;
+ struct xhci_command *command;
+ unsigned int ep_index, ep_state;
+ unsigned long flags;
+ u32 ep_flag;
xhci = hcd_to_xhci(hcd);
+ udev = (struct usb_device *) ep->hcpriv;
+ if (!ep->hcpriv)
+ return;
+ virt_dev = xhci->devs[udev->slot_id];
+ ep_index = xhci_get_endpoint_index(&ep->desc);
+ virt_ep = &virt_dev->eps[ep_index];
+ ep_state = virt_ep->ep_state;
/*
- * We might need to implement the config ep cmd in xhci 4.8.1 note:
+ * Implement the config ep command in xhci 4.6.8 additional note:
* The Reset Endpoint Command may only be issued to endpoints in the
* Halted state. If software wishes reset the Data Toggle or Sequence
* Number of an endpoint that isn't in the Halted state, then software
@@ -2972,9 +2991,72 @@ void xhci_endpoint_reset(struct usb_hcd *hcd,
* for the target endpoint. that is in the Stopped state.
*/
- /* For now just print debug to follow the situation */
- xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n",
- ep->desc.bEndpointAddress);
+ if (ep_state & SET_DEQ_PENDING || ep_state & EP_RECENTLY_HALTED) {
+ virt_ep->ep_state &= ~EP_RECENTLY_HALTED;
+ xhci_dbg(xhci, "ep recently halted, no toggle reset needed\n");
+ return;
+ }
+
+ /* Only interrupt and bulk ep's use Data toggle, USB2 spec 5.5.4-> */
+ if (usb_endpoint_xfer_control(&ep->desc) ||
+ usb_endpoint_xfer_isoc(&ep->desc))
+ return;
+
+ ep_flag = xhci_get_endpoint_flag(&ep->desc);
+
+ if (ep_flag == SLOT_FLAG || ep_flag == EP0_FLAG)
+ return;
+
+ command = xhci_alloc_command(xhci, true, true, GFP_NOWAIT);
+ if (!command) {
+ xhci_err(xhci, "Could not allocate xHCI command structure.\n");
+ return;
+ }
+
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ /* block ringing ep doorbell */
+ virt_ep->ep_state |= EP_CONFIG_PENDING;
+
+ /*
+ * Make sure endpoint ring is empty before resetting the toggle/seq.
+ * Driver is required to synchronously cancel all transfer request.
+ *
+ * xhci 4.6.6 says we can issue a configure endpoint command on a
+ * running endpoint ring as long as it's idle (queue empty)
+ */
+
+ if (!list_empty(&virt_ep->ring->td_list)) {
+ dev_err(&udev->dev, "EP not empty, refuse reset\n");
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ goto cleanup;
+ }
+
+ xhci_dbg(xhci, "Reset toggle/seq for slot %d, ep_index: %d\n",
+ udev->slot_id, ep_index);
+
+ ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
+ if (!ctrl_ctx) {
+ xhci_err(xhci, "Could not get input context, bad type. virt_dev: %p, in_ctx %p\n",
+ virt_dev, virt_dev->in_ctx);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ goto cleanup;
+ }
+ xhci_setup_input_ctx_for_config_ep(xhci, command->in_ctx,
+ virt_dev->out_ctx, ctrl_ctx,
+ ep_flag, ep_flag);
+ xhci_endpoint_copy(xhci, command->in_ctx, virt_dev->out_ctx, ep_index);
+
+ xhci_queue_configure_endpoint(xhci, command, command->in_ctx->dma,
+ udev->slot_id, false);
+ xhci_ring_cmd_db(xhci);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+
+ wait_for_completion(command->completion);
+
+cleanup:
+ virt_ep->ep_state &= ~EP_CONFIG_PENDING;
+ xhci_free_command(xhci, command);
}
static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 68956b1..3b97f05 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -864,6 +864,8 @@ struct xhci_virt_ep {
#define EP_HAS_STREAMS (1 << 4)
/* Transitioning the endpoint to not using streams, don't enqueue URBs */
#define EP_GETTING_NO_STREAMS (1 << 5)
+#define EP_RECENTLY_HALTED (1 << 6)
+#define EP_CONFIG_PENDING (1 << 7)
/* ---- Related to URB cancellation ---- */
struct list_head cancelled_td_list;
struct xhci_td *stopped_td;
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html